2009 Jeep Liberty Logo
Anonymous Posted on Nov 17, 2012

2009 jeep liberty hazard lights don't turn on

Hazard lights (all console switches) don't work.. interior light either.

  • 2 more comments 
  • Anonymous Nov 19, 2012

    I checked the obvious ones already (interior light).. and several others.. guess i'll pull them all. There wasn't one called "console cluster" or whatever or hazard switch.

  • Anonymous Nov 21, 2012

    Did you all so check the ones in the engine compartment fuse block, All so they might be control buy a relay That is located in the fuse block in the engine (Compartment,) My only suggestion is call a dodge dealership end ask to talk to some one in the service department about the (Problem)

  • Anonymous Nov 21, 2012

    Yeah... as far as I know there's only one place for the fuses.. in the engine compartment, between battery and firewall... I will check them all this holiday weekend and post back what I find out.. if I can't find anything.. then I will take your advice and leave it to a pro.. Thanks!

  • Anonymous Nov 21, 2012

    Call the dealer ship where you live most dealerships are verry help full now a days,

×

2 Related Answers

Anonymous

  • 186 Answers
  • Posted on May 16, 2009

SOURCE: 2009 Jeep Grand Cherokee Laredo interior lights won't turn on

check your light dimmer & see if you have it set all the way down.If it's anything like my 99WJ it has an off setting when the dimmer is set all the down causing the interior lights to not come on when you open the doors,hope this helps

Ad

Anonymous

  • 15 Answers
  • Posted on Oct 04, 2009

SOURCE: my jeep wrangler hazard lights, turn signals and

replace the flashers, check fuse, check that the switch is grounded properly

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

2006 Jeep Liberty , hazard lights not working turn signals out too. turn signals are fused separate left om one fuse right on another, any ideas

You need to check the power with an electrical screwdriver. Start with the turn signals. Did the bulbs blow.? If so there is a serious electric fault and it will get worse. Has the jeep been through flooding? Thearth connections may be damp. You may need to use a hair dryer to fix them.
0helpful
1answer

Hazard roads light will not turn off on dash

wiggle it over and over, it will go off. many are just funky junky switches
not for much usage. day to day. so are , cheap.
never seen one i could not unstick yet, spary electric spray cleaner in the switch (at gaps) and cycle it. bingo. fixed.
2helpful
1answer

2000 tacoma flashers don't work but turn sig do work!

The hazard switch gets power from the horn fuse which is hot all the time, and from the turn signal fuse which is hot when the key switch is on. The turn signal switch gets power from the hazard switch and both use the same flasher.
So if the turn signals work but the hazard switch does not power the lights, and both fuses have power, I would say the problem is inside the hazard switch.
0helpful
1answer

The hazard lights buzz and don't work.

if fuse okay,could have faulty multifunction switch.
1helpful
1answer

I changed the fuse as the turn lights and hazard lights were not working but all other light including brake and interior worked. Now the hazard light stays on and I cannot turn it off. can you Help p

if your hazard lights stay on, you may have a problem with the hazard switch on your stearing collum. try moving it back & forth several times, eg. on, off, on, off always ending @ off & see if that works. they do get sticky @ times. your brake lights will work but your turn signals won't work properly with the hazard switch turned on. let me know if problem persists & will see if i can help you more. good luck.
1helpful
1answer

Brake lights & Hazzard lights don't work; fuse ok... High mounted center brake light works... Turn signals work...suspect problem is multifunction lever Power drain to battery constant...2...

As for the brake lights push brake pedal down while pushing on and wiggling the hazard switch.If the brake lights come on then replace the multi-function switch.
0helpful
1answer

My rear hatch light indicates that the hatch is open which it is closed tight. Because of this my interior lights stay on and my remote start won't work. How can I fix this? My jeep is the 2009...

The switch on the latch is more then likely stuck. If you can see it spray it with some electrical cleaner and open and shut the hatch a few times.
Not finding what you are looking for?

709 views

Ask a Question

Usually answered in minutes!

Top Jeep Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...