Replace wheel bearing
Hub and Bearing Assembly
CAUTION: Do not begin this removal procedure unless the following parts are available:
Once removed, these parts must not be reused during assembly. Their torque holding ability or retention capability is diminished during removal.
Removal
Remove and discard front axle wheel hub retainer (3B477).
Remove cotter pin from tie rod end stud and remove slotted nut. Discard cotter pin and nut.
For SHO vehicles, remove vinyl cover from upper link stud.
Remove stabilizer bar link (5K484) from front shock absorber (18124) .
If front disc brake rotor will not pull off, apply Rust Penetrant and Inhibitor D7AZ-19A501-AA or equivalent meeting Ford specification ESR-M99C56-A to inboard and outboard rotor/hub mating surfaces. Install 3-Jaw Puller 205-D027 (D80L-1013-A) or equivalent and remove front disc brake rotor by pulling on front disc brake rotor outside diameter and pushing on hub center. If excessive force is required for removal, check front disc brake rotor for lateral runout prior to installation. Refer to Section 06-00.
Item
Part Number
Description
1
204-085 (T83P-1104-BH)
Metric Hub Remover Adapter
2
204-067 (T81P-1104-A)
Front Hub Replacer
3
—
Turn Wrench Counterclockwise
4
—
Hold Wrench Stationary While Turning Other Wrench
5
204-069 (T81P-1104-C)
Front Hub Remover/Replacer
6
204-067 (T81P-1104-A)1
Two Stud Adapter
A
—
Make Sure Metric Hub Remover Adapter 204-085 (T83P-1104-BH) is Fully Threaded onto 1107 and is Positioned Opposite the Two Stud Adapter 205-237 (T86P-1104-A1)
Installation
NOTE: If bearing carrier is corroded to front wheel knuckle , apply Rust Penetrant and Inhibitor D7AZ-19A501-AA or equivalent meeting Ford specification ESR-M99C56-A to the inbI have a bad wheel bearing how do I replace it - f8656a.gifutboard wheel hub/knuckle mating surface and allow to soak.
Remove wheel hub from front wheel knuckle .
Remove all foreign material from knuckle bearing bore foI have a bad wheel bearing how do I replace it - ani_caut.gifating of new wheel hub.
Position wheel hub in front wheel knuckle . Install three new hub and bearing retaining bolts. Tighten to 83-107 Nm (61-78 lb-ft).
Install stabilizer bar link to front shock absorber . Install stabilizer bar link nut. Tighten to 77-103 Nm (57-75 lb-ft). For SHO vehicles, install stud cover.I have a bad wheel bearing how do I replace it - ani_caut.gif"h_mi">
NOTE: Remove rust from the rotor and hub mating surfaces with a medium abrasive pad.
Install front disc brake rotor and disc brake caliper . Tighten caliper anchor bracket bolts to 88-118 Nm (65-87 lb-ft).
Install front axle wheel hub retainer . Tighten to 230-275 Nm (170-203 lb-ft).
SOURCE: My car makes a bad growling noise. Everyone said
WHEEL BEARING USUALLY STARTS MAKING A ROARING TYPE NOISE WHICH USUALLY GETS LOUDER THE FASTER YOU DRIVE, SOMETIMES THEY WILL BE LOOSE , TO CHECK JACK UP THAT WHEEL AND GRAB TOP AND BOTTOM OF TIRE AND SHAKE, IF THERE IS MOVEMENT, TRY TO GET SOMEONE TO ROCK TIRE FOR YPU AND WATCH WHERE AXLE GOES INTO CENTER OF BEARING AND SEE IF AXLE IS MOVING WITH TIRE MOVEMENT AND SPINDLE REMAINS STATIONARY, THEN IT IS BAD BEARING, OR SOMETIMES THERE WILL BE NO MOVEMENT, THEN BLOCK REAR WHEELS AND RUN CAR WITH THAT WHEEL IN AIR AND SEE IF YOU HEAR NOISE, GOOD LUCK.
SOURCE: I have a saturn sl2 series 2000 I just had the
Maybe the wrong one was replaced,these are tricky sometimes it sounds like the rightside but is really the leftside or the bearing was installed wrong or the bearing is not the noise, the best way is to get it on a lift and run it in drive and try to pinpoint the noise.
SOURCE: how do i replace bad front wheel bearing ?
Replace the hub assembly which can be bought for $58 to $100 from various sources.
REMOVAL AND INSTALLATION
SOURCE: repair front wheel bearing assembly
no special tools in particular just the usual or necessary tools required.. 1stly u remove the Tyre and the caliper then u'll see something like a long rod dats the bearing
2,130 views
Usually answered in minutes!
front or back it makes a difference.
Front or back?
×