Where is transaxle module on Chrysler town and country 2000

Check out the videos and the images tab.

https://www.google.com/search?q=2003+chrysler+town+and+country+transmission+control+module+location

..

Chris, fuse could be down under the dash to the left kind of near where your left knee would be when you are driving or under hood (engine compartment) in the fuse/relay center.
It could also be faulty flasher, wiring, etc
I will post some trouble shooting links for you.
Press the helpful button.
1996 2000 Chrysler Town and Country Interior Fuse Check 2000 Chrysler Town...

How To Install Replace Taillight and Bulb Chrysler Town Country 04 07...

Fuse Box Location in 1999 Plymouth Grand Voyager Van

Quick Tip Signs of blown IOD Fuse on Chrysler Dodge Jeep Fiat or Ram...

Thread: fuse box?? - The Chrysler Minivan Fan Club Forums

forum.chryslerminivan.net/showthread.php/21174-fuse-box

Jun 26, 2011 - 10 posts - ‎3 authors
Does anyone have a diagram for the fuse box (junction box) that is inside on the drivers side for a 1998 Town and Country. I need to know what the relays are for, my manual only shows the fuses and there is ... Forum · The Minivan Mopar Garage · 3rd Generation Chrysler Minivans: 1996-2000; fuse box?Missing: juntion

Interior Fuse Box Location: 1996-2000 Chrysler Town and ...

www.carcarekiosk.com/video/2000_Chrysler_Town_and.../replace

Interior Fuse Box Location: 1996-2000 Chrysler Town and Country ... box of your 2000Chrysler Town and Country in addition to the fuse panel diagram location. ... If youneed to replace a blown fuse in your Town and Country, make sure you ...Missing: juntion

If you have a digital display I will recomend you take it to a dealer as it may require a sca diangostics of the body controll module as there are extensive circuits in these climate control systems without the proper tools and know how damage to these circuits may occuur under misguided information

transaxle has two speed sensors input speed sensor located behind transaxle cooler lines the output sensor located far right transmission case driver side.

Hi there:
The DTC P0700 is a Information Code The Transaxle Control Module (TCM) that monitors the malfunction of sensors and actuators relating to transaxle control. If any malfunction is detected, the TCM informs the PCM by sending a signal (P0700 code). P0700 means that a code has been set in the TCM.
This code is for information ONLY. If this code is present, check for transaxle codes. So basically, the P0700 code is telling you to check the TCM for a transaxle DTC. The TCM can not turn on the check engine light so it has the PCM do it, which can only be done with a diagnostic scanner. The self retreival method for chryslers with the ignition key will not pull up the specific transmission fault codes in the TCM.


Hope this helps.

check the fuel filter connections first. If all ok, have a mechanic check it. If there is an evaporative leak, the check engine light should be on.

On the Engine/Transaxle Bell Housing area on front side of the engine compartment. (the mounting bolts for the starter go through the transaxle bell housing near the motor mount.)

(DTC) CODE # P0700....Transmission Control System (MIL Request)

Translation: Transmission Control Module (TCM) Malfunction or Failure.

P0700 Information Code

The Transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. If any malfunction is detected, the TCM informs the PCM by sending a signal (P0700 code). P0700 means that a code has been set in the TCM.

This code is for information ONLY. If this code is present, check for transaxle codes.


P1776: Solenoid Switch Valve Latched in Low/Reverse Position. The TCM monitors the L/R solenoid to ensure that the fluid transfer happens. It uses a Pressure switch to verify this. Usually this code is set by a switch that is stuck or a solenoid that is not mechanically operating.

A transmission shop would be better suited for this type of work.

Here's the location of the transmission control module.