I have recently change timing belt 2000 Pajero NM 3.5 pertrol V6. Crankshoft and bank 2 timing marks are perfectly align but not sure about bank 2. the mark is not clear. can someone tell me how I can make sure bank 1 the driverside mark is correct. Can someone tell me how many notches of time belt between bank 1 and bank 2 timing marks are?

yet again
no car body stated, an ISUZU WHAT?> is this too much to ask?
no country,
no year stated,
and the poster dont know all books are indexed by...
drum roll, country model, then year., (all 3 missing, is this fun?)
and this engine, is twin cam.. the correct name is
6ve1 99 to 2004? is 3.5L
the early 2 cam is called 6VD1W (w= 4 cams total)
1998 to 2002 on usa spec troopers (guess #2)
the 2 cams in one head are gear driving side by side,
we have posted this answer on this forum over 5 times
search much>?

did i guess right? so now ill post again this data. using online official sources, not rag books.
photos posted yet again, here we go, the hard way, guessing the freakn car,.. wow.
called the VIN V engine. here.USA>







and the words

1. Verify that the sprocket timing marks are still aligned and that the groove and the keyway on the crankshaft timing sprocket align with the mark on the oil pump. The white pointers on the camshaft timing sprockets should align with the dots on the front plate.
2. Install the timing belt. Use clips to secure the belt onto each sprocket until the installation is complete. Align the dotted marks on the timing belt with the timing mark opposite the groove on the crankshaft sprocket. NOTE The arrows on the timing belt must follow the belt's direction of rotation. The manufacturer's trademark on the belt's spine should be readable left-to-right when the belt is installed.
3. Align the white line on the timing belt with the alignment mark on the right bank camshaft timing pulley. Secure the belt with a clip. WARNING If any binding is felt when adjusting the timing belt tension by turning the crankshaft, STOP turning the engine, because the pistons may be hitting the valves.
4. Rotate the crankshaft counterclockwise to remove the slack between the crankshaft sprocket and the right camshaft timing belt sprocket.
5. Install the belt around the water pump pulley.
6. Install the belt on the idler pulley.
7. Align the white alignment mark on the timing belt with the alignment mark on the left bank camshaft timing belt sprocket.
8. Install the crankshaft pulley and tighten the center bolt by hand. Rotate the crankshaft pulley clockwise to give slack between the crankshaft timing belt pulley and the right bank camshaft timing belt pulley.
9. Insert a 1.4mm piece of wire through the hole in the pusher to hold the rod in. Install the pusher assembly while pushing the tension pulley toward the belt.
10. Pull the pin out from the pusher to release the rod.
11. Remove the clamps from the sprockets. Rotate the crankshaft pulley clockwise 2 turns. Measure the rod protrusion to ensure it is between 0.16-0.24 in. (4-6mm).
12. If the tensioner pulley bracket pivot bolt was removed, tighten it to 31 ft. lbs. (42 Nm).
13. Tighten the pusher bolts to 14 ft. lbs. (19 Nm).
14. Remove the crankshaft pulley. Install the lower and upper timing belt covers and tighten their bolts to 12 ft. lbs. (17 Nm).
15. Fit the oil cooler hose onto the timing cover and tighten its mounting bracket bolts to 16 ft. lbs. (22 Nm).
16. Install the crankshaft pulley and tighten the pulley bolt to 123 ft. lbs. (167 Nm).
17. Install fan pulley assembly and tighten the bolts to 16 ft. lbs. (22 Nm).
18. Install and adjust the accessory drive belts.
19. Install the cooling fan assembly and tighten the bolts to 72 inch lbs. (8 Nm).
20. Install the upper fan shroud.
21. Install the air cleaner assembly and intake air duct.
22. Connect the negative battery cable

and wants head torque too, need egg in your beer?

There is a Toyota Technical Service Bulletin issued for this:-
T-SB-0291-08 September 11, 2008 2GR-FE Valve Timing

Procedure Service Category Engine/Hybrid System Section Engine Mechanical Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2005 - 2009 Avalon 2007 - 2009 Camry VDS(s): BK46K 2008 - 2009 Highlander 2006 - 2009 RAV4 Engine(s): 2GR VDS(s): BK31V, BK32V, BK33V, BK34V, ZK31V, ZK32V, ZK33V, ZK34V, ZK35V 2007 - 2009 Sienna Introduction This service bulletin provides information regarding valve timing inspection and service guidelines for vehicles equipped with 2GR-FE engines. © 2008 Toyota Motor Sales, USA Page 1 of 5 T-SB-0291-08 September 11, 2008 Page 2 of 5 2GR-FE Valve Timing Procedure Introduction (Continued) Figure 1. 3 2 1 5 9 8 7 6 4 1 RH Bank Intake Camshaft Timing Gear 2 RH Bank Exhaust Camshaft Timing Gear 3 RH Bank No. 2 Timing Chain 4 Crankshaft 5 Idler Gear 6 Timing Chain 7 LH Bank No. 2 Timing Chain 8 LH Bank Exhaust Camshaft Timing Gear 9 LH Bank Intake Camshaft Timing Gear Warranty Information OP CODE DESCRIPTION TIME OFP T1 T2 N/A Not Applicable to Warranty © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 3 of 5 2GR-FE Valve Timing Procedure Inspection 1. Set the No. 1 cylinder to TDC/compression. A. Set the timing mark to 0 on the timing chain cover by rotating the crankshaft clockwise. B. Verify the timing marks on the camshaft timing gears are in general alignment with the timing marks of the camshaft bearing cap: TIMING MARK IDENTIFICATION CYLINDER BANK INTAKE GEAR MARK EXHAUST GEAR MARK RH Bank (Bank 1) Small Mark Single Line LH Bank (Bank 2) Large Mark Double Line HINT When the engine is correctly timed, the timing marks will NOT perfectly align. Figure 2. Figure 3. RH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 4. RH Bank Intake Camshaft Timing Gear 2 1 1 Bearing Cap Timing Mark 2 Gear Timing Mark © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 4 of 5 2GR-FE Valve Timing Procedure Inspection (Continued) Figure 5. LH Bank Intake Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 6. LH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark HINT If the timing marks appear vastly out of alignment, turn the crankshaft one revolution (360 ) clockwise and note the position of the timing marks. Component Removal Guidelines 1. If engine disassembly is required that involves removing the camshafts or timing gears, set the #1 cylinder to TDC compression, wipe away any oil, and mark the following items in relation to each other prior to disassembly: • Timing gears • Timing chain • Timing chain No. 2 NOTE This relationship MUST be maintained. The intake gear is timed in relation to the crankshaft via the timing chain; the exhaust gear is timed in relation to the intake gear via the No. 2 timing chain. © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 5 of 5 2GR-FE Valve Timing Procedure Component Removal Guidelines (Continued) 2. If NEW camshaft timing gears or the No. 2 timing chain are being installed, the two yellow links on the No. 2 timing chain can be used to ensure correct relationship between the intake timing gear and the exhaust timing gear. Figure 7. 1 1 Yellow Link A. Align the paint mark on the timing chain with the intake gear timing mark (to ensure the intake gear is correctly timed to the crankshaft). Figure 8. RH Bank and LH Bank 3 3 4 3 3 4 5 4 5 4 1 2 1 RH Bank 2 LH Bank 3 Yellow Link 4 Gear Timing Mark 5 Timing Chain Paint Mark B. Align the two yellow links on the No. 2 timing chain to the timing marks on

no year(94-present) stated. and under kia dont help much.

its at alldtata.com, i read all the steps and not skip one, I WOULD.

wild guess, #1 a 2005 RAV4
2.0L 3sfe. inline 4 cylinder, not V6


here is the one i see on the FSM.

my gates belts all come with a manual. RTM?
if you buy the belt at a dealer they assume you have the FSM.
right?
FSM, install, steps

1. Install the oil pump pulley. Tighten the nut to 18 ft. lbs. (24 Nm).
2. Install the crankshaft timing pulley. Align the pulley set key with the key groove of the pulley. Slide on the pulley facing the flange side inward.
3. Install the No. 2 idler pulley and tighten the mounting bolt to 31 ft. lbs. (42 Nm). Be sure that the pulley moves smoothly.
4. Install the No. 1 idler pulley with the bolt and the tension spring. Pry the pulley toward the left as far as it will go and tighten the bolt. Make sure that the pulley moves smoothly.
5. Temporarily install the timing belt. Using the crankshaft pulley bolt, turn the crankshaft and position the key groove of the crankshaft timing pulley upward. If reusing the timing belt, align the points marked during removal.
6. Install the timing belt on the crankshaft timing pulley, oil pump pulley, No. 1 idler pulley, water pump pulley and the No. 2 idler pulley.
7. Install the timing belt guide.
8. Install the lower (No. 1) timing belt cover and new gasket with the 4 bolts.
9. Align the crankshaft pulley set key with the pulley key groove. Temporarily install the crankshaft pulley and bolt.
10. Align the camshaft knock pin with the groove of the pulley, and slide the timing pulley onto the camshaft with the plate washer and set bolt.
11. Tighten the pulley set bolt to 40 ft. lbs. (54 Nm).
12. Turn the crankshaft pulley and align the 0 mark on the lower (No. 1) timing belt cover.
13. Finish installing the timing belt and check the valve timing, as follows:
    1. If reusing the old timing belt, align the matchmarks made previously and install the timing belt onto the camshaft pulley.
    2. Align the marks on the timing belt with the marks on the camshaft pulley.
    3. Loosen the No. 1 idler pulley set bolt 1 / 2 turn.
    4. Turn the crankshaft pulley 2 complete revolutions TDC to TDC. ALWAYS turn the crankshaft CLOCKWISE. Check that the pulleys are still in alignment with the timing marks.
    5. If the No. 1 idler pulley uses a green tension spring, slowly turn the crankshaft pulley 1 7 / 8 revolutions, and align its groove with the mark at 45 degrees BTDC (for the No. 1 cylinder) of the No. 1 timing belt cover.
    6. Tighten the No. 1 idler pulley set bolt to 31 ft. lbs. (42 Nm).
    7. Be sure there is belt tension between the crankshaft and camshaft timing pulleys.
14. Place the right-hand engine mounting bracket in position but do not install the bolts.
15. Install the upper (No. 2) timing cover with a new gasket(s).
16. Remove the engine crankshaft pulley bolt and pulley.
17. Using SST 09249-63010, or equivalent, install the mounting bolts for the right-hand mounting bracket. Tighten the mounting bolts to 38 ft. lbs. (52 Nm).
18. Align the crankshaft pulley set key with the pulley key groove. Install the pulley. Tighten the pulley bolt to 80 ft. lbs. (108 Nm).
19. Install the spark plugs.
20. Install the right-hand mounting insulator, as follows:
    1. Attach the mounting insulator to the body and mounting bracket with the 4 bolts and 2 nuts.
    2. Tighten the 3 bolts to hold the mounting insulator to the body. Tighten the bolts to 47 ft. lbs. (64 Nm).
    3. Tighten the 2 nuts and bolt to hold the mounting insulator to the mounting bracket. Tighten the bolt to 27 ft. lbs. (37 Nm) and the nut to 38 ft. lbs. (52 Nm).
21. Install and adjust the power steering pump drive belt.
22. Install the right-hand engine undercover.
23. Install the right front wheel.
24. Lower the engine.
25. If equipped, install the ABS actuator.
26. Install the alternator and alternator bracket.
27. Install the wiring harness bracket for the DLC1.
28. Install the power steering reservoir bracket and reservoir.
29. Connect the negative battery cable.
30. Start the engine and check the timing.

step 13.4 is never to be skipped. ask why., most do. and it fails.

in the factory service manual FSM.

or

login to

alldata.com

and read all the steps



3VZ-FE (and 2vz)
this is your engine. and has many steps

key is timing and proper belt tension and is free running engine.



quote

Prior to timing belt removal, make sure all the match-marks are there-2VZ-FE and 3VZ-FE engines

less photos:

the crank mark is CR -line

the cam pulleys, 3v pulley to R-cam mark

and 3v pulley to L-cam mark. (photos are best).

1. Remove the timing belt.

If the timing belt is to be reused, draw a directional arrow on the timing belt in the direction of engine rotation (clockwise) and place matchmarks on the timing belt and crankshaft gear to match the drilled mark on the pulley.

1. With a 10mm hex wrench, remove the setbolt, plate washer and the No. 1 idler pulley.



2. Remove the crankshaft timing pulley, if it can NOT be removed by hand, use two flat bladed tools. Position shop rags on the components to prevent damage.

TO INSTALL:

1. Turn the crankshaft until the key groove in the crankshaft timing pulley is facing upward. Slide the timing pulley on so that the flange side faces inward.



2. Apply bolt adhesive to the first few threads of the No. 1 idler pulley setbolt, install the plate washer and pulley and then tighten the bolt to 25 ft. lbs. (34 Nm).



3. Install the timing belt on the crankshaft timing, No. 1 idler and water pump pulleys.

If the old timing belt is being reinstalled, make sure the directional arrow is facing in the original direction and that the belt and crankshaft gear matchmarks are properly aligned.

1. Install the lower (No. 1) timing cover and tighten the bolts.



2. Align the crankshaft pulley set key with the key groove on the pulley and slide the pulley on. Tighten the bolt to 181 ft. lbs. (245 Nm).



3. Install the No. 2 idler pulley and tighten the bolt to 29 ft. lbs. (39 Nm). Check that the pulley moves smoothly.



4. Slide the left pulley, facing the flange side outward. Align the knock pin hole of the camshaft with the knock pin of the timing pulley, then install the knock pin. Tighten the left camshaft timing pulley bolt to 80 ft. lbs. (108 Nm).



5. Set the No. 1 cylinder to TDC again. Turn the right camshaft until the knock pin hole is aligned with the timing mark on the No. 3 belt cover. Turn the left pulley until the marks on the pulley are aligned with the mark on the No. 3 timing cover.



6. Check that the mark on the belt matches with the edge of the lower cover. If not, shift it on the crank pulley until it does. Turn the left pulley clockwise a bit and align the mark on the timing belt with the timing mark on the pulley. Slide the belt over the left pulley. Now move the pulley until the marks on it align with the one on the No. 3 cover. There should be tension on the belt between the crankshaft pulley and the left camshaft pulley.



7. Align the installation mark on the timing belt with the mark on the right side camshaft pulley. Hang the belt over the pulley with the flange facing inward. Align the timing marks on the right pulley with the one on the No. 3 cover and slide the pulley onto the end of the camshaft. Move the pulley until the camshaft knock pin hole is aligned with the groove in the pulley and then install the knock pin. Tighten the bolt to 55 ft. lbs. (75 Nm).



8. Position a plate washer between the timing belt tensioner and the a block and then press in the pushrod until the holes are aligned between it and the housing. Slide a 1.27mm (3VZ-FE 1.5mm) Allen wrench through the hole to keep the push rod set. Install the dust boot and then install the tensioner. Tighten the bolts to 20 ft. lbs. (26 Nm). Don\'t forget to pull out the Allen wrench!



9. Turn the crankshaft clockwise two complete revolutions and check that all marks are still in alignment. If they aren\'t, remove the timing belt and start over again.



10. Install the right engine mount bracket and tighten it to 30 ft. lbs. (39 Nm).



11. Position a new gasket and then install the upper (No. 2) timing cover. refer to the illustration for bolt positioning.



12. Install the spark plugs.



13. On the 2VZ-FE, install the right engine mount insulator. Tighten the bolt to 47 ft. lbs. (64 Nm), the bracket nut to 38 ft. lbs. (52 Nm) and the body nut to 65 ft. lbs. (88 Nm). Install the No. 1 stay and tighten it to 38 ft. lbs. (52 Nm). Install the No. 2 stay and tighten the bolt to 48 ft. lbs. (66 Nm) and the nut to 38 ft. lbs. (52 Nm).



14. On the 3VZ-FE, install the control rod and tighten the bolts to 47 ft. lbs. (64 Nm). Install the right stay and tighten it to 23 ft. lbs. (31 Nm).



15. Install and adjust the drive belts.



16. Install the fender apron seal and the wheel.



17. On the 3VZ-FE, install the No. 2 stay and tighten the bolt to 55 ft. lbs. (75 Nm), the nut to 46 ft. lbs. (62 Nm). Install the No. 3 stay and tighten it to 54 ft. lbs. (73 Nm).



18. Install the coolant overflow tank and the washer tank.



19. Install the power steering reservoir tank and the cruise control actuator.



20. Connect the battery cable, start the car and check for any leaks.

end quote.

Manual is not clear either, but do you have "3V" marks on the gears? You have the 3VZ engine, so I would use those.



To install:

1. Turn the crankshaft until the key groove in the crankshaft timing pulley is facing upward. Slide the timing pulley on so that the flange side faces inward.
2. Apply bolt adhesive to the first few threads of the No. 1 idler pulley setbolt, install the plate washer and pulley and then tighten the bolt to 25 ft. lbs. (34 Nm).
3. Install the timing belt on the crankshaft timing, No. 1 idler and water pump pulleys.

If the old timing belt is being reinstalled, make sure the directional arrow is facing in the original direction and that the belt and crankshaft gear matchmarks are properly aligned.

1. Install the lower (No. 1) timing cover and tighten the bolts.
2. Align the crankshaft pulley set key with the key groove on the pulley and slide the pulley on. Tighten the bolt to 181 ft. lbs. (245 Nm).
3. Install the No. 2 idler pulley and tighten the bolt to 29 ft. lbs. (39 Nm). Check that the pulley moves smoothly.
4. Slide the left pulley, facing the flange side outward. Align the knock pin hole of the camshaft with the knockpin of the timing pulley, then install the knock pin. Tighten the left camshaft timing pulley bolt to 80 ft. lbs. (108 Nm).
5. Set the No. 1 cylinder to TDC again. Turn the right camshaft until the knock pin hole is aligned with the timing mark on the No. 3 belt cover. Turn the left pulley until the marks on the pulley are aligned with the mark on the No. 3 timing cover.
6. Check that the mark on the belt matches with the edge of the lower cover. If not, shift it on the crank pulley until it does. Turn the left pulley clockwise a bit and align the mark on the timing belt with the timing mark on the pulley. Slide the belt over the left pulley. Now move the pulley until the marks on it align with the one on the No. 3 cover. There should be tension on the belt between the crankshaft pulley and the left camshaft pulley.
7. Align the installation mark on the timing belt with the mark on the right side camshaft pulley. Hang the belt over the pulley with the flange facing inward. Align the timing marks on the right pulley with the one on the No. 3 cover and slide the pulley onto the end of the camshaft. Move the pulley until the camshaft knock pin hole is aligned with the groove in the pulley and then install the knock pin. Tighten the bolt to 55 ft. lbs. (75 Nm).
8. Position a plate washer between the timing belt tensioner and the a block and then press in the pushrod until the holes are aligned between it and the housing. Slide a 1.27mm (3VZ-FE 1.5mm) Allen wrench through the hole to keep the push rod set. Install the dust boot and then install the tensioner. Tighten the bolts to 20 ft. lbs. (26 Nm). Don't forget to pull out the Allen wrench!
9. Turn the crankshaft clockwise two complete revolutions and check that all marks are still in alignment. If they aren't, remove the timing belt and start over again.
10. Install the right engine mount bracket and tighten it to 30 ft. lbs. (39 Nm).
11. Position a new gasket and then install the upper (No. 2) timing cover. refer to the illustration for bolt positioning.
12. Install the spark plugs.
13. On the 2VZ-FE, install the right engine mount insulator. Tighten the bolt to 47 ft. lbs. (64 Nm), the bracket nut to 38 ft. lbs. (52 Nm) and the body nut to 65 ft. lbs. (88 Nm). Install the No. 1 stay and tighten it to 38 ft. lbs. (52 Nm). Install the No. 2 stay and tighten the bolt to 48 ft. lbs. (66 Nm) and the nut to 38 ft. lbs. (52 Nm).
14. On the 3VZ-FE, install the control rod and tighten the bolts to 47 ft. lbs. (64 Nm). Install the right stay and tighten it to 23 ft. lbs. (31 Nm).
15. Install and adjust the drive belts.
16. Install the fender apron seal and the wheel.
17. On the 3VZ-FE, install the No. 2 stay and tighten the bolt to 55 ft. lbs. (75 Nm), the nut to 46 ft. lbs. (62 Nm). Install the No. 3 stay and tighten it to 54 ft. lbs. (73 Nm).
18. Install the coolant overflow tank and the washer tank.
19. Install the power steering reservoir tank and the cruise control actuator.
20. Connect the battery cable, start the car and check for any leaks.

Here are instructions from autozone.com: Please be sure the belt is tight on the right side with the gears aligned before releasing tensioner onto belt.

To install:

1. If necessary, install the timing belt inside cover.
2. Slide the timing belt guide on the crankshaft so that the concave side faces the oil pump, then install the sprocket key in the groove in the crankshaft.
3. Slide the pulley onto the crankshaft, and install the center retaining bolt. Tighten the center bolt to 48-54 ft. lbs. (65-75 Nm) for 1986-88 1.3L engines, to 76-83 ft. lbs. (105-115 Nm) for 1989-95 1.3L engines, or to 58-65 ft. lbs. (80-90 Nm) for 1.6L engines. To hold the crankshaft from turning, you can use Suzuki Tool 09927-56010 (or equivalent), or a large prybar inserted in the transmission housing slot and the flywheel teeth.
4. Install the timing belt camshaft sprocket, ensuring that the slot in the sprocket engages the camshaft (pulley) pin; this ensures that the sprocket is properly positioned on the end of the camshaft. Secure the camshaft with the metal rod used during removal, then tighten the sprocket bolt to 41-46 ft. lbs. (56-64 Nm).
5. Assemble the timing belt tensioner plate and the tensioner, making sure that the lug of the tensioner plate engages the tensioner.

Fig. 14: Assemble the tensioner (2) and the plate (1) so that the lug (3) engages the hole (4) in the tensioner

1. Install the timing belt tensioner, tensioner plate and spring on the engine. Tighten the mounting bolt and stud only finger-tight at this time. Ensure that when the tensioner is moved in a counterclockwise direction, the tensioner moves in the same direction. If the tensioner does not move, remove it and the tensioner plate to reassemble them properly.
2. Loosen all rocker arm valve lash locknuts and adjusting screws. This will permit movement of the camshaft without any rocker arm associated drag, which is essential for proper timing belt tensioning. If the camshaft does not rotate freely (free of rocker arm drag), the belt will not be properly tensioned.
3. Rotate the camshaft sprocket clockwise until the timing mark on the sprocket and the V mark on the timing belt inside cover are aligned.
4. Using a 17mm wrench, or socket and breaker bar, on the crankshaft sprocket center bolt, turn the crankshaft clockwise until the punch mark on the sprocket is aligned with the arrow mark on the oil pump.

Fig. 15: When installing the crankshaft sprocket (pulley), ensure that the concave side of the timing belt guide is facing the engine Fig. 16: Before installing the timing belt, position the camshaft sprocket (1) so that the timing mark on the sprocket (2) is aligned with the notch (3) on the inside timing belt cover (4)

Fig. 17: ... and ensure that the crankshaft sprocket (1) timing mark (2) is aligned with the mark on the oil pump (3)

Fig. 18: Install the timing belt on the sprockets so that there is no slack in the drive side of the belt (1), then install the tensioning assembly

Fig. 19: To properly tension the timing belt, rotate the crankshaft through two full revolutions

1. With the camshaft and crankshaft marks properly aligned, push the tensioner up with your finger and install the timing belt on the two sprockets, ensuring that the drive side of the belt is free of all slack. Release your finger from the tensioner. Be sure to install the timing belt so that the directional arrow is pointing in the appropriate direction.

In this position, the No. 4 cylinder is at Top Dead Center (TDC) on the compression stroke.

1. Rotate the crankshaft clockwise two full revolutions, then tighten the tensioner stud to 18-21 ft. lbs. (24-30 Nm) for 1986-88 models, or to 80-106 inch lbs. (9-12 Nm) for 1989-95 models. Then, tighten the tensioner bolt to 18-21 ft. lbs. (24-30 Nm).
2. Ensure that all four timing marks are still aligned as before; if they are not, remove the timing belt, and install and tension it again.
3. Install the timing belt cover and all related components.

Hi,


You find the timing marks on the picture below.





Removal
Remove auxiliary 1. drive belts.
2. Support engine.
Remove:
Engine mounting and bracket.
Timing belt upper cover [1].
3.
4. Turn crankshaft clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Remove:
Crankshaft pulley bolt [4].
Crankshaft pulley [5]. Use tool No.09213-60017.
5.
6. Ensure timing marks aligned [2] & [3].
7. Slacken tensioner bolt [6]. Move tensioner away from belt and lightly tighten bolt.
Remove:
Timing belt lower cover [7].
Crankshaft sprocket guide washer [9].
Timing belt.
Tensioner pulley.

Installation
Installation
1. Check tensioner pulley for smooth operation.
2. Check free length of tensioner spring is 46,0 mm [8]. Replace spring if necessary.
3. Fit tensioner and spring. Ensure spring is connected correctly.
4. tighten bolt [6].
5. Ensure timing marks aligned [2] & [3].
6. Fit timing belt. Ensure belt is taut between sprockets.
Install:
Crankshaft sprocket guide washer [9].
Timing belt lower cover [7].
Crankshaft pulley [5].
7.
8. Slacken tensioner bolt 1/2 turn [6].
9. Turn crankshaft two turns clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Turn crankshaft slowly 1 7/8 turns clockwise until crankshaft pulley timing mark [3] aligned with 45° BTDC mark [10] on
timing belt lower cover [7].
10.
11. Tighten tensioner bolt [6]. Tightening torque: 42 Nm.
12. Install components in reverse order of removal.
13. Tighten crankshaft pulley bolt [4]. Tightening torque: 108 Nm.
Manufacturer: Toyota

Timing chain is only available in the 3.3L and 3.8L engines.

Yours has a belt. (if you're SURE its a 3.0L)

Here is the info on changing it...

3.0L Engine
The timing belt can be inspected by removing the upper front outer timing belt cover.
Working on any engine (especially overhead camshaft engines) requires much care be given to valve timing. It is good practice to set the engine up at TDC No. 1 cylinder firing position before beginning work. Verify that all timing marks on the crankshaft and camshaft sprockets are properly aligned before removing the timing belt and starting camshaft service. This serves as a point of reference for all work that follows. Valve timing is very important and engine damage will result if the work is incorrect.

1. Disconnect the negative battery cable.
2. Remove the accessory drive belts. Remove the engine mount insulator from the engine support bracket.
3. Remove the engine support bracket. Remove the crankshaft pulleys and torsional damper. Remove the timing belt covers.
4. Rotate the crankshaft until the sprocket timing marks are aligned. The crankshaft sprocket timing mark should align with the oil pump timing mark. The rear camshaft sprocket timing mark should align with the generator bracket timing mark and the front camshaft sprocket timing mark should align with the inner timing belt cover timing mark.
5. If the belt is to be reused, mark the direction of rotation on the belt for installation reference.
6. Loosen the timing belt tensioner bolt and remove the timing belt.
7. If necessary, remove the timing belt tensioner.
8. Remove the crankshaft sprocket flange shield and crankshaft sprocket.
9. Hold the camshaft sprocket using spanner tool MB990775, or equivalent, and remove the camshaft sprocket bolt and washer. Remove the camshaft sprocket.
10. To install:
    
11. Install the camshaft sprocket on the camshaft with the retaining bolt and washer. Hold the camshaft sprocket using spanner tool MB990775, or equivalent, and tighten the bolt to 70 ft. lbs. (95 Nm).
12. Install the crankshaft sprocket.
13. If removed, install the timing belt tensioner and tensioner spring. Hook the spring upper end to the water pump pin and the lower end to the tensioner bracket with the hook out.
14. Turn the timing belt tensioner counterclockwise full travel in the adjustment slot and tighten the bolt to temporarily hold it in this position.
15. Rotate the crankshaft sprocket until its timing mark is aligned with the oil pump timing mark.
16. Rotate the rear camshaft sprocket until its timing mark is aligned with the timing mark on the generator bracket.
17. Rotate the front (radiator side) camshaft sprocket until its mark is aligned with the timing mark on the inner timing belt cover.
18. Install the timing belt on the crankshaft sprocket while keeping the belt tight on the tension side.
19. Position the timing belt over the front camshaft sprocket (radiator side). Next, position the belt under the water pump pulley, then over the rear camshaft sprocket and finally over the tensioner.
20. Apply rotating force in the opposite direction to the front camshaft sprocket (radiator side) to create tension on the timing belt tension side. Check that all timing marks are aligned.
21. Install the crankshaft sprocket flange.
22. Loosen the tensioner bolt and allow the tensioner spring to tension the belt.
23. Rotate the crankshaft 2 full turns in a clockwise direction. Turn the crankshaft smoothly and in a clockwise direction only.
24. Align the timing marks. If all marks are aligned, tighten the tensioner bolt to 250 inch lbs. (28 Nm). Otherwise repeat the installation procedure.
25. Install the timing belt covers. Install the engine support bracket. Tighten the support bracket mounting bolts to 35 ft. lbs. (47 Nm).
26. Install the engine mount insulator, torsional damper and crankshaft pulleys. Tighten the crankshaft pulley bolt to 112 ft. lbs. (151 Nm).
27. Install the accessory drive belts and adjust them to the proper tension.
28. Reconnect the negative battery cable.
29. Run the engine and check for proper operation. Road test the vehicle.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Timing Belt
Removal
1. Disconnect battery ground cable.
2. Remove air cleaner assembly.
3. Remove radiator upper fan shroud from radiator.
4. Move drive belt tensioner to loose side using wrench
then remove drive belt.
850RW001
Legend
(1) Crankshaft Pulley
(2) Cooling Fan Pulley
(3) Tensioner
(4) Generator
(5) Air Conditioner Compressor
(6) Power Steering Oil Pump
(7) Drive Belt
5. Remove cooling fan assembly four nuts, then the
cooling fan assembly.
6. Remove cooling fan drive pulley assembly.
7. Remove idle pulley assembly.
8. Remove serpentine belt tensioner assembly.
9. Remove power steering pump assembly.
10.Remove crankshaft pulley assembly using
5–8840–0133–0 crankshaft holder, hold crankshaft
pulley remove center bolt, then the pulley.
11. Remove right side timing belt cover then left side
timing belt cover.
12. Remove lower timing belt cover
13. Remove pusher.
CAUTION: The pusher prevents air from entering
the oil chamber. Its rod must always be facing
upward.
014RW011
Legend
(1) Up Side
(2) Down Side
(3) Direction For Installation
(4) Locking Pin
14. Remove timing belt.
CAUTION:
1. Do not bend or twist the belt, otherwise its core
could be damaged. The belt should not be bent at
a radius less than 30 mm.
2. Do not allow oil or other chemical substances to
come in contact with the belt. They will shorten
the life.
3. Do not attempt to pry or stretch the belt with a
screw driver or any other tool during installation.
4. Store timing belt in a cool and dark place. Never
expose the belt direct sunlight or heat.
6A–30 ENGINE MECHANICAL
Installation
NOTE: For correct belt installation, the letter on the belt
must be able to be read as viewed from the front of the
vehicle.
014RY00042
Legend
(1) Crankshaft Timing Pulley
(2) RH Bank Camshaft Drive Gear Pulley
(3) Water Pump Pulley
(4) Idle Pulley
(5) LH Bank Camshaft Drive Gear Pulley
(6) Tension Pulley
014RY00043
Legend
(7) Alignment Mark on Oil Pump.
(8) Alignment Mark on Timing Belt
(9) Alignment Mark (notch) on Crankshaft Timing
Pulley.
(10) Alignment Mark (groove) on Crankshaft Timing
Pulley.
014RW006
Legend
(1) Timing Belt
(2) Engine Rotation Direction
(3) Cylinder Head Side
1. Install timing belt.
1. Align the mark (notch) of crankshaft timing pulley
(2) with mark on oil pump (1).
Align the mark (groove) on the crankshaft timing
pulley (3) with alignment mark (white dots line) on
the timing belt (4).
NOTE: When timing marks are aligned, No.2 piston will
be on Top Dead Center.
014RW003
Legend
(1) Alignment Mark on Oil Pump
(2) Groove on Crankshaft Timing Pulley
(3) Alignment Mark on Crankshaft Timing Pulley
(4) Alignment Mark on Timing Belt
ENGINE MECHANICAL 6A–31
2. Align the alignment mark on the RH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover RH (3).
3. Align the alignment mark (white line) on the timing
belt (1) with alignment mark on the RH bank
camshaft drive gear pulley (2) (on the left side as
viewed from the front of the vehicle) and put the
timing belt on the camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
014RW00004
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover RH.
4. Align the alignment mark on the LH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover LH (3).
5. Align the alignment mark (white line) on the timing
belt (1) with the alignment mark on the LH bank
camshaft drive gear pulley (2).
When aligning the timing marks, use a wrench to
turn the camshaft drive gear pulley, then set the
timing mark between timing belt and camshaft
drive gear pulley and put the timing belt on the
camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
NOTE: It is recommended for easy installation that the
belt be secured with a double clip or equivalent clip after
it is installed the timing belt to each pulley.
014RW00005
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover LH.
6. Install crankshaft pulley temporarily and tighten
center bolt by hand (do not use a wrench).
Turn the crankshaft pulley clockwise to give some
belt slack between the crankshaft timing pulley
and the RH bank camshaft drive gear pulley.
2. Install pusher and tighten bolt to the specified torque.
Torque : 25 N·m (2.5 Kg·m/18 lb ft)
1. Install the pusher while pushing the tension pulley
to the belt.
2. Pull out pin from the pusher.
NOTE: When reusing the pusher, press the pusher with
approximately 100Kg to retract the rod, and insert a pin
(1.4 mm piano wire).
014RW011