2006 chevy express 2500. While changing the brakes on my van, a rivet and clip pulled through the rear wheel dust plate, I'm unsure on how to fix this as now one half of the shoe is rubbing agains

Looks to be easy unless someone has replaced the screws with something else?

The bulb is a small capless push in bulb.

2013 Chevrolet Express 2500 License Plate Light Mini Bulb

AutoZone.com https://www.autozone.com > electrical-and-lighting > 2... Equip cars, trucks & SUVs with 2013 Chevrolet Express 2500 License Plate Light Mini Bulb from AutoZone. Get Yours Today! We have the best products at the right

express 1500, 2500 or 3500
USA car? or not?
ABS?????
wws= wheel speed sensor.
sure and is in the manual to read at any time.
AWD OR RWD CAR, ALL WHEEL OR REAR WHEEL DRIVE?

AT THE REAR OF THE CAR AT DISKS. IS FLEX CABLE
there 1500 there is a large flex cable, this is emerg. brake cable
there is brake hose flex rubber hose, this is not it either
then the small wire elect cable (with snap connectors) this is it.

same on most cars made, 4 speed sensors, 2 front 2 rear
all look kinda the same but are not.exactly.

Remove the rear differential cover. You will see a large pin in the center that has to be removed, spin the diif until you see the bolt that holds it in. The pin should just slide right out. Assuming tires are off. Push the axle towards the center. On the end of the axle is a c clip that has to come out. Magnetic works well for these. Pull the axle out. Remove the bearing. There are special tools to get them out.

Sounds like a bad turn signal switch. I bet if you wiggle the turn signal lever while you have your foot on the brake pedal the left and right brake lights ill intermittently work.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Make sure the mechanic checked the park brake shoes inside the rear rotors, they quite often break away from the lining and get wedged in the rotor, sometimes causing a constant squeal noise. I've also seen the brake pad anti-rattle metal clips become loose and wander in the caliper bracket, they lightly rub against the rotor and cause a squealing noise similar to worn brake pads. They are also very bad for the backing plates rusting out prematurely and rubbing on the inside of the rotor. Other than that he can just try to champher the edges of both front and rear pads to help dissipate the brake dust, from collecting and causing squeak noises.

The pad drums of your 2000 Dodge Grand Caravan can wear with use. Heat buildup in the brakes can glaze, warp or crack the drum. If that happens, replacement of the drum is the only way to fix it. In most cases, you can remove the rear drums, replace them with a new set and leave the existing shoes on the van. Take a minute and inspect the brake shoes thoroughly while you have the drums off the van.

1. Loosen the lug nuts on the rear of your 2000 Dodge Grand Caravan with a lug wrench. Do not take them off the wheel studs.
2. Raise the rear of the van with a jack and support it on a set of jack stands. Place the stands under the rear suspension, making sure they are secure. Remove the lug nuts from the wheel studs and pull off the rear wheels.
3. Check the rear drum where the wheel studs come through for retaining clips. These are used during the manufacturing process; and if they are still on your van, they need to be removed. Pry the clip off the wheel stud with a flat head screwdriver and discard them. Most vehicles will have two clips on each brake drum.
4. Grasp the brake drum on the outer edges and pull it straight off the wheel studs and brake pads. Discard the old drum and slide the new drum into place, aligning the holes in the drum with the wheel studs. Push the drum in until it seats completely. Repeat the process on the opposite side of the van.
5. Position the wheel back on the wheel studs and install the lug nuts by hand. Raise the back of the van with a jack and remove the jack stands from under the suspension. Lower the van to the ground and tighten the lug nuts with a lug wrench.

You have to remove the upper applique to remove the tail lamp, it is the trim panel above the lamp. I think it is held in place by two nuts/bolts but not sure. You have to have the rear doors open to remove it

bad master cylinder seal must replace master cylinder

i own a 2006 chevy express cutaway box truck the interior box lights are not working and i do not know what fuse designates them can any one help me locate the proper fuse

Dust shield. Call the Ford Dealer. They are the only place you can get parts like that.