Check engine light on in our 2005 Jeep Liberty

2003 Jeep Liberty- Reading Engine / Diagnostic Codes ...

? 1:13
https://www.youtube.com/watch?v=pGrPBBzp7wE
Jan 6, 2013 - Uploaded by DeathScouter
2003 Jeep Liberty- Reading Engine / Diagnostic Codes ..... error code will flash 2 times, brief pause, flash 1 time, pause, flash 5times, pause, ...

2005 Jeep Liberty possible cause of P0442 error. - YouTube

? 5:26
https://www.youtube.com/watch?v=2ba-gH0gadg
Dec 21, 2014 - Uploaded by TheBGravit
While replacing a bad fuel pump I believe I found the cause of a P0442 Error code. I was able to repair the ...

Jeep Liberty Questions - Cylinder Misfire code - CarGurus

www.cargurus.com > Questions > Jeep > Liberty

CarGurusMay 27, 2009 - My jeep Liberty 2009 does the same the Dashboard showed a code of cylinder .... i have a jeep liberty 2006 with the # 5 cylinder misfire. i replaced the sparks... I have a 2005 Jeep Liberty 6 cylinder, engine light came on scaned the ... 2002 jeep liberty camshaft posistion sensor error code p0340 5 answers.

Check Engine Light/Misfire Due to Intake Valve Locks ...

repairpal.com > Problems > Jeep > Liberty

Recently got a second hand 2005 Jeep Liberty Sport. Everything worked fine ... #5intake valve seat dropped and held open the intake valve. 2008 Jeep Liberty.

OBD-II Trouble Code: P0305 Cylinder 5 Five Misfire Detected

www.obd-codes.com/p0305

Check Engine Light/Misfire Due to Intake Valve Locks ...

repairpal.com > Problems > Jeep > Liberty

Jeep Liberty Check Engine Light/Misfire Due to Intake Valve Locks/Valves. ...Misfire cyc 4 and random cyc misfires, changed coil packs and plugs... sounds as if rod ... Light came on again (misfire on cylinder 4) - switched coil from 4 to 2. Light ...

Jeep Liberty Questions - Cylinder Misfire code - CarGurus

www.cargurus.com > Questions > Jeep > Liberty

CarGurusMay 27, 2009 - #4 misfire new plugs and coil pack on #4 light came back on after 300 miles if ... How come it stopped misfiring for 2-3 months, and now is back? ... I have a 2005 Jeep Liberty 6 cylinder, engine light came on scaned the codes ...

Liberty Cylinder Misfire / Computer issue? - JeepForum.com

Immobiliser fault, disconnect battery from poss terminal for 15 seconds, reconnect battery close hood and doors lock car with fob wait 20 seconds open car and start car.

this is due to a bad bulb socket. they are prone to fail due to melting inside.

oil check oil. when light on dash comes on that means your jeep has a code for ya. take to auto zone and they will read the code for free with a code reader.

first, though you mentioned no oil leaking, is there oil in the engine?
Next, if engine runs well and is not ticking or tapping, have the codes checked...most larger parts stores do this free. Once you have the stored codes you can look up what system is malfunctioning.
If engine is making any noise at all or there is no oil in it, DO NOT START OR DRIVE IT...make sure whoever did the oil change knows about this now...If someone forgot to put oil in, they may be buying you a new engine!
At this point it may be something simple but can also be very serious.(hope not)
good luck

Yes ,it would set a code,a obd2 reader can confirm your problem.

recheck the oil on the dip stick. look for any leaks that you were not aware of. make sure your car is on level ground when you check the oil and mwke sure the oil is warm before you also make sure the engine is off this will give you true reading and the oil will settle when is warm

2003 3.7 Liberty check engine light for crank....what? sensor? You have scanned it?

Did this happen overnight or was it a gradual loss? Did you do any kind of repair before you lost the gas mialage? Is there a check engine light on or did it come on and go off? Did anything weird happen before the jeep got bad gas mileage? It's hard to diagnose a problem like this without actually touching the car.
Any other info might help me steer you in the right direction.