Windshield wipers on Saturn will not work. Motor runs but no linkage to wiper arms.

It Sounds Like, Either The Arms Are Loose ,If You Can Hear Something Moving Behind The Dash,
Or The Linkages Are Seized ,If The Motor Just Hums No Movement Heard,In Which Case Try Spraying Q 20 On The Linkage And Try Moving The Wiper Arms By Hand To Get It Going Again,
If Not The Motor May Just Be Burn;t Out.

their is three main components to your windshield wipers. their is the wiper arms, linkage and motor. Check the linkage at the motor. you can find this ether under the hood or by removing a cover that is between your windshield and hood. The linkage has bolts or allen screws that hold them on the motor and the wiper arms they may be loose. it could also be bushings that are in between the two linkage rods it could be warn out and caused the linkage to seperate. Hope this helps

Wiper Motor

Removal & Installation

1. Disconnect the negative battery cable.
2. Disconnect the wiper motor electrical connector.
3. Remove the four mounting bolts securing the motor to the firewall.
4. Using a suitable prybar, carefully separate the wiper motor from the wiper linkage and remove the motor.

To install:

1. Attach the wiper motor ball joint to the wiper linkage.
2. Position the motor on the firewall and secure the motor with the four mounting bolts. Tighten the mounting bolts to 75 ft. lbs. (102 Nm).
3. Connect the electrical connector.
4. Connect the negative battery cable.

How do I get to the windshield wiper motor on a 1990 Jeep Wrangler?

Take linkage loose and run wiper motor one turn. You've got the motor and linkage "out of time" .

sounds like a loose nut. there are nuts that hold the wiper arms on, they may be under a cover but theyre at the base of the wiper arm. also there's a nut that holds the wiper linkage onto the wiper motor. if you can move the wipers independently, it's the nuts connecting the wiper arms.if you move one arm and the other moves with it, it's the nut holding the linkage to the motor.

why do you think the motor still works if the wipers don't move? Can you hear the motor run or can you see a little movement when you turn the switch on?

What happens when you activate the washers?

go to a salvage yard that allows you to remove the parts yourself. Then you can see how the motor and linkage assembly comes out.


don't have 1983 info, but here is 1994:

Section 01-16A: Wiper and Washer System, Ranger/Explorer 1994 Ranger and Explorer Vehicles Workshop Manual
DESCRIPTION AND OPERATION Windshield Wiper System, Ranger/Explorer The windshield wipers are actuated by a permanent magnet, rotary-type electric windshield wiper motor (17504) . The two windshield wiper pivot arms (17526) and windshield wiper blades (17528) are mounted on a pivot shaft, one at each side of the windshield. The windshield wiper mounting arm and pivot shaft (17566) are connected to the motor by windshield wiper adapter and connecting arm clip (17531) . Ranger and Explorer vehicles are equipped with an interval wiper and washer (IWW) system featuring a lever-type turn signal and windshield wiper switch (13K359) mounted on the steering column. The IWW windshield wiper governor (17C476) uses a relay contact to control current to the windshield wiper motor . The governor electronic circuitry controls the contact to supply current to windshield wiper motor . A rear wiper/washer system is available on Explorer vehicles. The rear window wiper system consists of a windshield wiper motor mounted inside the liftgate (40010) , an articulating windshield wiper pivot arm and windshield wiper blade , a windshield wiper/washer switch (17A553) and an inline circuit breaker. The front electric windshield washer system consists of a control switch, integral with the turn signal, a windshield washer reservoir (17618) and windshield wiper motor and the necessary windshield washer hoses (17A605) , windshield washer nozzle jet and brackets (17603) and attaching parts.
------------------------------------------------------------------------------------------------
Pivot Shafts and Linkage Removal and Installation
NOTE: The left and right pivot and windshield wiper adapter and connecting arm clip assemblies are serviced separately.

1. Perform Steps 1 through 9 of Windshield Wiper Motor Removal as described in this section.

1. If servicing left windshield wiper adapter and connecting arm clip , remove left windshield wiper mounting arm and pivot shaft and windshield wiper blade assembly.

1. Remove left windshield wiper adapter and connecting arm clip access cover.

1. Remove left pivot nut, lower windshield wiper adapter and connecting arm clip and slide it out through left access opening. For installation, follow removal procedures in reverse order. Tighten nut to 10-13 Nm (7-10 ft-lb). Make sure the clip is fully seated in the windshield wiper adapter and connecting arm clip . Do not try to install clip with windshield wiper adapter and connecting arm clip on motor crank pin.
   

----------------------------------------------------------
Windshield Wiper Motor Windshield wiper motor are not serviceable. If worn or damaged, the windshield wiper motor must be replaced as an assembly. Removal

1. Cycle windshield wiper blades until in straight-up position and turn ignition switch OFF.

1. Disconnect battery and wiper motor electrical connector.

1. Remove the right windshield wiper mounting arm and pivot shaft and windshield wiper blade .

1. Disconnect the battery ground cable (14301).

1. Remove the right pivot nut and allow the windshield wiper adapter and connecting arm clip to drop into the cowl top outer panel .

1. Remove the linkage access cover, located on the right side of the dash panel near the windshield wiper motor.

1. Reach through the access cover opening and unsnap the wiper motor clip.

1. Push the clip away from the windshield wiper adapter and connecting arm clip until it clears the nib on the crack pin. Then, push the clip off the windshield wiper adapter and connecting arm clip.

1. Remove the windshield wiper adapter and connecting arm clip from windshield wiper motor crank pin.

1. Remove nut and ground strap.

1. Remove three attaching nuts from windshield wiper motor. Remove the windshield wiper motor .

Installation

1. Position the windshield wiper motor and install the three attaching screws. Tighten to 13.6-19.0 Nm (10-14 ft-lb).

1. Install nut and ground strap.

1. Connect wiper motor electrical connector.

1. Install clip completely onto right windshield wiper adapter and connecting arm clip. Make sure the clip is fully seated. Do not put the windshield wiper adapter and connecting arm clip on the motor crank pin and then try to install the clip.

1. Install the left windshield wiper adapter and connecting arm clip onto the wiper motor crank pin.

1. Install the right windshield wiper adapter and connecting arm clip onto the wiper motor crank pin. Pull the windshield wiper adapter and connecting arm clip onto the crank pin until it snaps into place. The clip is properly installed if the nib is protruding through the center of the clip.

1. Install the right windshield wiper mounting arm and pivot shaft and nut. Tighten the nut to 9.5-12.5 Nm (84-110 in-lb). NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 10 miles or more to relearn the strategy.
   

1. Connect the battery ground cable and turn the ignition switch on. Turn turn signal and windshield wiper switch off so windshield wiper motor will park, then turn ignition switch off. Replace right windshield wiper adapter and connecting arm clip access cover.

1. Install the windshield wiper mounting arm and pivot shaft and windshield wiper blade assemblies on the pivot shafts to dimension X. Dimension X is the distance between the centerline of the blade saddle and the top edge of the cowl top outer panel grille. The value of Dimension X for each vehicle is given in the Dimension X chart in the Specifications portion of this section.

1. Test the system.

Hello

The windshield wiper linkage comes as an assembly. The assembly comes with the two rotating splines that the wiper arms attach to. you must remove wiper arms. Remove cowl trim and remove bolts that hold the pivot points to the body. The new linkage that snaps to the wiper motor should come with a new retaining clip. You have to fish the linkage assembly through the access holes in the body by un bolting the wiper motor.

2002 Ford F-250 Windshield Wiper Motor Removal & Installation 1. Turn the ignition switch to the ON position. Turn the ignition switch ON until the wiper blades are straight up, then turn the ignition switch OFF. 2. Disconnect the negative battery cable. 3. Remove the right-hand and left-hand windshield wiper arm and blade assemblies. 4. Remove the cowl top vent panels. 5. Detach the electrical hardness connector at the windshield wiper motor assembly. 6. Remove 3 wiper motor (module assembly) retaining bolts and remove the module assembly from the vehicle. 7. Remove the wiper linkage retaining bolt and remove the linkage from the wiper motor. 8. Remove 3 retaining nuts and remove the windshield wiper motor To install; 9. Place the windshield wiper motor in position and install 3 retaining nuts. Tighten to 10-12 ft. lbs. (12-17 Nm). 10. Connect the wiper linkage to the windshield wiper motor and install the retaining bolt. Tighten the bolts to 14 ft. lbs. (20 Nm). 11. Place the wiper motor (module assembly) in position and install 3 retaining bolts. Tighten the bolts to 6 ft. lbs. (9Nm). 12. Install the electrical hardness connector to the windshield wiper motor. 13. Connect the negative battery cable. 14. Allow the windshield wiper motor to cycle several times while checking for proper wiper motor operation. 15. Turn the windshield wiper motor to the OFF position to park the wiper motor in the park position. 16. Install the cowl top vent panels. 17. Install the wiper arm and blade assemblies. Install the retaining nuts and tighten to 22-29 ft. lbs. (30-40 Nm). 18. Connect the negative battery cable. 19. Check the windshield wiper motor for proper operation and the wiper arms for adjustment.

Pivot Shafts and Linkage
The windshield wiper assembly is mounted below cowl top extension (021A36) . Linkages are connected with non-removable plastic ball joints. Windshield wiper mounting arm and pivot shafts are an integral part of the windshield wiper and are serviced as one unit. Removal

1. Disconnect the battery ground cable (14301). Refer to Section 14-01 .
   

1. Remove antenna mast from the antenna base.
   

1. Remove cap on LH and RH windshield wiper pivot arms to expose nuts retaining the arms to pivot shafts.
   

1. Remove two nuts, one from each of windshield wiper pivot arms . Lift wiper arms to service position, carefully rocking them back and forth to loosen them from the pivot shaft. Lift off windshield wiper pivot arms .
   

1. Remove seven screws retaining the cowl top vent panel.
   

1. Disconnect windshield washer hose (17A605) at LH side of vehicle just ahead of where it enters cowl top.
   

1. Remove hood cowl seal.
   

1. Carefully remove cowl top vent panel from vehicle.
   

1. Remove three retaining screws to cowl drain tube that is connected to top cowl.
   

1. Disconnect wiring harness leading to windshield wiper motor.
   

1. Remove five screws retaining cowl top to vehicle and remove cowl top and windshield wiper from vehicle.
   

1. Remove two screws and two nuts retaining windshield wiper to cowl top and separate the two parts.
   

1. Remove drive linkage from motor shaft linkage.
   

1. Remove remaining screws attaching windshield wiper and separate the two parts.
   

Item Part Number Description 1 02010 Cowl Top Panel 2 N621906-S2 Nut (2 Req'd) 3 17508 Windshield Wiper Motor 4 N805605-S36 Screw (2 Req'd) 5 17500 Windshield Wiper Assembly A — Tighten to 9-12 Nm (80-106 Lb-In)