1995 GMC Sierra C1500 Logo
Bob worthy Posted on Feb 11, 2013

95 gmc c1500 third brake lite works but cargo won't

Third brake lite works but cargo won't good bulbs and fuse

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Corporal:

An expert that hasĀ over 10 points.

  • Contributor 1 Answer
  • Posted on May 03, 2013
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Corporal:

An expert that hasĀ over 10 points.

Joined: May 03, 2013
Answers
1
Questions
1
Helped
2138
Points
21

The cargo light will only work if the lights in the cab are on. Turn them on then flip the switch for the cargo light and it should come on, if not then it is probably an electrical problem.

  • csmith1120 Feb 28, 2022

    WHICH FUSE CONTROLS THE CARGO LIGHT,,

×

5 Related Answers

Anonymous

  • 375 Answers
  • Posted on Jun 29, 2008

SOURCE: 1998 gmc sierra brake lights

did u check that they not burn?if not you should Check the wires going into the steering column if you don't have separate turn signal lights and brake lights because if they use the same bulb then the turn signal may be bad. If I remember correctly that particular car doesn't work this way, but I include it just in case.

Ad

Anonymous

  • 1 Answer
  • Posted on Oct 13, 2008

SOURCE: Brake lights don't work.

Brake lights do not work. Turn signals do work.

emissionwiz

Marvin

  • 85242 Answers
  • Posted on Nov 07, 2008

SOURCE: Brake lights do not work

This is a well documented problem, replace the turn signal/multifunction switch to correct this issue, this very problem happened on my GMC, it is a 99 as well, replaced the switch as instructed by a chevy forum member and it fixed the problem

Anonymous

  • 426 Answers
  • Posted on Nov 19, 2008

SOURCE: 98 gmc suburban brake lights

One of two things cause this corroded or poor chassis earth at the bulb holders or the circuit board that holds the bulb is faulty.

Anonymous

  • 1986 Answers
  • Posted on Aug 13, 2009

SOURCE: how do you remove the third brake light assembly

You'll have to gently apply some prying pressure to the housing as you turn the screws, it sounds like they've stripped the part they go in...

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Third brake light

stand on truck bed.the cargo lamp housing held in place by two screws.just remove the two screws holding cargo lamp housing replace bulb.
0helpful
2answers

Brake lights won't work

Check the voltage or the connection.
__________
Multi-Cardiag M8 CDP for car and truck
1helpful
1answer

Third brake lite [ fused or bulb]

Should be on the same circuit as the regular brake lights.
2helpful
1answer

I have a 2004 silverado. My cargo light isn't getting any power. My third light works fine and when i reverse the harness the cargo lights work. I'm assuming its in the wiring. Do the two wir

There should be 12 volts on the orange wire at the bulbs. The switch controls the ground side of the circuit. There should be 12 volts on the blue w/white wire at the switch. The switch will ground that wire and complete the circuit and the cargo lights will turn on.

to check the switch you would unplug it and check for continuity between the pins that the blue w/wire wire and black wire go to.

Iā€™m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

1helpful
3answers

Brake lights keep blowing a fuse on a 1997 GMC suburban

i have a 95 gmc suburban that keeps blowing the fuse when break is aplied i even disconected the back lights and it does the same what could it be
0helpful
1answer

Brake lights dont work,fuse good ,bulbs good,third light works

The third brake light switch works off a module for it is a sealed unit with a inverter that takes 12 volts beefing the voltage to 110 volts for the light emitting diode lights in it. It these terms you will need a new brake light switch located by the brake pedal
0helpful
1answer

2000 chevy 3/4 ton diesel no brale light but third brake light wo

I just Know that you replaced the bulb ,try a test lite ,make shure it's grounded well poke inside the socket for the bulb this metal socket gives the bulb both electric and a ground ,this is the problem,good luck.
0helpful
2answers

Rear turn signals and brake lights out. Front signals and rear tail lights work fine.

the brake lights and the rear turn signals should be the same bulb check the bulbs to make sure they are not blown does your third brake light work if all brake light are out and the bulbs are good check the brake light switch on the brake pedal
Not finding what you are looking for?

2,148 views

Ask a Question

Usually answered in minutes!

Top GMC Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...