1996 Ford Ranger SuperCab Logo

Related Topics:

A
Anonymous Posted on Jan 11, 2014

1996 ford ranger power steering hoses - 1996 Ford Ranger SuperCab

4 Related Answers

junkman1249

Ricardo Loranca

  • 552 Answers
  • Posted on Dec 13, 2008

SOURCE: hoses are leaking

one at a time. after you install them make sure you turn the car on and move the steering wheel left to right several times to let the fluid circulate into the pump. you hear a strange noise but it will go away

Ad
jmassengill

Johnny Massengill

  • 345 Answers
  • Posted on Jan 04, 2009

SOURCE: power steering went out on 1996 ford ranger what is problem?

The problem could be anything from a power steering hose has leaked out all the power steering fluid or the steering rack could be leaking fluid. Has the car made any strange noises when turning the steering wheel? A car that is loosing power steering fluid will at some point lose so much fluid as to make the power steering pump cavitate (starve for fluid) and the pump will make a high pitched noise when it has too little fluid in it. I can't remember if the 1996 ranger had only one belt on the engine or if the power steering has it own seperate belt. The belt being gone would prevent the power steering from working but if you only have one belt the car would also overheat.

Anonymous

  • 3600 Answers
  • Posted on Nov 24, 2009

SOURCE: diagnose power steering problem with 1996 Ford

normally caused by the Ferrel end is worn out so hose has to be replaced.

Anonymous

  • 1 Answer
  • Posted on Mar 05, 2010

SOURCE: Ford ranger timing belt changing

My 1996 Ford Ranger, battery light came on 2 days ago. It hasn't given any other problems all winter...yesterday it died, the warmest day of the year so far. It's got 2 more years on the warranty. And the sound it makes when trying to start is a long trail of "clicks" rather than the usual single click, dead battery sound.

Right before it died yesterday, pressure to the gas peddal produced back fires until finally it died altogether. Minutes before that I noticed my indicator began to falter, blinking very slowly. Within 5min. the truck died completly.

What would electrical failures have to do with backfiring? What could be the problem(s)?

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Steering wheel sound when truning

Check for worn bearings in the power steering pump where the drive belt pulley attaches to the pump shaft.
1helpful
2answers

I have no power to my coils on a 1996 ford ranger

Did you check the fuses and relays ? You may need to get a wiring diagram to trace the circuit back to the key switch.
1helpful
1answer

Removing power steering pump from v8 windsor

Section 11-02A: Steering Pump, Power, C-II 1996 Aerostar, Ranger and Explorer Vehicles Workshop Manual REMOVAL AND INSTALLATION Pump and Pulley SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Steering Pump Pulley Remover T69L-10300-B Steering Pump Pulley Replacer T65P-3A733-C
Removal
  1. Disconnect the power steering return hose (3A713) at the pump and drain fluid.
  1. Remove the power steering pressure hose (3A719) by unscrewing connector from the pump.
  1. On the Aerostar 3.0L V-6 engine (6007), loosen the drive belt tensioner (6B209) and adjustment bolts.





    Item Part Number Description 1 10346 Generator 2 8501 Water Pump 3 8678 Belt Idler Pulley 4 3A733 Power Steering Pump Pulley 5 6303 Crankshaft 6 2884 A/C Clutch 7 — Without A/C On the 2.3L I-4 and 4.0L V-6 engines, slacken belt tension by lifting drive belt tensioner in a counterclockwise direction. On Ranger 3.0L V-6 engines, slacken belt tension by lifting drive belt tensioner in a clockwise direction. Remove drive belt (8620) from under drive belt tensioner and slowly lower pulley to stop. Remove the drive belt from the power steering pump pulley (3A733).





    Item Part Number Description 1 10346 Generator 2 2884 A/C Clutch 3 3A733 Power Steering Pump Pulley 4 8501 Water Pump 5 6303 Crankshaft 6 8678 Belt Idler Pulley 7 6B209 Drive Belt Tensioner
  1. NOTE: If the drive belt requires servicing, refer to Section 03-05 .

    Remove the drive belt from the power steering pump pulley.
  1. Remove the oil dipstick tube.
  1. Remove the power steering pump support (3C511).
  1. Install Steering Pump Pulley Remover T69L-10300-B on the pulley.
  1. NOTE: Do not apply pressure on the power steering pump rotor shaft (3B559). Pressure will damage internal thrust areas of the power steering pump (3A674).

    While holding the remover tool nut stationary with a wrench, rotate the inner spindle of the remover tool clockwise until the pulley is pulled off the power steering pump rotor shaft.
  1. Remove the bolts attaching the power steering pump to the A/C compressor mounting bracket (2882).
Installation
  1. Install the power steering pump on the A/C compressor mounting bracket. Install and tighten attaching bolts to 41-61 Nm (30-45 lb-ft). On 4.0L engine, tighten to 47-64 Nm (35-47 lb-ft).
  1. Position the support on the A/C compressor mounting bracket. Install mounting bolts and tighten to 47-64 Nm (35-47 lb-ft).
  1. NOTE: Fore/aft location of power steering pump pulley on power steering pump rotor shaft is critical. Incorrect belt alignment may cause drive belt squeal or chirp. Make sure pull-off groove on power steering pump pulley is facing front and flush with end of shaft ± 0.254mm (± 0.010 inch).

    Install the Steering Pump Pulley Replacer T65P-3A733-C and install the power steering pump pulley.
  1. Install the drive belt on the power steering pump pulley.
  1. On the 2.3L I-4, Ranger 3.0L V-6, and 4.0L V-6 engines, position and rotate drive belt on engine. While lifting drive belt tensioner in a counterclockwise direction (clockwise on Ranger 3.0L V-6), slide drive belt under drive belt tensioner and lower drive belt tensioner to drive belt.
    On Aerostar 3.0L V-6 engine, position the belt idler pulley (8678) assembly to give the drive belt the tension specified. Refer to belt tension check in Section 03-05 . Tighten the drive belt tensioner and adjustment bolts to 47-64 Nm (35-47 lb-ft).
  1. Install the power steering pump support, if removed.
  1. Install the oil dipstick tube.
  1. Install the pressure hose tube nut and new Teflon® wagner into power steering pump valve outlet fitting (3D654) and tighten to 41-54 Nm (30-40 lb-ft).
  1. Connect the power steering return hose to the power steering pump, and reposition the clamp.
  1. Fill the power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent fluid meeting specification ESW-M2C33-F. Start the engine and turn the steering wheel (3600) from left to right without hitting stops to remove air from the system.
  1. Check for leaks and recheck the fluid level. Add fluid if necessary to proper level as specified in Section 11-00 .


    Power Steering Pump and Power Steering Pulley, 2.3L TPH Engine, Ranger Only





    Item Part Number Description 1 2882 A/C Compressor Mounting Bracket 2 N606543-S2 Bolt (2 Req'd) 3 N606069-S2 Bolt (2 Req'd) 4 N605803-S2 Bolt 5 N800199-S8M Screw 6 3D673 Power Steering Pump Pulley 7 3F671 Power Steering Belt Idler Support 8 N806020-S2 Bolt 9 3A674 Power Steering Pump 10 19703 A/C Compressor A — Tighten to 21.2-29 Nm (16-21 Lb-Ft) B — Tighten to 40.3-55 Nm (30-41 Lb-Ft) C — Tighten to 44-51 Nm
    (32-38 Lb-Ft)

    Power Steering Pump and Power Steering Pulley, 3.0L Engine, Aerostar





    Item Part Number Description 1 3A674 Power Steering Pump 2 3C511 Power Steering Pump Support 3 6007 Engine 4 N803564 Stud 5 N802827-S2 Nut 6 N800199-S8M Screw (3 Req'd) 7 N8011179-S2 Screw (3 Req'd) 8
0helpful
1answer

Power steering problems on 1996 Ford Ranger 2WD

Repair or replace the rotary valve in the steering box.
0helpful
1answer

1996 Ford Ranger horn, cruise control and 4W drive not working

for the horn and cruise control you may need a new clockspring. pull the steering wheel and make sure it is not broken.
0helpful
1answer
1helpful
2answers

Power steering went out on 1996 ford ranger what is problem?

The problem could be anything from a power steering hose has leaked out all the power steering fluid or the steering rack could be leaking fluid. Has the car made any strange noises when turning the steering wheel? A car that is loosing power steering fluid will at some point lose so much fluid as to make the power steering pump cavitate (starve for fluid) and the pump will make a high pitched noise when it has too little fluid in it. I can't remember if the 1996 ranger had only one belt on the engine or if the power steering has it own seperate belt. The belt being gone would prevent the power steering from working but if you only have one belt the car would also overheat.
0helpful
1answer

Hoses are leaking

one at a time. after you install them make sure you turn the car on and move the steering wheel left to right several times to let the fluid circulate into the pump. you hear a strange noise but it will go away
0helpful
1answer

Where is the power steering sensor located on a 1993 ford ranger 4.0 super cab? (or is it called the power steering pressure switch?)

The power steering pressure switch as its called threads in to the power steering pressure hose most of the time it is close to the power steering pump, I have also seen them at the lower point of the pressure hose close to the rack and pinion.
Not finding what you are looking for?

100 views

Ask a Question

Usually answered in minutes!

Top Ford Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

xxxxxx xxx

Level 3 Expert

5117 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...