2004 Honda Accord Logo
Anonymous Posted on Jul 30, 2013

P1676 error on a ford excape - what is the cause of this error code

1 Answer

_-__-___-_

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • Honda Master 20,706 Answers
  • Posted on Jan 30, 2014
_-__-___-_
Honda Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: Apr 06, 2013
Answers
20706
Questions
2
Helped
6803104
Points
57965

Is this Autozoned code? or a real scan tool. for modern cars.

did they show you, tell you or did you write it down wrong?



do post what tool produced this code, its rare.



a Honda Ford? really??? is this an engine swap?

if not a honda. you might want to post to Ford, as we dont have books on fords here.

but like all DTCs there are many causes, and the tech does the test

stated in the FSM. got FSM? factory service manual... youd need that.



no engine stated, or any year, Ford, so not possible to answer lacking that..

P1 xxx means factory ford only code. do not read other makers of cars codes, just ford. or fail big time..



i looked from 05 to 2011 codes for ford escape and get zero

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer
0helpful
1answer
1helpful
1answer

I have a ford excape 2008 and it is overheating. i have connected the fan staright and it does not overheat, what could be wrong

You have several problems I looked up the codes in the database
U0414 means invalid data received from four wheel drive clutch control module
P0118 engine coolant temp circuit high input
P260f evaporative system monitoring processor performance
I believe the overheating is caused by a bad relay. The p0118 code is not for the sensor it is for the circuit. Check the relays for the fans in the fuse box in engine compartment
0helpful
1answer

Please help my ssangyong rexton2.7 D gazoil Stuart only with Stuart pilot .because code error P11 48 C1623 P1676. P0343 Think you

C1623 is with in the chassis sensors P1148, P1623, P1676 is in the ECM not on my list of codes not sure what it is. call parts house and they can tell you what it is. PO343 is camshaft position sensor circuit high input. P1148 not sure not on my list of codes they may be in the newer codes list but I don't have an updated list
0helpful
1answer

2000 ford expedition I changed plugs pcv egr valve cover gasket I am still getting power loss and hesitation in drive and sometimes it stalls plus I have a b1676 code

power loss or stall problem and you also have B1676 code which your break lump or ABS Lamp indicators is on thats why when you press accelerator you dont get power sometimes has but mostly not meaning to say your car dont event go far ^_^ try to reset the code if not check the b1676 code which is regarding sensors= problem solve
1helpful
1answer

1999 honda oddesy van with trouble code p1676

not sure what it means but here is what the code says
P1676
FPTDR Signal Line Failure
0helpful
2answers

P1676 audi

VAG OBD Error Code Details for P1676 Drive by Wire-MIL Circ. Electrical Malfunction
0helpful
1answer

2005 ford excape with fuel rail pressure sensor, getting error code. Is there a diagram that shows where it is located if i want to replace it my self.

It is a fuel rail pressure switch

So you look on the fuel rail

If you dont know how to do that or test it,
you don't get involved

Just because you got a code, doesn't mean that is a problem

I called a Lincoln Dealer earlier this year & they only sold
4 in four years total, for all vehicles they service & outside parts sells

So that is not a common failure at all
2helpful
2answers

Check engine light code p1676 Chevy lumina Ltz

Trouble Code: P1676 (3.8L V6 VIN K Auto)
Evaporative Emission (EVAP) Purge Solenoid

Number of Trips to Set Code: 1
OBD II Monitor Type: CCM Details
Indicators: MIL Details
Trouble Code Conditions:
Conditions for Setting the DTC.
  • The ignition is on.
  • An improper voltage level has been detected on the output circuit which controls the EVAP purge solenoid.
  • The above conditions are present for at least 30 seconds.

Possible Causes:
  • Poor connection at the PCM. Inspect harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and poor terminal to wire connection.
  • Damaged harness.
  • Inspect the wiring harness for damage. If the harness appears to be OK, disconnect the PCM, turn the ignition on and observe a voltmeter connected between the EVAP purge solenoid control circuit and ground at the PCM harness connector while moving connectors and wiring harnesses related to the EVAP purge solenoid. A change in voltage will indicate the location of the malfunction.

1998 Chevrolet Lumina - Powertrain - Engine Controls - 3.8L - DTC P1676 Evaporative Emission (EVAP) Purge Solenoid Control Circuit
Not finding what you are looking for?

436 views

Ask a Question

Usually answered in minutes!

Top Honda Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

john h

Level 3 Expert

29494 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...