What does trouble code p0463 relates to for a 2000 daewoo nubira ?
SOURCE: 2000 daewoo nubira brake light problem.
Thanks to your advice my problem is solved. A big fixya is in order. Thanks again
SOURCE: timing marks for a daewoo nubira cdx
Here is a pic if the timing marks two small marks on the cam pulleys and one small cut away on the crank pulley .
SOURCE: replacing timing belt on daewoo nubira 2000 model
Instructions
Difficulty: Moderate
Things You’ll Need:
Step1
Raise and support the vehicle
on jack stands. Remove the intake air temperature wiring, the breather
hose and intake air hose. Take off the air cleaner assembly.
Step2
Remove the right wheel. Remove the accessory belts. Remove the
crankshaft bolt and the crankshaft pulley. Remove the power steering
bolts and the timing belt covers. Temporarily install the crankshaft
bolt and turn the engine clockwise until the mark on the crankshaft
pulley, which is a triangle stamped into the crank sprocket, is aligned
with the corresponding triangular mark on the block.
Step3
Make sure that the timing marks are aligned on the camshaft sprockets.
These are a line on each sprocket that runs through a tooth on each
sprocket. These lines should line up in the middle between each
sprocket and point toward each other. If they do not line up, turn the
crankshaft one more time and they will line up. It takes two turns of
the crank to one complete revolution of the cam.
Step4
Loosen the water pump bolts; using the 3/8-inch ratchet, turn the water
pump clockwise away from the belt and loosely tighten the bolts to keep
it there. Remove the timing belt.
Make sure the timing marks are aligned and install the new belt
starting on the right side from the crank sprocket and working
counterclockwise. Keep all the belt tension on the right side away from
the tensioner.
Step5
Loosen the bolts in the water pump and rotate the water pump
counterclockwise to apply tension to the belt. Watch the tensioner,
which is above the water pump, and apply tension with the water pump
until the pointer on the tensioner lines up with the notch above it.
Lightly tighten the water-pump bolts.
Step6
Turn the engine
two more times and align the timing marks perfectly. Loosen the
water-pump bolts and, using the ratchet, apply tension to the belt
until the tensioner pointers are aligned. Tighten the water-pump bolts.
Step7
Install the timing-belt covers and the bolts in the power-steering pump
and tighten. Remove the crankshaft bolt and install the crank pulley
and the bolt, then torque the crankshaft pulley bolt to 70 foot pounds
of torque. Install all components in reverse order of removal.
SOURCE: 2000 daewoo nubira need serpentine belt routing
The following link will take you to a diagram for your car. Best of Luck!
Greg
http://www.mvreader.com/multiview/dayco/zoom.php?zoom_item=C0000B&l=n&catalog=auto&category=2
SOURCE: no interior heat in my 2000 daewoo nubira
3 possible issues here,
the first is that your thermostat is stuck open, when this happens the air will barely be warm, luke warm at best, replacing the thermostat will fix this problem
the second, is that you have low coolant levels, when your coolant levels are way low, your heater core doesn't get the proper amount of coolant (if any) and the system blows cold air instead of heated air.
The third and final possibility, is that your heater core has clogged up (usually happens when stop leak or some type of radiator sealant is used) when this happens you can feel warm air when accelerating (test this by gently reving the vehicle and holding the rpm's when it is in park and holding your hands over the defrost vent to check for heat.
If you can tell me what symptom your vehicle is having I can help with instruction on how to fix it thanks [email protected]
Testimonial: "The solutions provided were spot on. I was particularly impressed with the list of potential problems and solutions offered for each"
503 views
Usually answered in minutes!
×