Where is egr valve located on 2.2 ecotec - 2002 Pontiac Grand Am

4 cylinder model the EGR valve is located between 2 & 3 cylinder on intake manifold and between Carb and valve cover it has a diaphragm cover about 3 inches round and one vacuum hose 2 bolts holds it to the intake. V-6 models EGR valve is located on drivers side of engine just behind carb and about the same size and roundness and one hose two bolts.

Where is the EGR valve on a 2011 CHEVY Equinox? LS 2.4L

The egr valve is below the throttle body, at the rear of the engine. The egr valve attaches to the bottom of the intake manifold plenum.-------------------------------------------------------------------------
vas 5054a

I have a 05 Chevy cav with a 2.2 ecotec without egr I found out they make two motors one with and one without egr

Hi thanks for your question' The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head ,

1. Remove electrical connector (5) at top of EGR valve solenoid.
2. Remove tube mounting bolt (1) at intake manifold.

1. Remove two bolts (4) connecting EGR tube (1) to valve assembly.
2. Remove gasket located between EGR tube flange and EGR valve assembly.
3. Remove two EGR valve mounting bolts (5).
4. Separate valve assembly (3) from engine.
5. Remove and discard metal gasket located between cylinder head and valve assembly.

INSTALLATION

1. Clean area at rear of left cylinder head where it joins base of EGR valve.
2. Clean EGR tube where it joins EGR valve.
3. Position new gasket between EGR valve and cylinder head.
4. Position EGR valve to cylinder head. Install and tighten two bolts (5). Refer to Torque Specifications.
5. Position new gasket between EGR tube flange and EGR valve assembly.
6. Position EGR tube (1) to side of EGR valve and into intake manifold.
   1. Install EGR tube flange bolt (1) at intake manifold. Tighten bolt. Refer to Torque Specifications.
   2. Connect electrical connector (5) to top of EGR valve solenoid (2).Do a final tightening of two EGR tube bolts (4). Refer to Torque Specifications

The electronic EGR valve and solenoid assembly (3) is attached to the front of the right cylinder head (1). An exhaust gas routing tube connects the EGR valve to the intake manifold.



Disconnect electrical connector (1) from EGR solenoid (2). Remove two bolts (3) connecting EGR tube (4) to valve assembly. Remove gasket located between EGR tube flange and EGR valve assembly.

Remove two mounting bolts (2). Separate valve assembly (3) from cylinder head (1). Remove and discard metal gasket located between cylinder head and valve assembly.
The new EGR valve will come with a new metal gasket. You can reuse the smaller gasket for the metal pipe going to the egr valve as long as its not damaged.

TY for using Fixya; remember rated this post.

Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} EXHAUST GAS RECIRCULATION (EGR) VALVE REPLACEMENT

REMOVAL PROCEDURE 1. Turn OFF the ignition. 2. Disconnect the EGR valve electrical connector 3. Remove the bolt retaining the pipe assembly from the EGR valve and carefully pull the pipe assembly back. 4. Remove the EGR valve retaining bolts. 5. Remove EGR valve assembly. 6. Remove the gasket. INSTALLATION PROCEDURE
1.
Install the EGR Valve with a new gasket to the intake manifold. NOTE: Refer to Fastener Notice in Service Precautions. 2. Install the bolts through the EGR valve. Tighten Tighten the bolts to 30 N.m (22 lb ft) 3. Connect the pipe assembly to the EGR valve. 4. Install the bolt. Tighten Tighten the bolts to 30 N.m (22 lb ft) . Connect the EGR valve electrical connector.

the egr valve is located at the end of an exhaust supply pipe (1/2" diameter) from the exhaust manifold. there is also a sticker under the hood that shows this location, it is the emissions sticker.

The EGR Valve Location is typically housed on the intake manifold this schematic may help you
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528008822d

The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head ,

1. Remove electrical connector (5) at top of EGR valve solenoid.
2. Remove tube mounting bolt (1) at intake manifold.

1. Remove two bolts (4) connecting EGR tube (1) to valve assembly.
2. Remove gasket located between EGR tube flange and EGR valve assembly.
3. Remove two EGR valve mounting bolts (5).
4. Separate valve assembly (3) from engine.
5. Remove and discard metal gasket located between cylinder head and valve assembly.

INSTALLATION

1. Clean area at rear of left cylinder head where it joins base of EGR valve.
2. Clean EGR tube where it joins EGR valve.
3. Position new gasket between EGR valve and cylinder head.
4. Position EGR valve to cylinder head. Install and tighten two bolts (5). Refer to Torque Specifications.
5. Position new gasket between EGR tube flange and EGR valve assembly.
6. Position EGR tube (1) to side of EGR valve and into intake manifold.
   1. Install EGR tube flange bolt (1) at intake manifold. Tighten bolt. Refer to Torque Specifications.
   2. Connect electrical connector (5) to top of EGR valve solenoid (2).Do a final tightening of two EGR tube bolts (4). Refer to Torque Specifications