They are actually in the fuel tank. Here is a link that states how to replace it in step by step instructions. Hope this will help you.
http://www.club-tc.com/threads/fuel-pump-removal-install.3793/
SOURCE: 07 scion tc passenger window wont roll down when lock by driver..
thats cause that what the lock is for so it wont go down
SOURCE: Where is the 2005 Scion Xa's air filter located?
Hi...
The Air Filter on your SCION Xa .
Is located at Engine compartment DRIVER side. Near the battery
If you follow the Big rubber hose comin from the intake goin to a Black box.
The black BOX. The Plastic Black BOX Has a few metal Clips. to Open.
Inside is the Air Filter...
I hope this help on your question.
Thank you for use fixya..
SOURCE: How do I reset the check engine light for a 2006 scion tc?
YOU CAN GO TO ANY ADVANDED AUTO PARTS AND THEY CAN HOOK UP A OBD2 SCANNER, WE THEY DO ASK THEM TO RESET THE LIGHT FOR YOU.. THIS IS A FREE SERVICE TO THE PUBLIC..GOOD LUCK KEITH..
SOURCE: How to remove front stabilizer bar in '05 Scion TC
I don't know if you can get the bushings out without changing the bar or not, but changing the bar is a big job for a DIY. I was thinking about it but will probably have a pro do it for me. From the shop manual:
1. PLACE FRONT WHEEL FACING STRAIGHT AHEAD
2. REMOVE COLUMN HOLE COVER SILENCER SHEET
(See page SR-9)
3. DISCONNECT NO. 2 STEERING INTERMEDIATE
SHAFT ASSEMBLY (See page PS-21)
4. DISCONNECT NO. 1 STEERING COLUMN HOLE
COVER SUB-ASSEMBLY
5. REMOVE FRONT WHEEL
6. REMOVE ENGINE UNDER COVER LH
7. REMOVE ENGINE UNDER COVER RH
8. REMOVE FRONT STABILIZER LINK ASSEMBLY LH
(a) Remove the 2 nuts and front stabilizer link LH.
HINT:
Use a 6 mm hexagon wrench to hold the stud if the
ball joint turns together with the nut.
9. REMOVE FRONT STABILIZER LINK ASSEMBLY RH
HINT:
Use the same procedures described for the LH side.
10. DISCONNECT TIE ROD END SUB-ASSEMBLY LH
(See page DS-6)
11. DISCONNECT TIE ROD END SUB-ASSEMBLY RH
(See page PS-21)
12. DISCONNECT PRESSURE FEED TUBE ASSEMBLY
(See page PS-21)
13. DISCONNECT FRONT SUSPENSION NO. 1 LOWER
ARM SUB-ASSEMBLY LH (See page SP-22)
14. DISCONNECT FRONT SUSPENSION NO. 1 LOWER
ARM SUB-ASSEMBLY RH
HINT:
Use the same procedures described for the LH side.
15. REMOVE FRONT FLOOR PANEL BRACE (See page
EX-2)
16. REMOVE CENTER EXHAUST PIPE ASSEMBLY (See
page EX-2)
17. REMOVE HOOD SUB-ASSEMBLY
18. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY
19. SUSPEND ENGINE ASSEMBLY (See page MX-19)
20. REMOVE NO. 1 HOOK (See page PS-22)
21. REMOVE FRONT SUSPENSION CROSSMEMBER
SUB-ASSEMBLY (See page PS-22)
22. REMOVE FRONT NO. 1 STABILIZER BRACKET LH
(a) Remove the 2 bolts and front No. 1 stabilizer
bracket LH from the suspension crossmember.
23. REMOVE FRONT NO. 1 STABILIZER BRACKET RH
HINT:
Use the same procedures described for the LH side.
24. REMOVE FRONT NO. 1 STABILIZER BAR BUSH
(a) Remove the 2 No. 1 stabilizer bar bushes from the
stabilizer bar.
25. REMOVE FRONT STABILIZER BAR
You can download the manual online for about $15. Well worth it.
5,201 views
Usually answered in minutes!
×