I have a subaru impreza (95) reg, my heater is blowing cold air and my temp gage is on red, the in let hose to rad is hot and the out going hose is cold. what do you think is the problem?
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
once the truck is fully warmed up, feel the 2 heater hoses going through the firewall in the engine compartment. they should be hot to the touch. if they are, then the problem is most likely the heater controls, such as the temp. switch on the dash or the blend door itself inside the dash. if they are cool, check that the coolant is completely full. just because the temp gauge reads normal doesn't mean there's enough coolant in the system to fill the heater core. remove the radiator cap once cooled and top off if needed. if it is, or was, low, its possible to get air the the cooling system and block flow of coolant to heater core.
If the hoses to the rad is hot the chances are there is an air lock in the heating core. The best place to bleed the air out is at the top. If there is no provision for bleeding air you will have to slacken the hose and manipulate it to allow water/air out.
Make sure for safety's sake the engine is cold to prevent scalding yourself. Have an assistant topping up the engine rad while you are working on the bleeding operation
Did you run engine from cold, WITH HEATER ON, and fill cap off when re-filling system? If not, try that and see what happens. Let the engine get up to operating temperature and rad fan come on to cool 2 or 3 times before putting cap back on.
WELL IS YOU COOLANT LEVEL RIGHT AND IF SO WHEN TRUCK IS WARMING UP CHECK THE RAD HOSE'S AND SEE IF THE LOWER ONE IS GETING WARM ARE NOT OR IF THE TOP IS COLD BUT I WOULD START WITH THERMOSTAT IT'S SOUNDE LIKE IT IS COUSE FLOW ISUSSE HOPE THIS HELPS BUT IF BOTH HOSE ARE HOT AND YOU TOUCHE HEATER HOSE ONE HOT THE OTHER IS NOT THEN IT COULD BE HEATER CORE ISUSES
sounds more like a possible heater core issue the heater core is what heats your car by the fan blowing over it and through tour vents ! find the 2 hoses that come out of your firewall on the back side of the engine compartment . run vehicle for 10 to 15 min and see if both of the hoses are hot if one is hot and one is cold heater core is plugged. if both hot have a diff problem. start hear first !!
if the engine temp seems normal on the dash gauge then it may be a clogged heater core.have the sysyem flushed-it worked for me recentlythe other options may be a heater door not closing..some are vacuum activated a flush is a good place to start..good luck
you should have hot water on all rad. hoses when the motor is running at a norm. temp. the water is not going through the heater core like it should. you have cutoff valve bad low water are a stopped heater.try a hoter thermostat if none of the above are true.
Did you bleed the air oout of the cooling system - Their is a bleeding next to the therostat housing.
1 - When the vehicle is cold remove the rad(tank) cap and top up the level if needed
2 - start the vehicle with the rad cap off and leave the car run until you can see that the therostat has openned(look in tank/rad) to see fuild flow then open the bleeder slowly to let any air out of the cooling system. Once you have coolant flowing out of the bleeder close the bleeder and install the rad/tank cap.
NOTE - Be careful with the engine running and hot Coolant.
You make need to bleeding system 2-3 time to get all the all out. Once all the air is out of the system you problem should be solved. If air returns to the coolant system have the system checked for possible head gasket leaking air into the coolant system
×