Need to calibrate the wiper motor - 2007 Mitsubishi Eclipse

You have to reinstall the wipers when the motor is at park.if the splines don't match up then you have to adjust the transmission assembly

did you mark wiper motor arms and wiperarms shaft for reassembly sound like something not back in the right location.

OK got your message on the other post (About the van) I am assuming that your Voyager is equipped with Automatic Climate Control. Follow the instructions below and you will get a better idea of what is wrong with your system.

Calibration/Diagnostics
1. To enter calibration/diagnostics test, set parking brake. Start and warm engine to normal operating temperature. With engine idling, turn blower switch to high. Turn mode switch to panel. Open all outlets. Move temperature to full cold.
2. Press and hold rear wash and rear wiper buttons simultaneously for 5 seconds (Until ALL LEDs illuminate). All LEDs should illuminate for 5 seconds. Rear wiper and intermittent rear wiper button LEDs will flash alternately during calibration/diagnostics test.
3. After approximately 60 seconds, if only the rear wiper button LED is flashing, calibration is successful and the system is okay. If rear wiper and intermittent rear wiper button LEDs are flashing, Diagnostic Trouble Codes (DTCs) are present. (See "Reading Diagnostic Codes" below)
4. To exit calibration/diagnostics test at any time, press the rear window defogger button, rear wiper button, or cycle the ignition off and then on. Test will automatically terminate 15 minutes after calibration/diagnostics is entered.

Reading Diagnostic Codes
1. Perform calibration/diagnostics test. If a DTC is present after calibration/diagnostics test has been performed, system will flash rear wiper and intermittent rear wiper button LEDs in sequence. Rear wiper represents code level, and intermittent rear wiper button LED represents code value.
2. Each time the rear wash button is depressed, rear wiper button LED wil cycle to the next code level in numeric sequence. After code level 5 is reached, rear wiper button LED will cycle back to code level 1. See table below.

What has most likely happened is that the Heater-a/c unit needs to be recalibrated and here are the steps to do so.
With the engine running and fully warmed up, A/C has to be turned off for at least 5 minutes [don't turn it on at all] and transmission in Park do the following
1. Set the temp control all the way to cold
2. Set the mode selector to Vent so air blows out of the dash panel outlets.
3. Hold down the rear washer button and the rear wiper buttons simultaineously for about 5 seconds until most all of the heater and ac panel lights blink and then release both buttons
6. At this point the system should go into a self calibration test which can take up to 60 seconds. While it is calibrating various control panel switch lights will blink as it goes through it's tests.
7. When the system is done calibrating then just the rear wiper light should be flashing and you can exit the test by turning off the vehicle. Wait about 10 seconds and restart the engine and it should be fine. If both the rear wiper and intermittent light are both still flashing after the calibration then there is most likely a problem with the system that will need more diagnosing. I see this fairly often with battery replacements so I think you'll be ok. It sometimes takes a couple of tries to calibrate so don't give up if it doesn't work the first time. Good luck, hope this helps!

do this calibration reset, it will usually rest he lights and the ac will work again, if it doesn't reset you have a part failure and the dealer you need to hook a Chrysler scan tool to diagnose the problem.

CALIBRATION/DIAGNOSTICS TEST ENTRY
TO INITIATE TESTS:
Set Blower motor ON HIGH
Set Mode position to Panel
Set Temperature to Cold (Both slide pots if equipped)
Depress WASH and REAR WIPER button simultaneously for 5 Seconds (Until all LED's light)
RESULTS:
All LED's will turn on for 5 Seconds
Calibration Test is running when REAR WIPER and INTERMITTENT are alternately flashing. Cooldown test is running if A/C and RECIRC are alternately flashing.
Acceptable results is REAR WIPER LED is the only LED flashing. Push Rear Wiper to exit.
After all tests have passed, Calibration Diagnostics and Cooldown can be run separately

That has to do with your computer for your body controls, such a/c, heater, wipers, etc...
Most common problem is drinks spilling into the computer which is right between the cup holder. It will eventually cause a problem with a/c most likely.

Hold the rear wiper button and the rear wiper wash buton for like 4-5 sec and it will start its calibration i think you need the blower on hi and the temperature knob at cold

a/c control module or a/c relay fuse.

the climate control panel has come out of calibration..
to re-calibrate it you need to have
Set Blower motor ON HIGH
Set Mode position to Panel
Open all A/C outlets
Set Temperature to Cold (Both slide pots if equipped)
Depress WASH and REAR WIPER button simultaneously for 5 Seconds (Until all LED's light)

All LED's will turn on for 5 Seconds
When done REAR WIPER LED is the only LED flashing. Push Rear Wiper to exit

your a/c system must be functioning properly for it to re-calibrate.

Sounds like the HVAC control head needs to be recalibrated. The procedure is fairly easy, Heres how its done:

CALIBRATION/DIAGNOSTICS TEST ENTRY
TO INITIATE TESTS:
Set Blower motor ON HIGH
Set Mode position to Panel
Set Temperature to Cold (Both slide pots if equipped)
Depress WASH and REAR WIPER button simultaneously for 5 Seconds (Until all LED's light)
RESULTS:
All LED's will turn on for 5 Seconds
Calibration Test is running when REAR WIPER and INTERMITTENT are alternately flashing. Cooldown test is running if A/C and RECIRC are alternately flashing.
Acceptable results is REAR WIPER LED is the only LED flashing. Push Rear Wiper to exit.
After all tests have passed, Calibration Diagnostics and Cooldown can be run separately.

After that the lights should go out and everything should work properly as long as everything is in proper working order.

Good Luck