Code po131 oxygen sensor circuit,low volts sensor 1

codes PO131 PO151 PO154 okay. code PO131 - o2 sensor circuit low voltage bank 1 sensor 1. code PO151 - o2 sensor circuit low voltage bank 2 sensor 1. code PO154 - o2 sensor circuit no activity detected bank 2 sensor 1

P0131 - O2 Sensor Circuit Low Voltage Bank 1 Sensor 1 (sensor is before the catalytic converter)

Possible causes- Front Heated Oxygen Sensor Bank 1 harness is open or shorted
- Front Heated Oxygen Sensor Bank 1 circuit poor electrical connection
- Faulty Front Heated Oxygen Sensor Bank 1
- Inappropriate fuel pressure
- Faulty fuel injectors
- Intake air leaks may be faulty
- Exhaust gas leaks
P0132 - O2 Sensor Circuit High Voltage Bank 1 Sensor 1
Possible causes- Front Heated Oxygen Sensor Bank 1 harness is open or shorted
- Front Heated Oxygen Sensor Bank 1 circuit poor electrical connection
- Faulty Front Heated Oxygen Sensor Bank 1
- Inappropriate fuel pressure
- Faulty fuel injectors
- Intake air leaks may be faulty
- Exhaust gas leaks

I am not really sure what is going on here with the same O2 sensor giving these lean and rich codes, if nothing else is apparent and the engine runs well you may have a defective O2 sensor.

Reset error codes by disconnecting battery for 5 minutes. Start fresh. all codes should be clear now. drive and see if any new codes come on. They are the ones you need to address.

- Front Heated Oxygen Sensor Bank 1 harness is open or shorted
- Front Heated Oxygen Sensor Bank 1 circuit poor electrical connection
- Faulty Front Heated Oxygen Sensor Bank 1
- Inappropriate fuel pressure
- Faulty fuel injectors
- Intake air leaks may be faulty
- Exhaust gas leaks

Replacing the O2 Sensor 1 usually takes care of the problem

The front heated oxygen sensor (or O2 sensor 1) is placed into the exhaust manifold. It detects the amount of oxygen in the exhaust gas compared to the outside air. The heated oxygen sensor 1 has a closed-end tube made of ceramic zirconia. The zirconia generates voltage from approximately 1V in richer conditions to 0V in leaner conditions. The heated oxygen sensor 1 signal is sent to the Engine Control Module (ECM). The ECM adjusts the injection pulse duration to achieve the ideal air-fuel ratio. The ideal air-fuel ratio occurs near the radical change from 1V to 0V.

Hi,
Upstream Oxygen sensor low voltage output bank1. Usually a bad o2 sensor. Bank 1 is cylinders 1-3-5 and upstream sensor usually on exhaust manifold. Replacement is recommended to clear the fault....Mike

P0131=O2 Sensor Circuit Low Voltage Bank 1 Sensor 1
P0151=O2 Sensor Circuit Low Voltage Bank 2 Sensor 1
Marc,
this shows that the oxygen sensor on the left exhaust pipe before converter is bad,
And the front oxygen sensor on the right exhaust infront of converter is bad.

Code PO131 is O2 sensor circuit low voltage , bank 1, sensor 1. That sensor I would say is the one in the exhaust manifold. I would check voltage to the sensor from the computer. If the voltage is not 5 volts, then it could be a computer problem or a wiring problem. I have seen factory wiring and connectors give a voltage problem. Check for a damaged or burnt, pinched wire. You need to know for sure that the voltage is correct to the sensor. Intermittent problems are hard to trace , but patience and knowledge helps.

P0131 - Heated Oxygen Sensor (HO2S) Circuit Low Voltage

P1133 - Heated Oxygen Sensor (HO2S) Insufficient Switching Bank 1 Sensor 1


Bank 1 Sensor 1
P0300 - Engine Misfire Detected

I would check for vacuum leaks, maybe intake or brake booster