CONROD TORQUE SPECIFICATION FOR 5A-FE ENGINE

What are the torque specs for the rod bearings on a 2006 - Fixya

https://www.fixya.com > ... > 2006 Dodge Caravan
Nov 15, 2019 - What is the torque specification for the inner tie rod 1996 .dodge caravan 2.4 liter. 45-55 foot pounds. Read full answer. Sep 18, 2012 • 1998 ...
SOLVED: Torque chart for dodge caravan 4l - Fixya
Sept 9, 2019
Main bearing torque spec for Dodge Grand Caravan 2005
Sept 15, 2019
Im trying to find the connector rod bearing torque - Dodge - Fixya
Jul 15, 2018
Head bolt torque specs for 2.4L dohc dodge caravan - Fixya
Jun 2, 2012
More results from www.fixya.com

Dodge Caravan 2.4 need engine tightening specs and head ...

https://www.justanswer.com > chrysler > 28qv6-dodge-...
Jun 27, 2009 - SPECIFICATIONS - TORQUE ; Balance Shaft Carrier Cover-Bolts, 12, - ; Camshaft Sprocket-Bolt, 101, 75 ; Connecting Rod Cap-Bolts, 27 +¼ turn, 20 +¼ ...
1 answer · Top answer: Here are the head bolt specs: Before installing the bolts, the threads should be coated with ...

Torque Specifcations - MAHLE Aftermarket

https://www.mahle-aftermarket.com > media > torque3
PDF
Engine Model Year. Rod Torque. Main Torque. Cylinder Head Bolt Torque. CASE. 2.4. 148. 61-66. 45-50 FT/LBS. 90-100 FT/LBS. 60-65 FT/LBS. CASE. 2.4.
124 pages
You've visited this page 3 times. Last visit: 01/02/22

1. Tighten the cylinder head bolts in the sequence shown. Using the 4 step torque turn method, tighten according to the following values:

• • Step 1: All to 34 Nm (25 ft. lbs.)
  • Step 2: All to 68 Nm (50 ft. lbs.)
  • Step 3: All to 68 Nm (50 ft. lbs.)

CAUTION: Do not use a torque wrench for the following step.
Step 4: Turn an additional 1/4 turn

• Step 5: Install and tighten bolts (1-10) in sequence shown, to 41 Nm (30 ft. lbs.) .

1. Tighten bolts (1-10) again to 41 Nm (30 ft. lbs.) PLUS 1/4 turn in sequence shown.
2. Install main bearing bedplate to engine block bolts (11-20), and torque each bolt to 28 Nm (20 ft. lbs.) in sequence shown.

Connecting Rod Cap Bolts 54 Nm (40 ft. lbs.) + 1/4 turn
1997 Jetta: Torque settings..vw..the head, fly wheel, big ends.


1997 Jetta3 1800 feul injection


Vibration Damper/belt Pulley
Tighten 20 Nm (14.8 ft lb) Crankshaft Toothed Belt Sprocket Tighten 90 Nm (66 ft lb) + 90° Camshaft Sprocket Tighten 80 Nm (60 ft lb) Main Bearing Cap
Tighten 65 Nm (48 ft lb) FLYWHEEL TORQUE
Torque 60 Nm. (44 ft. lbs.) + 1/4 turn (90°) [1] [1] Always replace bolts.
CYLINDER HEAD TIGHTENING TORQUE [1] :
1st sequence: 40 Nm (30 ft lb)
2nd sequence: 60 Nm (43 ft lb)
Final sequence: plus 1/2 turn (180°)
Here are some additional specifications, thanks
ntake Manifold
Mounting Bolts 25 Nm (18 ft. lbs.) Bearing Cap Nut 20 Nm (15 ft. lbs.) Rod Bearing Cap
Assembly
Tighten 30 Nm (22 ft lb) + 90° To measure radial clearance
Tighten 30 Nm (22 ft lb) but NOT additional 90° TIGHTENING SPECIFICATIONS
Oil Pump Bolt 20 Nm (14 ft. lbs.) Oil Tube To Block 10 Nm (7 ft. lbs.) Exhaust Manifold to Cyl. Head 25 Nm (18 ft lb) Exhaust Manifold to Front Exhaust Pipe 40 Nm (30 ft lb) Water Pump
TIGHTENING SPECIFICATIONS
Cover Bolts 10 Nm (7 ft. lbs.) Mounting Bolt and Studs 20 Nm (15 ft. lbs.) + 1/4 turn (90°) Pulley Bolts 25 Nm (18 ft. lbs.)

TIGHTENING SPECIFICATIONS
Connecting Rod Nuts:
Tighten In Two Stages:
First Stage 30 Nm (22 ft. lbs.) Second Stage turn an additional 90°(1/4 turn)

I need all the specs of Isuzu npr 4hg1 engine.Cylinder head bolts torque, crankshaft bolts torque, connecting rod caps bolts torque
.

Torque Specs Database

Type: Dim: Length: Head: Nut Grade: 20 Ft-Lbs 240 In-Lbs 27.12 N-m Connects: Connecting Rod To Engine Block Years: All Vote Record: Vote Note: Vortec - Rod Cap Nuts - 2 Steps: 20 FtLbs; +70degs

http://ww2.justanswer.com/uploads/ZZdaryl/2009-06-14_153454_torque.pdf

Main Bearing Cap Bolt 4.3L Step 1 15 ft lbs (20) Step 2 Additional 73 Degrees

i don't know if that's correct for main bearing caps since another link states it's much higher

4 3 Vortec Piston Specs eHow

hopefully a GM guy will chime in to confirm the main bearing torque

the rod bearing torques are the same on all the other links

cylinder head bolt torque

52-55 ft lbs. cold engine
59-63 ft lbs. hot engine

connecting rod cap nut 26-28 ft lbs. SOHC
connecting rod cap nut 23-26 ft lbs. DOHC

main caps 41-44 ft lbs.

TORQUE SPECIFICATIONS kia rio
Cylinder Head Bolts:
(21.7ft.lb) or (3.0kgf.m) 90?

Crank Main caps Tightening Torque

For the 12 Pointed Head Bearing Cap Sub-Assembly Bolts
Start from center bolts and tighten in a clockwise rotation working out
Step 1 all bolts 22 Nm or 16 ft lb
Step 2 all bolts 44 Nm or 32 ft lb
Step 3 all bolts 45 degrees additional clockwise rotation using an angle indicator.
Step 4 all bolts 45 degrees additional clockwise rotation using an angle indicator.

Hexagon Head Bearing Cap Sub-Assembly Bolts
1ZZ-FE Engine 18.5 Nm (14 ft.lb)
2ZZ-GE Engine 18 Nm (13 ft.lb)

Connecting rod:
1. Apply a light coat of engine oil on the threads and under the heads of the connecting rod cap bolts.
2. Install and alternately tighten the 2 connecting rod cap bolts in several passes. Torque: 1ZZ-FE: 20 Nm (204 kgf-cm, 15 ft. lbs.) 2ZZ-GE: 30 Nm (306 kgf-cm, 22 ft. lbs.) If any of the connecting rod cap bolts does not meet the torque specification, replace the connecting rod cap bolts.
3. Retighten the cap bolts by 90° more
4. Check that the crankshaft turns smoothly.

Here you go...

Connection Rod Nuts: 37-38 Ft Lbs.
Main Bearing Caps: 55-61 Ft Lbs.
And Head Bolts...

1st - step; - 80 ft./lbs. 2nd - step, loosen all bolts; 3rd - step; - 80 ft./lbs.

Torque sequence:
Step 1: Torque 29 to 34 Ft/Lbs
Step 2: Torque an additional 90 to 120 degrees