Evap canister where is it located?

In the 2008 Kia Sportage, the purge evacuation (EVAP) solenoid is typically located near the charcoal canister. The exact location may vary slightly depending on the specific engine configuration and optional equipment, but here is a general guideline:

1. Locate the Charcoal Canister: The charcoal canister is a component of the EVAP system and is responsible for storing fuel vapors. It is usually located in the rear of the vehicle, near the fuel tank or in the engine compartment. The canister is a cylindrical or rectangular-shaped container.
2. Find the EVAP Solenoid: Once you have located the charcoal canister, look for a smaller component connected to it. This component is the purge evacuation (EVAP) solenoid. It is typically a small plastic or metal device with electrical connectors and vacuum hoses.
3. Follow the Hoses and Wires: Trace the vacuum hoses and electrical wires connected to the charcoal canister to locate the EVAP solenoid. The solenoid may be connected directly to the canister or positioned nearby.

Please note that the exact location of the EVAP solenoid may vary slightly depending on the specific engine and emission system layout of your 2008 Kia Sportage. Consulting the vehicle's service manual or contacting a Kia dealership may provide more accurate and detailed information tailored to your specific model.
It's important to exercise caution when working with the EVAP system and its components, as they are part of the vehicle's emission control system. If you are unsure or uncomfortable performing the task yourself, it's recommended to seek assistance from a qualified technician or a reputable automotive service center. They have the expertise and tools to locate and service the EVAP solenoid properly.

Evaporative Emission Canister Purge Solenoid Valve Replacement
Removal Procedure
Remove the air cleaner assembly from the studs and reposition to the side.
Disconnect the evaporative emission (EVAP) canister purge valve electrical connector (1).
Disconnect the EVAP canister purge valve tube from the intake manifold. Refer to Plastic Collar Quick Connect Fitting Service.
Disconnect the chassis EVAP vapor line from the EVAP canister purge valve. Refer to Plastic Collar Quick Connect Fitting Service.
Remove the EVAP canister purge valve bracket bolt.
Remove the EVAP canister purge valve with bracket.
Remove the EVAP canister purge valve from the bracket.
Inspect for carbon release in the EVAP canister purge valve ports. If there is any loose carbon, replace the EVAP canister and any components necessary to remove the carbon particles.
Installation Procedure
Install the EVAP canister purge valve to the bracket.
Position the EVAP canister purge valve with bracket to the cylinder head.
Caution: Refer to Fastener Caution.
Install the EVAP canister purge valve bracket bolt.
Tighten:
Tighten the bolt to 18 [n-m] (13 lb ft).
Connect the EVAP canister purge valve tube to the intake manifold. Refer to Plastic Collar Quick Connect Fitting Service.
Connect the chassis EVAP vapor line to the EVAP canister purge valve. Refer to Plastic Collar Quick Connect Fitting Service.
Connect the EVAP canister purge valve electrical connector (1).
Position the air cleaner assembly and install onto the studs.

The Evaporative Emission (EVAP) Canister Purge Solenoid Valve is located in the EVAP canister, above the rear of the muffler. The Evaporative Emission (EVAP)Canister Purge Solenoid Valve is located in the EVAP canister, above the rear of the muffler.

It's located under the vehicle back behind the fuel tank , Installed in the canister ! Remove the EVAP canister vent solenoid valve from the canister !
Rotate the EVAP canister vent solenoid valve counterclockwise in order to release it from the locked position.
Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle . Disconnect the evaporative emission (EVAP) canister harness electrical connector (2) from the EVAP vent solenoid valve. Clean away any debris that may be present around the EVAP canister vent solenoid valve.
Remove the EVAP canister bolt. Lower the EVAP canister.

The canister is located in a frame behind the left rear wheel, and you will need wrenches, a socket set, and a jack to raise the back of the truck. Carefully remove the hoses from the canister - if you damage the quick connects, you will have a big problem. Then remove the canister frame by removing the bolts holding it (remove the screws holding the left rear plastic wheel well to get access to the front of the canister frame). Remove the old canister from the frame, attach the new canister, and then reinstall the frame.
If you are having a problem with the EVAP system, you should also check the hoses and replace the EVAP purge valve and the EVAP solenoid valve ( typical failure points on these vehicles - if you have a problem with one component, the rest will follow shortly after). The purge valve is located on the bottom of the vehicle near the center of the rear axle (just follow the small purge hose attached to the canister). The vent valve is located on the top right side on the engine. All parts are available from Amazon or a GM dealer.

Error Code: P0440
Fault Location:
Evaporative Emission (EVAP) System - Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Soution:
Check Evaporative Emission (EVAP) System Sealing.
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .

Error Code: P0441
Fault Location:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Solutions:
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Perform Output Test.
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .
Check Evaporative Emission (EVAP) Canister.
Perform Basic Setting.
Check Pipes between Tank Breathing and Throttle Body.

Error Code: P0446
Fault Location:
Evaporative Emission (EVAP) System, Vent Control - Circuit Malfunction
Possible Cause:
Wiring harness.
Evaporative emission (EVAP) canister purge valve.
Engine control module (ECM).

For the location of canister purge valve,check the following help links mentioned below:--
Click the link :---

Location for EVAP Purge Valve Solenoid?

http://schematicsdiagram.blogspot.in/2012/06/2002-nissandatsun-pathfinder-location.html

------------------

How to disconnect the hose form the Evap Canister?

http://schematicsdiagram.blogspot.com/2011/12/how-to-disconnect-hose-form-evap.html

-------------

2004 Chrysler PT Cruiser: Location of EVAP Purge Solenoid Valve?

http://schematicsdiagram.blogspot.in/2012/06/2004chrysler-pt-cruiser-location-of.html

-----------
These will help.
Thanks.

Which code specifically? Do not assume you need a new solenoid. Our recommendation will depend on the specific code and some troubleshooting results. I usually recommend checking over all the EVAP vacuum lines and the gas cap too whenever there is a purge valve code. Check the vacuum lines at the cannister in the left rear bumper. I will paste info on the purge solenoid below.

P0440 Evaporative emission (EVAP) system - malfunction

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve

P0441 Evaporative emission (EVAP) system - incorrect flow detected

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve

P0442 Evaporative emission (EVAP) system - small leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve

P0443 Evaporative emission (EVAP) canister purge valve - circuit malfunction

Possible causes: Wiring, EVAP canister purge valve, ECM

P0444 Evaporative emission (EVAP) canister purge valve -open circuit

Possible causes: Wiring open circuit, EVAP canister purge valve, ECM

P0445 Evaporative emission (EVAP) canister purge valve -short circuit

Possible causes: Wiring short circuit, EVAP canister purge valve, ECM

P0450 Evaporative emission (EVAP) pressure sensor - circuit malfunction

Possible causes: Wiring, EVAP pressure sensor, ECM

P0455 Evaporative emission (EVAP) system - large leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve

P0456 Evaporative emission system - very small leak detected

Possible causes: Mechanical fault, hose connection(s), EVAP pressure "sensor

P0457 Evaporative emission system - leak detected (fuel cap loose/off)

Possible causes: Mechanical fault, hose connection(s), EVAP pressure sensor

P0458 Evaporative emission system, purge control valve -circuit low

Possible causes: Wiring short to earth, EVAP valve

P0459 Evaporative emission system, purge control valve -circuit high
Possible causes: Wiring short to positive, EVAP valve

Evaporative Emission Purge Solenoid

Description & Operation
The duty cycle EVAP canister purge solenoid (DCP) regulates the rate of vapor flow from the EVAP canister to the intake manifold. The Powertrain Control Module (PCM) operates the solenoid.
During the cold start warm-up period and the hot start time delay, the PCM does not energize the solenoid. When de-energized, no vapors are purged. The PCM de-energizes the solenoid during open loop operation.
The engine enters closed loop operation after it reaches a specified temperature and the time delay ends. During closed loop operation, the PCM cycles (energizes and de-energizes) the solenoid 5 or 10 times per second, depending upon operating conditions. The PCM varies the vapor flow rate by changing solenoid pulse width. Pulse width is the amount of time that the solenoid is energized. The PCM adjusts solenoid pulse width based on engine operating condition.
Removal & Installation
The duty cycle evaporative (EVAP) canister purge solenoid is located in the engine compartment near the brake master cylinder.

1. Disconnect electrical connector at solenoid.
2. Disconnect vacuum lines at solenoid.
3. Lift solenoid slot from mounting bracket for Removal & Installation.

To Install:

1. Position solenoid slot to mounting bracket.
2. Connect vacuum lines to solenoid. Be sure vacuum lines are firmly connected and not leaking or damaged. If leaking, a Diagnostic Trouble Code (DTC) may be set with certain emission packages.
3. Connect electrical connector to solenoid.
   

Purge solenoid location:


EVAP cannister location:

Some might have an ses p0446, evap emissions vent circuit low. If you take it to the dealer they want 300-400.00 to fix the problem. GM has a service bulletin on this condition and have the updated part for 180.00, thats suppose to eliminate this issue.

Basically the problem is, the evap purge vent valve gets clogged with dirt, especially if the truck is used in dirty conditions. Well I figured there had to be a cheaper way to cure this problem.

Here it is:
1) find the location of the vent valve; its under the truck, locate the charcoal canister on the front of the gas tank and trace the vent line to the vent valve.
2) Take the bracket loose with a 5/8 wrench.
3) Spin the valve around so the side with the hole is facing you.
4) Take an air compressor and blow the vent valve out.
5) reinstall and clear the code and it's fixed.

Now I know the updated part from gm is supposed to keep the valve from clogging ever again, but why spend the money when all you have to do is blow out the vent valve every 50k-100kmi and save your $$$!

Subject: DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Service Engine Soon (SES) Lamp Illuminated (Replace Hose/Evaporative Emission (EVAP) Canister Vent Asm) #02-06-04-037A - (02/02/2005)
Models:
- 1999-2003 Chevrolet Silverado Models
- 1999-2003 GMC Sierra Models
--------------------------------------------------------------------------------
This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 02-06-04-037 (Section 06 -- Engine/Propulsion System).
--------------------------------------------------------------------------------
Condition
Some customers whose vehicles are operated in dusty type environments, such as farming or mining off-road type applications, may comment about the illumination of the instrument panel SES light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set.

Cause
Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition.

Part Number 15086429 Hose Asm-Evap Emis Cnstr Vent


Removal & Installation
Purge Solenoid Valve-2.2L (L61) Engine

1. Disconnect the evaporative emission (EVAP) canister purge valve harness connector.
2. Disconnect the vacuum pipe from the EVAP canister purge valve.
3. Disconnect the purge pipe from the EVAP canister purge valve.
4. Remove the EVAP canister purge valve and bracket.
5. Remove the EVAP canister purge valve from the purge bracket.
6. Inspect for carbon release in the EVAP canister purge valve ports.
   

To install:

1. Install the EVAP canister purge valve on to the purge bracket.
2. Install the EVAP canister purge valve and bracket. Tighten the purge bracket nut to 71 inch lbs. (8 Nm).
3. Connect the purge pipe to the EVAP canister purge valve.
4. Connect the vacuum pipe to the EVAP canister purge valve.
5. Connect the EVAP canister purge valve harness connector.
6. Remove the air cleaner outlet resonator.
7. Disconnect the EVAP canister purge valve harness connector.
8. Disconnect the engine purge pipe from the EVAP canister purge valve.
9. Disconnect the engine vacuum pipe from the EVAP canister purge valve.
10. Remove the EVAP canister purge valve mounting bracket attaching bolt.
11. Remove the EVAP canister purge valve along with the mounting bracket.
12. Installation is the reverse of the removal procedure. Tighten the bracket bolts to 71 inch lbs. (8 Nm).

Purge Solenoid Valve-2.4L Engines

1. Remove the front purge pipe from the evaporative emission (EVAP) canister purge valve.
2. Remove the rear purge pipe from the EVAP canister purge valve.
   NOTE The EVAP canister may have released carbon particles, which caused this part to fail, and may cause damage to other components. Check the EVAP canister for loose carbon before returning the vehicle to service.
   
3. Disconnect the EVAP canister purge valve electrical connector.
4. Insert a screwdriver between the EVAP canister purge valve and the mounting bracket in order to release the lock tab.
5. Remove the EVAP canister purge valve mounting bracket attaching nut, if replacing the bracket.
6. Remove the bracket.
   

To install:

1. Install the mounting bracket and the attaching nut for the EVAP canister purge valve. Tighten the nut to 71 inch lbs. (8 Nm).
2. Slide the EVAP canister purge valve onto the mounting bracket. Make sure the lock tab locks the valve in place.
3. Connect the EVAP canister purge valve electrical connector.
4. Connect the rear purge pipe to the EVAP canister purge valve.
5. Connect the front purge pipe to the EVAP canister purge valve.

Vent Solenoid Valve-2.2L & 2.4L Engines

1. Raise the vehicle
2. Loosen the EVAP canister vent valve hose clamp and slide the clamp down the hose away from the EVAP vent valve hose connection.
3. Remove the hose from the EVAP canister vent valve.
4. Remove the EVAP canister vent valve by placing a pry bar between the valve and mounting surface, and moving the valve forward.
5. Remove the clip from the EVAP canister vent valve harness connector
6. Disconnect the EVAP canister vent valve harness connector.
   

To install:

1. Connect the EVAP canister vent valve harness connector
2. Install the clip into the EVAP canister vent valve harness connector.
3. Install the EVAP canister vent valve by pushing the mounts into the original holes.
4. Lubricate the hose end with lubricant.
5. Install the hose to the EVAP canister vent valve.
6. Slide the EVAP canister vent valve hose clamp down on to the hose connection at the EVAP canister vent valve.
7. Lower the vehicle.

Hope this help (remember commetn and rated this).

The EVAP service port is located in the EVAP purge pipe between the EVAP purge solenoid and the EVAP canister. The service port is identified by a green colored cap.



Fig. Showing location of (1) Evaporative Emissions (EVAP) Canister Purge Solenoid and (2) Exhaust Gas Recirculation (EGR) Valve




Fig. EVAP Purge valve solenoid (3) mounting bolt (2) and insulator (1) on 2000-2005 4.8L, 5.3L, 6.0L Engines

Hope this help (remember rated the post).