HOW CAN I DISABLE PARK ASSIST ON JEEP COM - 2007 Jeep Commander Rocky Mountain

'year make model' would help, but here are a few that you can.

https://www.google.com/search?q=disable+park+assist

..

you will find the park assist sensor on that side where it was hit is either unplugged or broken.

How about learning to drive the car and not worrying about the Parking Assist...

How about checking your Fuses?

any ASE shop can fix cars , dealers are not god.

you can disable it, its in the oper guide how.

A WJ Jeep. with 4L I6 but what trans?
please show what lamp is glowing, exactly
do you need an operator guide (glove box) is it lost.
get one an all lamps are identified, the newer the car the more lamps.
and it gets quite overwhemling , those lamps. so dont lose the guide.
park assist disable
other feature? the oper guide will tell you all warning lamps and there
meaning.
the car is feature, rich, RTM
get the opr, guide, if it is lost.

{: ) I wonder what quit do you mean? But anyway, there are certain conditions that can disable your park assist temporarily, like the park brakes on, park assist switch disable on, an object is attached to the rear of the vehicle, dirty sensors, overspeed, speed sensors malfunction and more.
If ever one of your sensors are not working, or maybe a module or wiring problem, then it can permanently disable the park assist system, unless the problem is quickly addressed.
The most practical and fast way of tracing the cause is to use a scan tool. It will read all the codes and datas that are relevant to the problem, it can also tell which of the four sensors are at fault, thereby reducing the time of guessing.
For the moment, you can check the VEH B/U fuse 10amp at the underhood fuseblock, and IGN 1 fuse 10amps at the IP fuseblock. Goodluck.

{: ) The "Service Park Assist" message cannot be erased or reset until the main cause of the problem is resolved. It will just keep on coming back. Let's say one or more of the park assist sensors are faulty, you should have it repaired or replaced first before the scan tool can successfully clear the trouble codes that were present then.
The SERVICE PARK ASSIST message is a reminder that a fault has been detected by the parking assist system and it will disable this system until the problem is being addressed. A scan tool can effectively trace the cause of the fault.

{: ) SERVICE PARK ASSIST The driver information center (DIC) displays SERVICE PARK ASSIST when the park assist module detects a malfunction in the object detection system and sends a request to the DIC for display of the message. The DIC also displays SERVICE PARK ASSIST when there is a loss of communication with the park assist module.
PARK ASSIST OFF The PARK ASSIST OFF message is displayed in the DIC when the park assist system is disabled due to conditions that disable or inhibit the system. The red LED in the rear display, as well as, the telltale in the switch will be lit, notifying the driver the PARK ASSIST system is disabled. The object alarm module requests the DIC via the serial data circuit to display PARK ASSIST OFF when it detects that one of the following conditions is true:
• The object alarm system is disabled through DIC vehicle customization feature. Refer to the Owners Manual for more information. • An object is attached to the rear of the vehicle, such as a trailer, bicycle rack, or hitch receiver. • An object is hanging out of the endgate. • The park brake is not fully released. • The system receives vibrations from a large nearby vehicle or from a heavy equipment such as a jackhammer. In the case of objects attached to the rear of the vehicle such as a trailer, hitch receiver, or a bicycle rack, or objects hanging out of the endgate, the rear parking assist (RPA) will have an Automatic Object induced disable feature where the RPA will determine if the rear object is moving with the vehicle. If the RPA detects such a condition, the park assist will be disabled. The PARK ASSIST OFF message will continue to be displayed until the trailer hitch receiver is removed and the vehicle is driven forward above 24 km/h (15 mph).

The park assist system detects objects 59 inches or less in back of your vehicle, to warn u so u don't strike the object. I'm guessing that since the service park assist system comes on in the ice and snow, the monitor is detecting something (ice and snow covering the sensor). If u clean off the snow and ice, the message should shut off.

Is the hand brake working properly because if the rubber and springs used to brake the rear wheels is loose, the security assist system goes off and usually a bell rings and what not.