1994 Toyota Camry Logo

Related Topics:

Anonymous Posted on Jan 06, 2018

Adjusting a power window regulator.

Can you adjust a power window regulator on a 1994 toyota camry? My window goes down but it won't go back up, only with a little help when i push it up will it go up. I can here the motor trying when i do this. On some photos i seen it looks like there is way to adjust the wire pulley. Any suggestions?

  • Anonymous May 09, 2009

    MY WIFE CAR BOTH REAR WINDOWS DONT WORK TOYOTA CAMRY LE 1996

×

1 Answer

obsteiner

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • Toyota Master 901 Answers
  • Posted on Jan 06, 2018
obsteiner
Toyota Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: May 03, 2009
Answers
901
Questions
1
Helped
303212
Points
7223

The motor needs replacing not adjusting. If you can help the window do up and it stops at the top, it's 'adjusted' properly.
You could pull the door panel and maybe lube the motor/drive and cables. It might work a year or a day.
But while you have the door panel off why not just put in a whole new unit. It's just as much trouble to 'fix' it as it is to replace it.
You could limp thru by spraying some silicone in the window track.

5 Related Answers

shaggyrat

Christophe Thompson

  • 1224 Answers
  • Posted on May 31, 2008

SOURCE: Window on camry won't stay up.

there is a bar that runs with the gear arms about half the length of the door in which the glass sits in on the track there are a couple
96d50ab.jpg tabs that hold the glass in so the window dont slip out if your missing these tabs the window will fall down from vibration or just timely wareing down
the way to get at the window track is by removing the door panel accessing the window area behind metal door and replaceing tabs or if newer silicone that was used in its place
you will need a door panel remover tool that looks like a snakes tounge but bigger this is to pop the door panels clips with out damaging the clips or door panel

http://images.google.com/imgres?imgurl=http://www.blueridgemiataclub.org/technical/windows/images/Image12.jpg&imgrefurl=http://www.blueridgemiataclub.org/technical/windows/index.htm&h=450&w=600&sz=34&hl=en&start=1&um=1&tbnid=v-4tIVhDp79sMM:&tbnh=101&tbnw=135&prev=/images%3Fq%3Dauto%2Belectric%2Bpower%2Bwindows%2Btrack%26um%3D1%26hl%3Den%26safe%3Doff

heres a link of same proceedure but different vehicle that i decribed how to access the window area hope this was helpful
if you dont want to pursue doing the window your self you can always call a windshield and glass repair shop they can come out and mount your window for you at a price i dont know how much where your at in the world

Ad
motor1258

Mike Butler

  • 6674 Answers
  • Posted on Jan 21, 2009

SOURCE: Correct Firing Order for 1994 Toyota Camry 2.2L 4 cyl.

1-3-4-2

idare_ya

  • 95 Answers
  • Posted on Jan 23, 2009

SOURCE: 1994 Camry wagon, passenger side electric window.(front seat)

Can you hear the moter or do interior lights dim when pressing button? If so remove door panel and lubricate tracks and rolers using lithium grease lube only the tracks that do not come in contact with glass.

Check the connections at the switch and at the moter with a volt meter if there is power than time for a new moter. no power than check at drivers side switch. If no power there and fuse is ok you have a open in wires and will have to trace entire circut

Anonymous

  • 21 Answers
  • Posted on Apr 04, 2009

SOURCE: I need to change the belt on 2003 Toyota Camry.

you should have a belt diagram on the front cross member of the vehicle under the hood that tells you how to do the job need

Anonymous

  • 131 Answers
  • Posted on Apr 18, 2009

SOURCE: window motor fuse location on 92 toyota camry le

look behind the money chance container l side lower dash

g gl

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

What is the torque specs for a tie rod end on a 1994 toyota camry

The tie rod end adjusting nut, 54 ft lb or 74 Nm
The tie rod end ball joint nut, 36 ft lb or 49 Nm
0helpful
1answer

Replaced Window Regulator, Works but when going up least a gap and doesnt close right

you have to make sure the alignment is correct when fitting new regulator, they leave around 5mm adjustment on the securing bolts to adjust the window, check these and refit always check before fitting door card etc. also on so models there is and adjuster on the arm that will need setting as well as this is angle alignment.
1helpful
1answer

I have a 1994 Toyota Camry and the power window on the passenger side has gone down, under power. Then nothing would happen when I would pulled up on the switch on the driver side main switch and the also...

more than likely one of the switches are bad (down side of switch works but up side of switch dont) being as the switches are wired together if one goes bad other one won't work either take the switch out one of back doors should be same as front passenger door put rear switch in front passenger door if works then u know front door switch is bad if it doesn't then drivers door switch is bad
u replaced window regulator Did that come with motor too??? if not check to see if motor is good
there is two wires going to motor cut isolation back on wires and using some jumper wires attach one wire to positive terminal of a 12 volt battery attach other wire to negative terminal of battery window should move up or down reverse connections and window should move other way
0helpful
1answer

1994 Camry: 1998 Toyota camry power window fell in door...

your problem is damage window regulator, you can change it by removing the trimboard first to give way in removing the old window regulator assembly.
0helpful
1answer

Driver side window wont roll up??? 1994 Toyota Camry

that model camry has a window regulator that is cable driven. it is very common for that cable to snap and not allow the window to close. it will likely need a window motor/regulator assembly.
0helpful
1answer

1994 toyota camry window stalling

the motor is getting weak. need to replace it and while your there check the regulator and the rubber seal that the glass slides in. they will get dirt in the groves and cause glass to stick. spray a lubricate in the rubber slots and try it .
2helpful
1answer

1994 toyota camry driverside power window

Yes, it is the regulator. The wire cable that runs the window up and down is broken.

Hope this helps; thanks for choosing FixYa.
0helpful
1answer

1994 toyota camry window clicking

The 2" diameter white pulley is part of the regulator. That is what the cable rides on to raise & lower the window, and it is critical to the operation of the window. Replace the regulator assembly.
9helpful
3answers

1994 Toyota Camry window regulator

This video will show you how to take the old one out and how to put the new one in.">
Not finding what you are looking for?

438 views

Ask a Question

Usually answered in minutes!

Top Toyota Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

926 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...