Replacing door speakers

Question edited for clarity and typo.
Question moved to sub category.

It is all in here.

2000 Mercury Sable Car Stereo Wire Colors and Locations

https://www.the12volt.com > installbay > stereodetail
2000 Mercury Sable Stereo Wiring ; Ground, Black/Light Green ; Illumination, Light Blue/Red ; Dimmer, n/a ; Antenna, Left Rear ; Front Speakers, 5" x 7" Doors.


..

The regulator runs a track.. a strip of alluminum up and down,which the window(galss) itself rides on...There is either bolts or rivits in the metal ststrip....remove them and clean all the glass out of track and install new glass in track bolt it in and re-install the plastics and door skin or anything else you might have removed....BE CAREFULL THOUGH AS PUTTING YOUR HAND IN AND OUT OF THE CUTOUTS OF DOOR CAN LEAVE YOU WITH QUITE A FEW CUS AND SCRAPES......

Section 01-09: Mirrors, Rear View 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Mirror, Power-Outside Rear View Removal

1. Disconnect battery ground cable (14301).
   

1. Remove front door trim panel (23942). Refer to Section 01-05.
   

1. Remove radio speaker grille from cover assembly by squeezing or pinching between thumb and index finger.
   

1. Remove two screws from cover assembly.
   

1. Disconnect outside rearview mirror wiring connector (C515-LH; C615-RH). Remove wiring guides as necessary.
   

1. Remove three outside rear view mirror retaining nuts. Remove outside rear view mirror (17682) while guiding wiring and connector through hole in door.
   

Item Part Number Description 1 17682 Outside Rear View Mirror 2 N621906-S36 Nut (3 Req'd) 3 F8DB-17D699-
AAW Cover Assembly Rear Substrate-LH 3 F8DB-17D698-
AAW Cover Assembly Rear Substrate-RH 4 N808968 Screw 5 F8DB-18B984-
AAW Speaker Grille-Standard (No Badge)-LH 5 F8DB-18985-
AAW Speaker Grille-Standard (No Badge)-RH 5 F8DB-18K901-
BAW Speaker Grille-Mach-LH 5 F8DB-18978-
BAW Speaker Grille-Mach-RH 5 F8DB-238A35-
AAW Speaker Grille-Blank (No Speaker)-LH 5 F8DB-238A34-
AAW Speaker Grille-Blank (No Speaker)-RH A - Tighten to 6-8 Nm (54-70 lb-in) ------------------
Trim Panel, Door Front
Removal

1. Remove cover behind inside door handle.
   

1. Remove screw from bottom of pull cup retaining front door trim panel to front door (20124).
   

1. Remove three screws retaining front door trim panel to front door.
   

1. NOTE: Do not attempt to remove more than one pushpin at a time.
   
   Using Rotunda Windshield and Molding Trim Removal Kit 107-R0401 or equivalent, remove the door trim panel by pulling one door trim panel pushpin at a time from the inner door skin.
   

1. Disconnect electrical connectors as necessary. Refer to Section 01-14A.
   

Installation

1. Follow removal procedure in reverse order.
   

1. Replace all pushpins with new pushpins (N808994-S).
   

Front Door Trim Panel

remove tha fan speed knob by pulling it out and unscrew the screws beneath it to open the dashboard

YOU PROBABLY WILL REMOVE THE DOOR PANEL TO ACCESS WIRING HARNESS AND MOUNTING HARDWARE!! swampratt200!!AAAEEE!!!

first remove any screws in door panel, then remove lock and window controls, then take flathead screw driver and SLOWLY pry panel off door. You now will have access to speaker. Speaker is held by 4 screws and wire harness that unclips.
Reverse procedure to reinstall. Door panel pops back in the wholes to reattach

Section 15-03: Speakers 1997 Villager Workshop Manual DESCRIPTION AND OPERATION Radio Speakers All vehicle sound systems are equipped with radio speakers (18808) located at all four corners of the vehicle. The radio speakers are mounted in the RH front door (20124) and LH front door (20125), as well as behind the quarter trim panels (31012) in the rear of the vehicle. The Ford Super Sound Audio System has the addition of a subwoofer mounted in the RH quarter trim panel.
-----------------------------------------------------------------------------------------
Radio Speakers, Front Door Removal

1. Remove the front door trim panel (23942). Refer to Section 01-05 .
   

Trim Panel(s), Door Front
Removal

1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
   
2. CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
   Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942).
   
3. Remove the three cover caps and front door trim panel screws.
   

1. Remove the one front door trim panel capped screw from the door pull handle.
   
2. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
   
3. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124).
   
4. Remove the front door trim panel.
   

Door Electrical Connections
Removal and Installation
Refer to Section 01-11 for Power Window, Section 01-09 for Power Mirror, or Section 01-14B for Power Locks. Watershield
Removal

1. Remove the Front Door Trim Panel . Refer to the removal procedure in this section.
   

1. Remove the front door watershield by carefully detaching it from the adhesive.
   

1. Remove the four front door radio speaker screws.
   

you either need a motor or motor and window regulator assembly.
SECTION 501-05: Interior Trim and Ornamentation 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Front Door Trim Panel Removal and Installation

1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .

1. Remove the front door trim panel screws.

1. NOTE: To release the door trim panel two part pin-type retainers, first pull outward on the bottom of the door trim panel.
   Remove the front door trim panel.
   • Disconnect the electrical connectors.

--------------------------------------
SECTION 501-11: Glass, Frames and Mechanisms 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Front Door Window Regulator And Motor
Special Tool(s) Heavy Duty Riveter
501-D011 (D80L-23200-A) or equivalent
Removal and Installation

1. Remove the front door window glass. For additional information, refer to Front Door Window Glass in this section.

1. Disconnect the front door window regulator motor electrical connector.

1. Remove the window regulator rivets.

-----------------------------
SECTION 501-11: Glass, Frames and Mechanisms 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Door Window Regulator Motor Removal and Installation

1. Close the window.

1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .

1. Remove the door trim panel. For additional information, refer to Section 501-05 .

1. If equipped, remove the radio speaker.

1. Position the watershield aside.

1. Disconnect the door window regulator motor electrical connector.

1. Remove the bolts and the door window regulator motor.

---------------------------------------------------

The door panel has to be removed.
To remove the door panel:
Remove cover behind inside door handle.
Remove screw from bottom of pull cup retaining front door trim panel to front door
Remove three screws retaining front door trim panel to front door.
There are pushpins holding the door panel on
Do not attempt to remove more than one pushpin at a time.
Using a trim panel remover to pop the pushpins
remove the door trim panel by pulling one door trim panel pushpin at a time from the inner door skin
Disconnect electrical connectors as necessary
Using a small screwdriver, carefully spread switch retaining walls on window regulator switch plate and remove switch.
To install reverse proceedure.
Hope this helps

No you do not, there will be a small plastic cover over the door mounted tweeter.

Squeeze it with your fingers and you should be able to pop it right off.

There are two screws on the speaker and the others should be visible on removal of the speaker itself.

I suggest you bring a soldering iron or a pair of wire cutters because the speaker wiring is soldered on the speaker and the speaker will not fall back through the speaker frame.