- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
How to Adjust a Headlamp Beam on a 2005 Chevrolet Cavalier...
When you replace the headlamp assembly in the 2005 Chevrolet Cavalier, you must also adjust the headlamp beams. Like most vehicles, there are two screws located on the headlamp assembly that control the vertical and horizontal direction of the headlamps. Proper adjustment is necessary for adequate visibility during nighttime driving; bad adjustment can make it difficult for you to see or make it difficult for oncoming drivers to see, creating a potentially dangerous situation. You can adjust the headlamp beams yourself with a screwdriver in about 15 minutes. Park the Chevrolet Cavalier on a flat surface facing a wall or garage door approximately 15 feet away. Park the Car so that it is perpendicular to the wall.
Lift the hood and remove the plastic trim panel above each of the headlights. There are three plastic fasteners that secure the trim panel; pry the fasteners out using a flathead screwdriver. Lift the trim panel up to remove. There are two adjusting screws beneath the trim panel, one on the top of the headlamp assembly and one along the outer side of the headlamp assembly.
Turn the headlights on so that they shine on the wall. Ensure the headlights are on the "dim" setting.
Adjust the vertical bolt, located on the top of the headlight assembly near the center of the vehicle to raise or lower the headlight, using a crosspoint screwdriver. Turn the screw counterclockwise to lower the headlamp beam; turn the screw clockwise to raise the headlamp beam. Adjust the headlamp so that the beam is below a driver's eye level.
Adjust the horizontal bolt, located on the outer side of the headlamp assembly to move the headlamp beam right of left, using a crosspoint screwdriver. Turn the screw counterclockwise to move the headlamp beam right; turn the screw clockwise to turn the beam left. Adjust the headlamp so that the beam shines straight ahead or slightly toward the center of the vehicle.
Replace the plastic trim panel and fasteners and close the hood. Warning: raising the lights too high can make it difficult for other drivers to see you.
some times headlamp units have a plastic retaining clip on the underside of headlamp, does the headlight move from side to side? try to pull the headlight back from the top of unit then lift up the headlamp unit, if not it could be the headlamp adjusters holding unit in place.
I have a 2002 Impala, which should have the same headlights.
The headlight assembly is removed very easily.
There are two plastic tabs on the top of each headlamp. Pull both tabs straight up about 1 inch. The headlamp assembly will slide straight forward from the car.
Then you can remove bulb from the assembly.
There are 2 tabs that stick out just behind the headlamp assembly.Pull up on both of them and then just pull the headlamp assembly out.Now you can replace the bulb.Check to see if it works before reinstalling the assembly.Hope this helps.Good luck.
ithere are 4 bolts that hold it in...the top 2 are obvious..the others are behind the bumper. the bumper must be removed to acces them...here are the manuals instructions..
Item
Part Number
Description
1
—
Headlamp assembly bolts (3 required)
2
—
Headlamp assembly nut
3
13008
Headlamp assembly
4
14290
Electrical connectors Removal and Installation NOTE: Make sure the headlamp switch and the ignition switch are in the OFF position.
Remove the front bumper cover. For additional information, refer to Section 501-19.
Remove the 3 headlamp assembly bolts.
To install, tighten to 5 Nm (44 lb-in).
Remove the headlamp assembly nut and the headlamp assembly.
Are you still looking for help with replacing headlights for 2005 VW.
If so , I have to replace mine tomorrow , I can photograph the process if that helps..
×