Evaluate 88ft/sec*1mile/5,280ft*3,600sec/hr I do not know how to figure out this problem. can you please walk me throught it step by step? thank you

Have you tried setting the time on your clock? Owners manual should walk you thru the steps.

You have a bad air intake manifold gasket. If it runs idling high, take a can of brake cleaner and spray it on the air intake manifold by the firewall. Spray it right where the air intake bolts on. There are 8 10mm bolts or nuts there. When you spray it while idling, the revs will come down. This makes sure that is the problem before you go any farther. My 02 did the same thing.If you need to know how to change it, let me know, I can walk you through it. It's a one to two hour job, b ut easy

turn on i hope you know that part
adjust the resistance settings like to light then get on and start walking like climbing steps

P0325 knock sensor 1 circuit malfunction bank 1 or 1 sensor, the knock sensor should be check/replaced. You can buy Haynes Repair Manuals at Pepboys that will walk you throught the process step by step.
P0303 is a cylinder misfire in cylinder 3 which may mean it could either be the spark plug, coil or the injector.

How to Reset GM Theft lock Radio's
Article Disclaimer: This article is meant to be used by Delco Radio owners to reset there radios. In no way is it meant to be used for any unethical or unlawful ways.

Purpose
The following instructions will allow you to reset any GM (General Motors), Cadillac, Oldsmobile, Buick, Pontiac theft lock radio.

Requirements
The theft lock radio must be in "LOC" mode.

Procedure:
1. Turn the ignition ON (The radio should display "LOC")
2. Hold down the Radio Presets 2 and 3 buttons for six seconds
3. The radio display changes from LOC to a three-digit number. Write this number down. You now have fifteen seconds to complete the next step.
4. Press the AM/FM button
5. The radio display changes to another three-digit number. Write this number to the right of the first one
6. You now have a six-digit number, the first three digits are from STEP 03 and the last three digits are form STEP 05
7. Call 1-800-537-5140
8. Press 1 then # (pound). You'll hear "Invalid Code, try again"
9. Press 139010 or 106010 or 206010 or 202107 then # (pound). You will be asked to enter your four or six digit code followed by *
10. Enter the number from STEP 6 then *
11. Listen to the four-digit number and write it down. It will be repeated twice
12. Turn the ignition ON (The radio displays LOC)
13. Use the MN and HR buttons to enter the code from STEP 11
14. Press the AM/FM button. The radio display changes to "SEC". Your radio is now "un-locked" and usable.

Dealership Codes
139010
106010
206010
202107

Troubleshooting
If you fail to enter the correct code eight times, the radio goes into INOP mode. You have to wait an hour with the ignition on before the radio returns to LOC mode.

To Read the original article or read similar articles please visit kingbain.com/how-to/unlock-gm-theftlock-radio-s

Good luck (remmeber comment and rated this).

Enter the secret code as follows, pausing no more than 15 seconds between steps:

1. LOC appears when the ignition is ON.
2. Press MIN and 000 will appear on the display.
3. Press MIN again to make the last two digits agree with the code.
4. Press HR to make the first one or two digits agree with the code.
5. Press AM-FM after you have confirmed that the code matches the secret code that was written down. The display will show SEC, indicating the radio is now operable and secure

hi friend,
If you have the security code it's easy. The code is something that either you or a previous owner entered. If you don't have the security code a trip to the dealer will be in your future.
Unlocking the Theft-Deterrent Feature After a Power Loss Enter the code as follows; pause no more than 15 seconds between steps.

1. Turn ON the ignition. LOC will appear on the display.
2. Press MN and 000 will appear on the display.
3. Press MN again to make the last two digits agree with your code.
4. Press HR to make the first one or two digits agree with your code.
5. Press AM-FM after you have confirmed that the code matches the secret code you have written down. The display will show SEC, indicating the radio is now operable and secure.

Entering the incorrect code eight times will cause INOP to appear on the display. Wait an hour with the ignition in the ON position before you try again. When you try again, you will have three more chances (eight tries per chance) to enter the correct code before INOP appears.
Deactivating the Theft-Deterrent Feature Enter the code as follows; pause no more than 15 seconds between steps.

1. Turn the ignition to ACC or ON.
2. Turn OFF the radio.
3. Press the 1 and 4 buttons together. Hold them down until SEC shows on the display.
4. Press MN and 000 will appear on the display.
5. Press MN again to make the last two digits agree with your code.
6. Press HR to make the first one or two digits agree with your code.
7. Press AM-FM after you have confirmed that the code matches the secret code you have written down. The display will show -- -- --, indicating that the radio is no longer secured.

Entering the incorrect code will cause SEC to appear on the display. The radio will remain secured until the correct code is entered. When battery power is removed and later applied to a secured radio, the radio will not turn on and LOC appears on the display. To unlock a secured radio, refer to "Unlocking the Theft-Deterrent Feature After a Power Loss".

hope this helps u
please rate me..............
thank u for using fixya
regards
sivvaranjini

Yes it needs a thermostat. What size engine?

Gasket = $35 (permatex rubber)
Labor - my manual says 3 hours.
You'll have to be responsible for figuring out the labor price per hour depending on where you are located.
In MI, a garage is about $50/hr, and dealership = $85/hr
CA might be $95/$150/hr.

Parts are minimal on the job - its all labor.
Figure in about $20 for shop supplies... gasket remover, sealant, rags, etc.

Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

ignition on, LOC appears
press MN and OOO will appear in display
press MN again to make the the last two digits agree with your code.
press HR to make the first one or two digits agree
with your code.
Press AM/FM after you have confirmed that the code matches the code you have written down.
The display should show SEC which indicates
the radio is now operable and secure.
'rock on'