Idle air control valve - 2007 Ford Mustang GT California Special Convertible

2001 KIA RIO IAC/ Idle Air Control Valve Testing and Cleaning
https://www.youtube.com/watch?v=jgbTdyeaWbM
Cleaning an Idle Air Control Valve and Throttle Body (Kia Sportage)
https://www.youtube.com/watch?v=7k5U4jqujh0
Location Idle air control valve IAC valve
https://www.kia-forums.com/1g-2001-2005-rio/52402-where-egr-valve-idle-air-control.html

It's IAC - idle air control valve , not fuel injector idle air control valve. It's located on the throttle body -air inlet for the engine .
Idle Air Control Valve

I recommend you test the idle air control valve. See procedure below. If this is not the problem, please read additional possibilities at the link below.


Operation


The Idle Air Control (IAC) valve controls the amount of air that bypasses the throttle valve, which controls the engine idle speed. The IAC valve consists of windings, an armature, a return spring, and a rotary slide. The engine control module (ECM) pulses the voltage to the winding, the opposing forces on the armature by the return spring cause it to maintain a fixed position, adjusting the amount of bypass air to maintain the correct idle speed.

Removal & Installation


Turn the ignition switch to the OFF position.
Disconnect the idle air control valve harness electrical connector.
Using a suitable tool, remove idle air control valve.
Installation is in reverse order of removal.

Testing


Checking Idle Air Control Valve (IAC) Triggering
Check IAC valve is electrically OK.
Slide up boot on the IAC valve connector.


Fig. IAC Connector
Use scan tool 'Output Diagnostic Test Mode' function 03 to trigger the IAC valve - N71.Connect VAG 1527B voltage tester, or equivalent, between terminal 1 and engine ground (GND). Voltage tester must flash.Connect VAG 1527B voltage tester, or equivalent, between terminal 2 and battery positive voltage (B+). Voltage tester must light up.If specified results are not obtained:Connect VAG 1598/19 test box, or equivalent, to ECM harness connector.Check the wiring between harness and connector terminal 1 (in engine compartment) to test box socket D11 . Then check the wiring between harness connector terminal 2 and test box socketD9 using wiring diagram. Repair as necessary.If the wiring is okay, but triggering still does not occur, replace the ECM.If the triggering signal and the wiring are okay and the valve does not react, replace the IAC valve. Checking Mechanical Function
Remove the idle air control (IAC) valve.Visually check the surface of the rotary slide (arrow) for signs of wear.




Fig. Showing the IAC Valve

WARNING
Do NOT check for ease of movement by prying on the rotary slide with a screwdriver or other tools that could cause scratching or other damage.

Reconnect the IAC valve, while still removed, to the harness connector.Use scan tool 'Output Diagnostic Test Mode' function 03 to trigger IAC valve - N71.Check whether rotary slide moves freely from stop to stop.If there are signs of scoring, or if the rotary slide does not move freely in both directions, replace the IAC valve.If the IAC valve does not respond (not triggered) during the Output Diagnostic Test Mode, check triggering. Resistance Test
Remove the idle air control valve harness connector.Use a suitable Digital Multimeter (DMM) to measure the resistance between the 2 terminals of the idle air control valve.The correct measurement should be 7-11 ohms. If not, replace the idle air control valve.
NOTE
At room temperature, the resistance value will be lower. The resistance value will be higher if the Idle Air Control (IAC) valve is measured at under-hood operating temperatures.

Reconnect the idle air control valve harness connector.The idle air control valve should hum and vibrate slightly when the ignition is turned 'ON'. If not, the ECM or harness may be defective.

Do It Yourself Diagnosis and Repair

Vacuum leak, idle air control motor and solenoid, stuck throttle cable if equipped, throttle position sensor

Mark, IAC (Idle Air Control Valve), If engine is idling too fast, problem may not be the idle speed control system, but an engine vacuum leak. Check for vacuum leaks first to rule this possibility out. Also on your Toyota low coolant, air in the cooling system can cause the valve not to operate properly as I believe coolant has to run through valve for it to operate correctly. Fill/bleed air from cooling system. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Idle Air Control Valve Toyota Nation Forum Toyota Car and Truck Forums
Troubleshoot Idle Speed Control System
Has Anyone Cleaned Their IAC Idle Air Control Valve Toyota Nation Forum...

change the idle air control valve.

Idle Air Control (IAC) Valve OPERATION The Idle Air Control (IAC) valve controls the engine idle speed and dashpot functions. The valve is located on the side of the throttle body. This valve allows air, determined by the Powertrain Control Module (PCM) and controlled by a duty cycle signal, to bypass the throttle plate in order to maintain the proper idle speed. Fig. 1: Typical Idle Air Control (IAC) valve which is mounted to the throttle body - cutaway view shows air bypass direction
--- REMOVAL & INSTALLATION

1. Disconnect the negative battery cable. To remove the IAC valve, first disconnect the negative battery cable, then the IAC wire harness plug
   Next, remove the two IAC valve attaching bolts . . .
   . . . and pull the valve from the intake manifold
   
   
2. Disengage the wiring harness connector from the IAC valve.
3. Remove the two retaining screws, then remove the IAC valve and discard the old gasket. To install: When installing the valve, always discard the old gasket and install it using a new one
   
   
4. Clean the IAC valve mounting surface on the throttle body of old gasket material.
5. Using a new gasket, position the IAC valve on the throttle body. Install and tighten the retaining screws to 71-106 inch lbs. (8-12 Nm).
6. Attach the wiring harness connector to the IAC valve.
7. Connect the negative battery cable.

OPERATION The Idle Air Control (IAC) valve controls the engine idle speed and dashpot functions. The valve is located on the throttle body on. This valve allows air to bypass the throttle plate. The amount of air is determined by the Powertrain Control Module (PCM) and controlled by a duty cycle signal. Fig. 1: Cleanable IAC valve — 5.0L engine version shown, others similar
Fig. 2: Non-cleanable IAC valve — 5.0L engine version shown, others similar
TESTING OBD-I System

1. Make sure the ignition key is OFF.
2. Disconnect the air control valve.
3. Use an ohmmeter to measure the resistance between the terminals of the valve solenoid. NOTE: Due to the diode in the solenoid, place the ohmmeter positive lead on the VPWR pin and the negative lead on the ISC pin.
   
4. If the resistance is not 7–13 ohms, replace the air control valve.

---
REMOVAL & INSTALLATION Fig. 1: Idle air control valve mounting — 4.9L engine version shown, others similar

1. Disconnect the negative battery cable.
2. Disconnect the engine wiring to the IAC sensor.
3. Remove the two retaining screws for the valve.
4. Remove the IAC valve and discard of the old gasket. Fig. 2: Disengage the idle air control solenoid electrical connection
   Fig. 3: Loosen the idle control solenoid retaining screws
   Fig. 4: Remove the idle air control solenoid from the throttle body
   To install:
   
5. Clean the area of old gasket material.
6. Using a new gasket, attach the IAC valve to the engine. Tighten the retaining screws to 71–102 inch lbs. (8–12 Nm).
7. Connect the IAC valve wiring to the unit.
8. Connect the negative battery cable.

IDLE CONTROL VALVE: REMOVAL
1.Disconnect the vacuum hose from the exhaust gas recirculation valve.
2.Disconnect the idle air control valve electrical connector. 3.Detach the idle air control valve wiring harness from the stud.

4.Remove the idle air control valve.

• Remove the two nuts.

I hope this is concise enough for you. Please give me thumbs up to thank me. By the way did I mention this info is FREE!!!

may just need cleaning with carb cleaner.

here is 1996, oldest I have:

Section 03-14: Engine Controls, Electronic 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Idle Air Control (IAC) Valve Removal

1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
   

1. Disconnect the engine control sensor wiring (12A581) from the idle air control valve (IAC valve) (9F715) at the idle air control valve electrical connector.
   

1. Remove the two idle air control valve retaining bolts.
   

1. Remove the idle air control valve and idle air control valve gasket.
   

Installation

1. NOTE: If scraping is necessary, be careful not to damage idle air control valve gasket surfaces, or drop material into intake manifold (9424) or throttle body (9E926) (depending upon application).
   
   Clean idle air control valve gasket mating surfaces.
   

1. To install idle air control valve, reverse Removal procedure.
   

1. Tighten the idle air control valve retaining bolts to 8-12 Nm (71-106 lb-in).
   

it's on the throttle body. Here's a Quest with same 3.0L engine. These often need cleaning with carb or throttle body cleaner

Idle Air Control (IAC) Valve When the engine (6007) is running but not at idle, the throttle valve controls the amount of air admitted into the engine. The powertrain control module (PCM) (12A650) increases the fuel injection output in proportion to the increased airflow to achieve the appropriate air/fuel ratio. During idle, the throttle valve is almost fully closed. It is therefore necessary for the idle air control system to supply air for combustion during idle. The idle air control (IAC) valve allows a metered amount of air to enter the intake manifold (9424). The camshaft position (CMP) sensor detects engine speed and sends a signal to the PCM. The PCM sends a duty cycle (On/Off) signal to the IAC valve which allows additional air to enter the intake manifold. Air is added by the IAC valve to maintain the set lowest idle speed at which the engine can operate. The idle speed adjusting screw allows adjustment of the airflow into the intake manifold.


Fast Idle Control (FIC) Solenoid The fast idle control (FIC) solenoid helps maintain a constant idle speed while the air conditioning is operating. When the air conditioning is turned on, the front climate control panel sends out two signals. One signal is sent to the powertrain control module (PCM) (12A650) to engage the A/C compressor (19703). The second signal is a ground signal sent to the FIC solenoid relay, to engage the FIC solenoid. The FIC solenoid supplies additional air to adjust the increased engine load.