Need torque spec's for 1999 Grand Am 2.4L motor valve pan gaskets bolts? thanks

12-13 foot pounds

Pontiac Engine Torque Specs

Butler Performance https://butlerperformance.com > p-34888-pontiac-engi...
Pontiac Engine Torque Specs ; Oil Pump Cover Bolts, Engine Oil, 15 ft-lbs. ; Windage Tray, Engine Oil, 15 ft-lbs. ; Oil Pan, Engine Oil, 12 ft-lbs. ; Camshaft ...

Oil and Transmission Pan Bolts. How much torque?

GMForum.com https://www.gmforum.com > ... > 1992-1999
Jun 12, 2003 - the Torque Specifications for the Xmission Oil Pan Bolts are 12-13 Ft. Lbs. Works for me.

Transmission pan Torque spec
Apr 28, 2017
4T65E-HD transmission pan bolt torque values
Feb 8, 2008
More results from www.gmforum.com

2004 Pontiac Sunfire 2-dr Transmission Pan Gasket ...

MyCarSpecs https://www.mycarspecs.com > pontiac > sunfire > 2004
The transmission pan gasket helps to seal in transmission fluid and keep it from leaking everywhere. This will degrade over time and need replacement, ...

..

Bobby, oil pan bolt torques for 4.0 Wrangler. Oil Pan Bolts 1/4 84 in-lbs Oil Pan Bolts 5/16 132 in-lbs As far as sequence, see last link, start in center, criss cross pattern tighten snug all, then repeat to torque spec.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Oil Pan Gasket leaking
http://jeephorizons.com/tech/99_40l_torque_specs.html
98 jeep 4 0 oil pan bolt torque sequence specs Google Search

Torque specs on on 4L60 tranny pan in 04 escalade??

www.cadillacforums.com/.../cadillac-escalade.../260881-torque-specs-4l6...
May 26, 2012 - 3 posts - ‎3 authors Has 104000 miles on it now, figured it's time to change the filter and the fluid. ...Cadillac Escalade, EXT and ESV Forum - 1999 - 2006 Discussion, ... Flywheel toTorque Converter Bolt ... Transmission Fluid Pressure Manual Valve Position Switch to Valve Body Bolt ... Powered by vBulletin® Version 4.1.5 Re: SRX V8 Valve Cover Gasket Replacement Write Up ...
14 posts
Jun 10, 2015
2000 DTS Setting up Internal Mode Switch - 4T80E ...
9 posts
Aug 27, 2014
More results from www.cadillacforums.com

valve cover gasket torque spec? - Bimmerforums

www.bimmerforums.com/.../showthread.php?...valve-cover...torque-spe...

Dec 7, 2012 - Remember the little rubber grommets around the cover bolts? ... Location: alabama; Posts: 5,537; My Cars: 2002 bmw 325 ... Torque spec for the M52 valve cover bolts is 89 inch-pounds / 7.4 ... 1976 - 1989 (E24) · 2004+ (E63, E64) ... 2012+ X1 (E84) · 2003+ X3 (E83,F25) · 1999+ X5, X6 (E53, E70, E71). Valve Cover Bolt Torque Specs
Oct 25, 2014
Valve cover screw torque specs?
Nov 9, 2012
leaking valve cover gasket
Dec 29, 2011
How specific for torque specs?
Dec 27, 2011
More results from www.bimmerforums.com

Caravan, Grand Voyager, Town and Country, Voyager, 2000-2004

Oil Pan - Removal & Installation

2.4L Engine

1. Before servicing the vehicle, refer to the Precautions Section.
2. Drain the engine oil.
3. Remove or disconnect the following:
   Negative battery cable Structural collar A/C compressor bracket to oil pan bolt Oil pan
4. Clean the oil pan and all gasket mating surfaces.

To install:

1. Install or connect the following:
   Oil pan gasket to the block after applying engine RTV at the oil pump parting line Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Structural collar Negative battery cable
2. Fill the crankcase to the correct level.
3. Start the engine, check for leaks and repair if necessary.
   

3.0L Engine

1. Before servicing the vehicle, refer to the Precautions Section.
2. Drain the engine oil.
3. Remove or disconnect the following:
   Negative battery cable Starter motor Front motor mount bracket Bending braces Torque converter dust shield Oil pan
   
   
   Fig. Oil pan mounting bolt tightening sequence-3.0L engine
   

To install:

1. Clean the oil pan all mating surfaces.
2. Apply RTV gasket material to the oil pan.
3. Install or connect the following:
   Oil pan. Tighten the bolts in sequence to 50 inch lbs. (6 Nm). Torque converter dust shield Bending braces Front motor mount bracket Starter motor Negative battery cable
4. Fill the crankcase to the correct level.
5. Start the engine, check for leaks and repair if necessary.
   

3.3L & 3.8L Engines

1. Before servicing the vehicle, refer to the Precautions Section.
2. Drain the engine oil.
3. Remove or disconnect the following:
   Negative battery cable Engine oil dipstick Drive belt splash shield Strut to transaxle attaching bolt and loosen the strut to engine attaching bolts Transaxle case cover Oil pan fasteners Oil pan and gasket

To install:

1. Clean the oil pan and all mating surfaces.
2. Apply a 1 / 8 inch bead of gasket material at the parting line of the chain case cover and the real seal retainer.
3. Install or connect the following:
   New gasket on the oil pan Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Transaxle case cover All bending brace bolts Drive belt splash shield Engine oil dipstick Negative battery cable
4. Fill the crankcase to the correct level.
5. Start the engine, check for leaks and repair if necessary.

Hope helps (remember rated this).

Fig. Cylinder head bolt tightening sequence-3.1L engines & 2001-04 3.4L engines




Fig. Cylinder head bolt tightening sequence-2005 3.4L engines



Hope this help (remember rated and comment this).

The torque spec is 14 Newton Meters or 124 Inch Pounds. You may consider replacing the gasket. That is one of the easiest ones to do.
Good luck

It is actually 10 ft lbs. This is something that you want to tighten to exact specs.


Hope this helps!

The tightening is less torque, buyt rather gasket and pan squish.... barley gets tight, but too much and leaks happen.

Be certain to reform the pan bolt holes before you replace the pan.

So tightening happens evenly and stop just as the gasket shows deformation. This is after even tightening 2 or 3 steps....

torque specs for these bolts can be found in a Haynes or Chilton manual availiable from your local parts store, or maybe at your local library, however these bolts are usually no more than 14 ft pounds, unlike cylinder head bolts, the bolts do not need to have any stretch factor to hold the oil pan gasket in place or sealed.