1995 Pontiac Grand Am Logo

Related Topics:

Anonymous Posted on Apr 22, 2017

Where do all the cables go from wiring harness to starter motor solenoid?

On a 1995 Pontiac Grand Am SE 2.3L quad 4: Trying to figure out where all the cables go that are toward the front of the car go. I need to know where the short multi-cable with 2 black and 1 blue wire goes? And also the longer multi-wired cable with 6 red cables. There is also a long one attached to a fuse/link? with a larger opening on the connector. I'm replacing a starter motor, and I don't think they all fit on the single solenoid terminal. I know the positive battery cable goes on this one terminal. I would really appreciate your help with this. Thanks, Deanoman in Washington

3 Related Answers

Anonymous

  • 99 Answers
  • Posted on Sep 29, 2008

SOURCE: starter

check ALL connections relating to the starter and please email me at [email protected] with any other info or questions

Ad

Anonymous

  • 6982 Answers
  • Posted on May 24, 2009

SOURCE: STARTER MOTOR WIRING

The wires with the large loops go on the big terminal. The purple wire likely is the one with the smaller loop that goes on the right terminal (facing the solenoid). That is ith trigger wire from the ignition key.Do not permit the wires from either terminals to touch.

emissionwiz

Marvin

  • 85242 Answers
  • Posted on May 30, 2009

SOURCE: I want to install a stereo in a 2001 grand am se but the wires were cut.

Here are the wires colors of the harness and what they do.

2001 Pontiac Grand Am Car Audio Wiring Diagram
Car Radio Battery Constant 12v+ Wire: Orange
Car Radio Accessory Switched 12v+ Wire: The radio harness does not provide a switched power source. Run a wire to the fusebox for switched power.
Car Radio Ground Wire: Black/White
Car Radio Illumination Wire: Gray
Car Stereo Dimmer Wire: Brown
Car Stereo Antenna Trigger Wire: N/A
Car Stereo Amp Trigger Wire: Pink
Car Stereo Amplifier Location: Mounted behind trim in the left side of the trunk.
Car Audio Front Speakers Size: N/A
Car Audio Front Speakers Location: N/A
Left Front Speaker Positive Wire (+): Tan
Left Front Speaker Negative Wire (-): Gray
Right Front Speaker Positive Wire (+): Light Green
Right Front Speaker Negative Wire (-): Dark Green
Car Audio Rear Speakers Size: N/A
Car Audio Rear Speakers Location: N/A
Left Rear Speaker Positive Wire (+): Brown
Left Rear Speaker Negative Wire (-): Yellow
Right Rear Speaker Positive Wire (+): Dark Blue
Right Rear Speaker Negative Wire (-): Light Blue

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Where is the starter located on a 2008 pontiac g 6 4 cylinder

Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle. Remove the "S" terminal connector from the starter solenoid. Remove the engine harness lead (2) from the starter
Remove the positive battery cable nut (2) from the starter solenoid. Remove the positive battery cable (3) and engine harness terminal (4) from the starter solenoid.
Remove the starter motor bolts. Remove the starter motor.
Has four engines possible in your G6 ,starter removal is simalier for all except one the catalytic converter has to come off.
0helpful
1answer

I have got the starter diconnected from my 2005 5.7 jeep gc but I cant get it out to replace it

1. Disconnect and isolate negative battery cable.
2. Raise and support vehicle.
3. Note: If equipped with 4WD and certain transmissions, a support bracket is used between front axle and side of transmission. Remove 2 support bracket bolts at transmission. Pry support bracket slightly to gain access to lower starter mounting bolt.
4. Remove two mounting bolts (2).
5. Move starter motor towards front of vehicle far enough for nose of starter pinion housing to clear housing. Always support starter motor (1) during this process, do not let starter motor hang from wire harness.
6. Tilt nose downwards and lower starter motor far enough to access and remove nut that secures battery positive cable wire harness connector eyelet to solenoid battery terminal stud. Do not let starter motor hang from wire harness.
7. Remove battery positive cable wire harness connector eyelet from solenoid battery terminal stud.
8. Disconnect battery positive cable wire harness connector from solenoid terminal connector receptacle.
9. Remove starter motor.
3helpful
3answers

How to Replace the Starter in a 1999 Pontiac Grand

starter is located on the engine block down below.

Removal & Installation To Remove:
Before servicing the vehicle, refer to the precautions in the beginning of this section.
  1. Remove or disconnect the following:
    • Negative battery cable
    • Radiator lower air deflector
    • Torque converter cover
    • Electrical connections from the starter
    • Starter motor
To Install:
  1. Install or connect the following:
    • Starter motor and torque the bolts to 32 ft. lbs. (43 Nm)
    • Starter solenoid BAT terminal
    • Starter solenoid S terminal
    • Torque converter cover and torque the bolts to 89 inch lbs. (10 Nm)
    • Radiator lower air deflector and torque the bolts to 15 ft. lbs. (20 Nm)
    • Negative battery cable
Starter removal/installation – 3.1L & 3.4L engines 9306zg15.gif

Starter removal/installation -3.8L engine 9306zg17.gif
1helpful
1answer

The wires on a starter on a 1994 grand prix se 3.1l

The wire to the starter that has the small eyelet connector attaches to the "S" terminal on the starter solenoid, all other wire or wires, with the larger eyelet connector should be connected along with the Pos. (+) battery cable on the main "BAT" terminal of the starter solenoid.
0helpful
1answer

How to remove a starter in a 1995 pontiac grand am quad-four

disconnect battery,,jack up the car,,support car before u craw under it,,take off wire cover on starter wire,some times it their or not,,take battery wire of & smaller wire off,take the starter bolts out,,take starter out,,reverse when installing new starter
0helpful
1answer

Need to replace motor and transmission in a 97 Pontiac Grand AM G

Changing from a 1992 to a 1997 < WILL NOT Be EASY , As you must HAVE the ENTIRE ENGINE WIRING HARNESS , And ALSO the ECM for the older Set up. In the "5" YEARS there Were MANY CHANGES to the ENGINE Components= SENSORS and ACTUATERS .
its just a BETTER IDEA to Stay Whitin a year or 2 when Swaping ENGINES. SIZE OF SENSORS ETC. MAKES IT DIFICULT
3helpful
2answers

Vehicle "clicks" when trying to start...

Clicking is the solenoid, on top of your starter, have someone crank while you tap on it, lots of times this will make it connect and engage. if it works then replace solenoid on starter.
Not finding what you are looking for?

253 views

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...