Location of camshaft position sensor on 2009 saturn aura

XR Transmission Fluid Change-Drain Plug Location

SaturnFans.com http://www.saturnfans.com > ... > Aura General
Mar 17, 2009 · 1 post
Hi, I'm looking to drain and change the fluid on the 6T70 but I can't seem to locate what looks like an obvious drain plug.
Where to take my Saturn Aura for transmission fluid ...
Jun 28, 2012
automatic transmission fluid service 3.5L V6 - SaturnFans.com
Dec 19, 2011
Do you need to drop the transmission to change the filter on a ...
Jul 23, 2018
How to fill tranny fluid with the 3.5 - SaturnFans.com Forums
Aug 13, 2009
More results from www.saturnfans.com

How to change the transmission fluid on a 2008 saturn aura

JustAnswer https://www.justanswer.com > Saturn Repair
Sep 21, 2012 - Hello I will help you with your question,. The fluid procedure for the 6 speed is shown below, look this over and let me know how I can help ...
1 answer · Top answer: Glad to help and please let me know if you have further questions Thank you

Saturn Aura Transmission Fluid Change Cost Estimate

RepairPal https://repairpal.com > estimator > transmission-fluid-c...
The average cost for a Saturn Aura Transmission Fluid Change is between $181 and $208. · RepairPal Certified shops offer a 12-month/12,000 mile service warranty ... Videos

https://www.google.com/search?q=2008+Saturn+Aura+XR++transmission+fluid+change

Question edited for clarity.
Question moved to model category.

https://www.google.com/search?q=2009+saturn+aura+tcm+location

..

(1) Camshaft Position (CMP) Actuator Solenoid - Intake Bank 1
(2) Camshaft Position (CMP) Sensor - Intake Bank 1
(3) Camshaft Position (CMP) Sensor - Intake Bank 2
(4) Camshaft Position (CMP) Actuator Solenoid - Intake Bank 2
(5) Camshaft Position (CMP) Actuator Solenoid - Exhaust Bank 2
(6) Camshaft Position (CMP) Sensor - Exhaust Bank 2
(7) Generator
(8) A/C Compressor Clutch
(9) Camshaft Position (CMP) Actuator Solenoid - Exhaust Bank 1
(10) Camshaft Position (CMP) Sensor - Exhaust Bank 1

That sensor is not fused.

Who told you , was it checked for DTC'S - diagnostic trouble codes ? Rather then just replacing parts why don't you take it to a qualified repair shop . Besides , the new module need's Programming and Setup , and a factory scan tool to do it .
Steering Position Sensor Calibration
Install the scan tool.
Turn ON the ignition, with the engine OFF.
Center the steering wheel.
With the scan tool select Special Functions.
Select Steering Position Sensor Calibration and press the Enter key. The scan tool screen will flash Calibration in Progress then display Calibration Complete.
Press the exit key.
Use the scan tool in order to clear any EPS DTCs.

Which engine ? This vehicle had option of six different engines , 2.4 , 3.5 , 2.8 , 3.0 , 3.2 , 3.6 And are you picking on the right part ? What code > DTC P0010: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit

DTC P0013: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit
It may not even be a cam sensor problem !
DTC P0340: Intake CMP Sensor Circuit

DTC P0365: Exhaust Camshaft Position (CMP) Sensor Circuit
DTC P0341: Intake Camshaft Position (CMP) Sensor Performance

DTC P0366: Exhaust Camshaft Position (CMP) Sensor Performance
Camshaft Position (CMP) Actuator System
The camshaft position (CMP) actuator system is an electro-hydraulic operated device used for a variety of engine performance and operational enhancements. These enhancements include lower emission output through exhaust gas dilution of the intake charge in the combustion chamber, a broader engine torque range, and improved fuel economy. The CMP actuator system accomplishes this by changing the angle or timing of the camshaft relative to the crankshaft position. The CMP actuator simply allows earlier or later intake and exhaust valve opening during the four stroke engine cycle. The CMP actuator cannot vary the duration of valve opening, or the valve lift.
During engine OFF, engine idling conditions, and engine shutdown, the camshaft actuator is held in the Park position. Internal to the CMP actuator assembly is a return spring and a locking pin. During non-phasing modes of the camshaft, the return spring rotates the camshaft back to the Park position, and the locking pin retains the CMP actuator sprocket to the camshaft


It may

I'm not an expert on the Aura, but most Saturn engines have the knock sensor on the back of the engine near the firewall. It'll be almost right in the middle.

2006 Saturn Ion Camshaft position sensor location:
The camshaft position sensor is located in the top left side of the valve cover.

what engine size 2.4L 3.5L or 3.6L.

okay there are a few things that need to be checked here, seems like you were testing the wrong things, lets start with the po300, this code is for a misfire a random one which means any cylinder at a certain time has misfired which is due to the next two codes listed, the po014 which is the exhasut camshaft postion sensor system performance and the po201 injecotr control circuit for cylinder #1.

Have the injector ohm ed and the connection and wiring checked, this problem may be a bad injector or wiring to cyl # 1 and the cam sensor needs to be tested also on bank 1exhaust side. good day