'96 Chevy Monte Carlo- codes P0441 and P1655

DTC P1655 Evaporative Emission (EVAP) Purge Solenoid Control Circuit !
Output Driver Modules (ODMs) are used by the PCM to turn on many of the current-driven devices that are needed to control various engine and Transaxle functions. Each ODM is capable of controlling up to 7 separate outputs by applying ground to the device which the PCM is commanding on. Unlike the Quad Driver Modules (QDMs) used in prior model years, ODMs have the capability of diagnosing each output circuit individually. DTC P1655 set indicates an improper voltage level has been detected on ODM B output 5, which controls the EVAP purge solenoid.
You could have a wiring problem ,or the purge solenoid or the driver in the PCM ! More then likely it's the EVAP purge solenoid !
Purge Control Solenoid Valve

EVAP solenoid control circuit YouTube

well most evap solenoids are either on the back by fuel tank, by differential, or infront by firewall or wheel fender wells which need a lil dissasembly. probably a vacum leak first check ure gas cap that it actually locks and reset code if comes back either a leak to the solenoid or bad connector corrosion maybe.

If the code is 301 it means there is no power from that cylinder. It could be a problem with the ignition, fuel injector, or something mechanical.

Huh??? If there is a code P1655 then tere IS a DTC! DTC means Diagnostic Test Code. The DTC you have is P1655. So, I am not sure exactly what you are trying to say here.

DTC P1655 is a "Vehicle Specific" code. The only way to know for sure what the problem is, would be to look the code up based on the specific Year, Make, Model and Engine Size of the vehicle we are talking about.

For MOST GM vehicles, the code description is P1655 "EVAP Purge Solenoid Control Circuit".

I can't verify this without knowing what you are working on and cannot give yopu any specifics on how to repair it for the same reason.

P0341: Its a Camshaft Position Sensor (CPS) $30 to $40
P0441: Evaporative Emission Control System Incorrect Purge Flow.
P1655: Evaporative Purge Solenoid Control Circuit. $18 to $24

Looks like you have an Emission problem and if you buy the parts and put them your self, Then it will be cheaper. Good luck

http://www.obd-codes.com/p0441

The PO441 has to do with your HO2S 2 (Oxygen sensor). You need to check to make sure the wire is not off of the sensor and check the grounds to the Oxygen sensor. Could be a bad Oxygen Sensor. The other code has to do with your Evap system Purge solenoid circuit. Has to do with detecting an improper voltage level. Could be a shorted Purge solenoid.

Error Code: P0441
Fault Location:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Evaporative Emission (EVAP) Canister Purge Regulator Valve faulty/jammed.
Evaporative Emission (EVAP) Canister Purge Solenoid Valve faulty/jammed.
Evaporative Emission (EVAP) Canister Sealing faulty.
Pipes between Tank Breathing and Throttle Body leaky/blocked.
Hose connection(s).
Intake leak.
Possible Solutions:
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Perform Output Test.
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve.
Check Evaporative Emission (EVAP) Canister.
Perform Basic Setting.
Check Pipes between Tank Breathing and Throttle Body.
VSV connector near air filter box disconnected.

THESE ARE FROM THE GM CODE DIFINITION MANUAL, U NEED TO TAKE THIS TO THE DELAER, U HAVE SOME SERIOUS PROBLEMS TO GIVE THIS MANY CODES.

P0300 - Engine Random Misfire Detected
P0441 - Evaporative Emission Control System Incorrect Purge Flow
P0705 - Trans Range Switch Circuit
P1106 - Manifold Absolute Pressure (MAP) Sensor Circuit Intermittent High Voltage
P1133 - Heated Oxygen Sensor (HO2S) Insufficient Switching Bank 1 Sensor 1
P1441 - Evaporative Emission (EVAP) System Flow During Non-Purge
P1662 - Cruise Lamp Control Circuit
P1672 - Low Engine Oil Level Lamp Control Circuit
P1870 - Transmission Component Slipping