Question about Oldsmobile Silhouette

Open Question

Engine oil cooler lines - Silhouette Oldsmobile Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
keemo68

Ronald Mueller

  • 1263 Answers

SOURCE: oil cooler lines

the oil cooler lines connect to the tank portion of the radiator there should be one port on top and one port towards the bottom the ports should be no more than 3/8 inches in diameter

Posted on Sep 01, 2008

Ad

Anonymous

  • 3 Answers

SOURCE: oil leaking from oil cooler line

Check the o-rings in the female side.

Posted on Dec 29, 2008

robert wales

  • 4977 Answers

SOURCE: engine oil cooler line leaking. Is it easier to

its best to replace the oil cooler lines.this should have the lines that run from the radiator to the oil filter housing and when you replace the line you will get both lines as they are made be replaced together.bypassing the line is hard to do takes more time and will leak as you can`t get it to seal properly.

Posted on Sep 15, 2011

brandon

  • 24 Answers

SOURCE: My 1995 Chevy Caprice 5.7 Police Interceptor model had the GM parts oil cooler lines replaced because of a leak, and shortly after that, the check engine light came on and the car went into trans limp

sound slike a problem with the tcc selonoid wich is the torque converter lock up selonoid

Posted on Sep 26, 2012

Derail

  • 157 Answers

SOURCE: engine oil cooler lines leaking can I remove lines and install plugs in oil filter housing were lines went

not recomended,replace the lines, generally can get new one for abt 40 to 60 bucks, not sure which engine you have or i would have priced exactly 4 you.

Posted on Sep 28, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove radiator on 2000 Lincoln Continental


RADIATOR
Removal
1. Disconnect battery ground cable.
2. Drain engine cooling system as described.
3. Remove engine air cleaner.
4. Remove upper radiator hose from water bypass tube.
5. Remove radiator overflow hose from radiator and fan shroud.
6. Remove transmission oil cooler line from oil cooler inlet fitting.
7. Remove nuts retaining A/C condenser core to the radiator.
8. Disconnect engine control sensor wiring from the auxiliary electric cooling fan motors and the CCRM.
9. Raise vehicle on hoist.
10. Remove splash shield from lower radiator support and front sub-frame.
11. Remove lower radiator hose from radiator.
12. Remove oil transmission cooler line from oil cooler outlet fitting on radiator.
13. Remove retaining screws for power steering/transaxle oil cooler and position cooler aside.
14. Support fan shroud, radiator and A/C condenser core with a suitable jackstand. Remove lower radiator
support.
15. Position jackstand aside and carefully remove radiator and fan shroud.
16. Remove two retaining bolts for fan shroud at top of radiator and remove fan shroud from radiator.
17. Remove upper radiator hose from radiator.
NOTE: Loosen transmission oil cooler lines while securely holding radiator
connector with a back-up wrench.
NOTE: Loosen transmission oil cooler lines while securely holding radiator
connector with a back-up wrench.
18. Remove the radiator.

Oct 21, 2016 | Lincoln Cars & Trucks

1 Answer

3.9l. How can I replace engine oil cooler lines?


This should be a straight forward swap to a new line. Loosen fittings, remove clips, unscrew retainer on block and drain oil from old line to avoid messy spills and replace.

Video Chevy Astro Van Oil Cooler Lines Replacement - Should be a very similar procedure for your Impala.

625 665 How to replace an oil cooler line


Find part information here:
Dorman Hose Engine Oil Cooler 625 665 ReadReviews onDorman

May 15, 2016 | 2006 Chevrolet Impala

1 Answer

How do I change the radiator on a 96 lincoln contiental 32v intech V8 ?


RADIATOR
Removal
1. Disconnect battery ground cable.
2. Drain engine cooling system as described.
3. Remove engine air cleaner.
4. Remove upper radiator hose from water bypass tube.
5. Remove radiator overflow hose from radiator and fan shroud.
6. Remove transmission oil cooler line from oil cooler inlet fitting.
7. Remove nuts retaining A/C condenser core to the radiator.
8. Disconnect engine control sensor wiring from the auxiliary electric cooling fan motors and the CCRM.
9. Raise vehicle on hoist.
10. Remove splash shield from lower radiator support and front sub-frame.
11. Remove lower radiator hose from radiator.
12. Remove oil transmission cooler line from oil cooler outlet fitting on radiator.
13. Remove retaining screws for power steering/transaxle oil cooler and position cooler aside.
14. Support fan shroud, radiator and A/C condenser core with a suitable jackstand. Remove lower radiator
support.
15. Position jackstand aside and carefully remove radiator and fan shroud.
16. Remove two retaining bolts for fan shroud at top of radiator and remove fan shroud from radiator.
17. Remove upper radiator hose from radiator.
NOTE: Loosen transmission oil cooler lines while securely holding radiator
connector with a back-up wrench.
NOTE: Loosen transmission oil cooler lines while securely holding radiator
connector with a back-up wrench.
18. Remove Radiator

Apr 19, 2015 | 1996 Lincoln Continental

1 Answer

How to replace oil; cooler on this year


  • Service and Repair
Oil Cooler Replacement

Removal Procedure

  1. Raise and support the vehicle. Refer to Vehicle Lifting.
  2. Drain the engine oil and remove the oil filter housing.
89116492

  1. Loosen the oil cooler outlet (1) and the inlet (2) lines from the engine block.
  2. Lower the vehicle.
  3. Remove the intake plenum.
  4. Remove the intake manifold.
89116493

  1. Disconnect the following electrical connectors from the water crossover:
    • The engine coolant temperature sender (2)
    • The engine coolant temperature sensor (4)
84936658

  1. Remove the water crossover bolts (1).
  2. Remove the water crossover upper and lower seals (2).
84942881

  1. Loosen the upper heat shield bolts on the left side of the exhaust manifold.
89116496

  1. Remove the oil cooler outlet line from the engine oil cooler.
  2. Remove the oil cooler inlet line from the engine oil cooler.
84942883

  1. Note the positioning of the 4 seals.
84972057

  1. Position the oil feed and return,lines out of the way and secure with mechanic wire.
  2. Remove the engine oil cooler, inlet and outlet nuts (1).
  3. Remove the engine oil cooler cover bolts (2).
84942883

  1. Remove the engine oil cooler cover.
  2. Remove the engine oil cooler.
  3. Clean all sealing surfaces.
Installation Procedure
84972056

  1. Install the engine oil cooler.
  2. Apply a 2 mm (0.08 inch) bead of RTV silicone sealant, GM P/N 12346240, in the groove around the engine oil cooler cover.
  3. Install the engine oil cooler cover.
Notice: Refer to Fastener Notice in Service Precautions.
84972057

  1. Install the engine oil cooler cover bolts (2). Tighten the engine oil cooler cover bolts to 30 Nm (22 ft. lbs.).
  2. Install the engine oil cooler inlet and outlet nuts (1). Tighten the engine oil cooler inlet and outlet nuts to 20 Nm (15 ft. lbs.).
  3. Reposition the oil feed and return lines.
84942883

  1. Install the oil cooler outlet and install the oil cooler inlet lines to the engine oil cooler. Use 4 new seals.
Tighten the oil feed and return lines to 30 Nm (22 ft. lbs.).
84936658

  1. Install the water crossover:
    • Position the crossover.
    • Install the upper and lower seals (2).
    • Install the water crossover bolts (1). Tighten
Tighten the water crossover bolts to 30 Nm (22 ft. lbs.).
  1. Connect the electrical connectors at the following locations:
    • The engine coolant temperature sensor (4)
    • The engine coolant temperature sender (2)
  1. Install the intake manifold.
  2. Install the intake plenum.
  3. Raise the vehicle.
89116492

  1. Install the oil cooler outlet (1) line to the engine block. Tighten the oil cooler outlet (1) line to 30 Nm (22 ft. lbs.).
  2. Install the oil cooler inlet (2) line to the engine block. Tighten the oil cooler inlet (2) line to 30 Nm (22 ft. lbs.).
  3. Install the oil filter housing to the engine block. Tighten the oil filter housing to 45 Nm (33 ft. lbs.).
  4. Lower the vehicle.

Dec 22, 2014 | 2001 Cadillac Catera

1 Answer

Engine diagram


That is the oil cooler. Remove the oil filter. That exposes a large 'nut'. Remove the nut (and the 2 lines going in/out) and replace the oil gasket/O ring. If original oil cooler is dent or damaged, replace cooler as well. Could also just come from the lines going in and out of the cooler (put new hose clamps on).

Jan 05, 2014 | 1997 Audi A4

1 Answer

My 2001 GMC Jimmy needs to have the oil cooler lines replaced but I'm confused as to which assembly I need to get the lady at Schucks Oreillys said it's either the lines that go from the transmission to...


The oil lines going to the radiator is your transmission cooler lines, you will look for a smaller radiator and its connections, usually connected using an oil filter adapter.

Dec 13, 2013 | Cars & Trucks

3 Answers

We need to know if the radiator has an enigine oil cooler in it so we know which one to buy


if you get under the car on the driver side were the oil filter is and look were the filter screw onto the motor,if you see 2 large lines coming from the plate that the filter screws onto going to the front of the motor and attach to the lower rad then you have an engine oil cooler in the radiator.there will be lines that come from the transmission to the radiator that are considerably smaller.

Sep 16, 2011 | 1994 GMC Safari

1 Answer

Radiator replace


I Hope you Find this Helpfull And Please Remember to RATE ME

  1. Drain the coolant.
  2. Disable the SIR.
  3. Move the forwarding discriminating sensor out of the way.
  4. Remove the air cleaner assembly.
  5. Remove the cooling fans.
  6. Disconnect the radiator inlet hose from the radiator.
    1. Disconnect the radiator outlet hose from the radiator.
    2. Disconnect the engine oil cooler lines from the right radiator end tank.
    3. Disconnect the transmission oil cooler lines from the left radiator end tank.
    4. Remove the left and the right engine torque struts.
      1. Remove the upper radiator support screws.
      2. Remove the radiator from the vehicle. Lift the radiator up and out. INSTALLATION PROCEDURE
        1. Install the radiator to the vehicle.
        2. Install the upper radiator support screws. Tighten the bolts to 6 Nm (53 inch lbs.). NOTICE: Refer to Fastener Notice in Service Precautions.
        3. Install the transmission oil cooler lines to the radiator. Tighten the transmission oil cooler line fittings to 27 Nm (20 ft. lbs.).
        4. Connect the engine oil cooler lines to the radiator. Tighten the engine oil cooler lines to 18 Nm (13 ft. lbs.).
        5. Install the left and the right engine support torque struts.Connect the radiator outlet hose to the radiator.
          1. Connect the radiator inlet hose to the radiator.
          2. Install the cooling fans.
          3. Install the air cleaner assembly.
          4. Install the forward discriminating sensor.
          5. Enable the SIR.
          6. Refill the coolant.
        6. Hope this Helps and PLEASE RATE ME

Jun 03, 2009 | 1998 Cadillac DeVille

1 Answer

I need 2 know how to remove the radiator


THIS IS a 1995 LINCOLN CONTINENTAL W/4.6L ENGINE
iIBELIEVE TOWN CAR IS DIFFERENT LET ME KNOW IF SO AND PLEASE DONT FORGET TO RATE ME


REMOVAL
  1. Disconnect battery ground cable (14301).
  2. Drain engine coolant.
  3. Remove engine air cleaner (ACL) (9600).
  4. Remove upper radiator hose (8260) from water bypass tube.
  5. Remove radiator overflow hose (8075) from radiator (8005) and fan shroud (8146). NOTE: Loosen transmission oil cooler lines while securely holding radiator connector with a back-up wrench.
  6. Remove transmission oil cooler line from oil cooler inlet fitting.
  7. Remove nuts retaining A/C condenser core to the radiator.
  8. Disconnect engine control sensor wiring (12A581) from the auxiliary electric cooling fan motors and the CCRM.
  9. Raise vehicle on hoist.
  10. Remove splash shield from lower radiator support (16138) and front sub-frame (5C 145).
  11. Remove lower radiator hose (8286) from radiator. NOTE: Loosen transmission oil cooler lines while securely holding radiator connector with a back-up wrench.
  12. Remove oil transmission cooler line from oil cooler outlet fitting on radiator.
  13. Remove retaining screws for power steering/transaxle oil cooler and position cooler aside.
  14. Support fan shroud, radiator and A/C condenser core (19712) with a suitable jackstand. Remove lower radiator support. Position jackstand aside and carefully remove radiator and fan shroud.
  1. Remove two retaining bolts for fan shroud at top of radiator and remove fan shroud from radiator.
  2. Remove upper radiator hose from radiator.
INSTALLATION
  1. Follow removal procedure in reverse order.
  2. Tighten fan shroud bolts and A/C condenser core nuts to radiator to 3-5 Nm (27-44 inch lbs.) .
  3. Tighten lower radiator support bolts to 8-11 Nm (71-97 inch lbs.) .
  4. Tighten transmission oil cooler lines to fittings to 25-28 Nm (18-21 inch lbs.) .
  5. Tighten power steering/transaxle oil cooler and splash shield retaining screws securely.
  6. Refill engine coolant.

Feb 11, 2009 | 1995 Lincoln Continental

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

Jonah Oneal

Level 3 Expert

14092 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...