Door handle how to replace door handle

Remove door panel, then unbolt handle. Verify no screws in door panel then yank. Screws probably in armrest and by door handle, maybe under switch pod lid

Search Results

How To Install Replace Inside Door Handle Chevy Equinox ...

? 9:02
https://www.youtube.com/watch?v=cY6asyM2R6g
Feb 2, 2012 - Uploaded by 1A Auto Parts
How To Install Replace Inside Door Handle Chevy Equinox 05-09 1AAuto.com .... found your tutorial on fixing my driver's side door handle for my 2006 Equinox. .... Door Handles Chevy Equinox 2010 2011 2012 GMC Terrain ...

How To Install Replace Inside Door Handle 2007-13 ...

? 9:05
https://www.youtube.com/watch?v=QonKLwhk2CE
Apr 2, 2015 - Uploaded by 1A Auto Parts
http://www.1aauto.com/interior-door-handle-driver-side-front/i/1adhi00417 1A Auto shows you how to repair, install, fix,change or replace a broken or snappe... ... 10, 11, 12, 13 Chevy Silverado, Tahoe, Suburban and GMC Sierra, Yukon Denali ...2007-2011 Tahoe Yukon Suburban Escalade Vent Section ...Missing: terrain

How To Install Remove Rear Outside Door Handle 2007-13 ...

? 10:02
https://www.youtube.com/watch?v=7ZUTqqEzpZg

1. How it's done:
   1. Remove the door panel to gain access.
   2. Remove and replace the broken door handle.
   3. Inspect door latch and replace if not working.
   4. Check door for proper operation.
   5. Reinstall door panel.
   
   

Door Handle or Door Latch Replacement Service Cost YourMechanic

door handle broke depends on what door handle it is.if door cant be open on out side out side door handle broke.if cant open door on inside inside door handle broke.door handle clip that connects to latch rod broken.when you try open door handle not engage to latch rod.door not going open.have to replace door handle with new clip holds latch rod in place.

just a door handle kit. it isnt a part off the door handle. unless your refering to the door pull and not the door opener, in wich case you would have to change panel

There are a few after-market sellers who offer door handles for most cars on ebay, reasonably priced. Go to www.ebay.com and enter "Subaru Loyale door handle" in the search bar. Alternatively, you can order one from a salvage yard, try www.car-parts.com. And of course, if money is no object, you can check with your local Subaru dealer's parts department.

Replacement is not too hard. You may be able to do it without even removing the door panel. There is a screw that holds the handle in the door. Undo it, then slide the handle back and forth gently to loosen it from its set holes, and pull it away from the door panel. Then unfasten the door lock connecting rod/hook from the back side of the handle assembly. Fasten the new handle on the hook, re-insert into the door panel, set the handle in place, and replace the holding screw.

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can remove the inner door handle and replace with new one. If it's your outer door handle, pull back the weather seal and disconnect the linkage to the outer door handle and then remove the bolts securing the outer handle to the door

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can replace your inner door handle. If it's your outer door handle, pull back the weather seal and remove the bolts and disconnect the linkage from that handle

Have you been replacing the handles with aftermarket replacements made in China. If so, spend the extra $$ to get the parts from a GM dealer. They obviously break too but perhaps not as easily.

remove door panel.. inside door you will see a rod going to the handle..on the end is a clip ..push the clip up off the rod .slide the rod out..remove 2 ..13mm nuts from handle ..remove handle