Question about Ford Focus

1 Answer

MY DRIVERS DOOR AND MY FRONT PASSENGER DOORS WILL UNLOCK AND LOCK AND MY TAILGATE BUT NOT MY REAR PASSENGER DOORS MY NEARSIDE REAR DOOR WON'T EVEN OPEN MANUALY

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 4,388 Answers

Is the child safety lock on?

Posted on Sep 18, 2011

  • gerry bissi Sep 20, 2011

    If the child safety lock is not ON, and the door won't open from the inside or outside, then the latch must be bad. There is a linkage on each door handle, inside and outside. It is unlikely both fell off. You may have to pop the door trim apnel off to get your hand in there to oerate the latch manually. The outer part perimeter of the trim panel is held on with push pins. You pry out with a screwdriver close to each tree until it pops out. There may be one or two screws near the inside pull handle. Let us know how you are doing.
    The other possibility is that the lock actuator has the lock engaged, and the lock actuator is bad. In fact, that is more likely. Still have to remove trim panel for access.

×

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have 2007 chevy avalanche,..all the doors including the tailgate lock when I press the power locking button but when I press the unlock button only the front doors unlock but both rear doors as well as...


Depending on what you have for diagnostic knowledge and tools. You may want to send it in for diagnostics and repair. I can tell you that your vehicle's BCM (Body Control Module) controls these circuits. If it was a t my shop. I would first look for any fault codes. Then through the scan tool, manually command the doors to lock and unlock. Depending on what I find, take a closer look at the master control switch. This is in the drivers door and opens/closes windows and locks/unlocks doors. I'm forwarding you a couple wiring schematics just in case. I don't want to slow you down. FYI under the hood, inside the power distribution box. There is a relay for the tailgate lock/unlock. Any questions please feel free to write back. Good Luck.
2013-01-03_151104_ava-vedhudkhtg2d25qwad5sb33r-5-0.gif

2013-01-03_151140_ava2-vedhudkhtg2d25qwad5sb33r-5-2.gif

Sep 21, 2018 | Chevrolet Avalanche Cars & Trucks

1 Answer

2011 Ford Fiesta 5 speed manual base model no key fob ONLY drivers side door lock w key. Mechanism in drivers side door lock not catching not working will not lock or unlock. Electronics inside at console...


LOCKING AND UNLOCKING
You can use the power door lock control or the remote control to lock and unlock your doors and tailgate.See Tailgate Lock.
Power Door Locks
The power door lock control is on the driver and front passenger door panels.

AUnlock.
BLock. Remote Control
You can use the remote control at any time your vehicle is not running.
Unlocking the Vehicle (Two-Stage Unlock)
Press the button to unlock the driver door. Press the button again within three seconds to unlock all doors.The direction indicators flash. The direction indicators flash twice to confirm the change. The unlocking mode applies to the remote control, keyless entry keypad and intelligent access.
Press and hold both the lock and unlock buttons on the remote control for four seconds to disable or enable two-stage unlocking. Disabling two-stage unlocking allows your entire vehicle to unlock with one press of the button.
Intelligent access at the driver door unlocks your entire vehicle when you disable two-stage unlocking.
Locking the Vehicle
Press the button to lock all doors.The direction indicators flash.
Press the button again within three seconds to confirm that all the doors are closed.The doors lock again, the horn sounds and the direction indicators flash if all the doors are closed.
Mislock
If any door is open, or if the hood is open on vehicles with an anti-theft alarm or remote start, the horn sounds twice and the direction indicators do not flash.
Activating Intelligent Access
General Information
You can unlock and lock the vehicle without taking the keys out of your pocket or purse when your intelligent access key is within 3 ft (1 m) of your vehicle. Intelligent access uses a sensor on the back of the door handle for unlocking and a separate sensor on the face of each door handle for locking.
The system does not function if:
  • Your vehicle battery has no charge.
  • The key battery has no charge.
  • The key frequencies are jammed.
Note: The system may not function if the key is close to metal objects or electronic devices, for example keys or a cell phone.
Note: If the system does not function, use the key blade to lock and unlock your vehicle. See Remote Control.
Unlocking Using Intelligent Access
With your intelligent access key within 3 ft (1 m) of your vehicle, touch the unlock sensor on the back of the door handle for a brief period and then pull on the door handle to unlock, being careful to not touch the lock sensor at the same time or pulling the door handle too quickly. The intelligent access system requires a brief delay to authenticate your intelligent access key fob.
Locking Using Intelligent Access
With your intelligent access key within 3 ft (1 m) of your vehicle, touch the outer door handle lock sensor for approximately one second to lock, being careful to not touch the unlock sensor on the back of the door handle at the same time. After locking, you can immediately pull on the door handle to confirm locking occurred without inadvertently unlocking.
Note: Do not use the outside door handle as a roof cargo strap.
At the Electronic Tailgate (If Equipped)
Press the exterior tailgate release button inside of the tailgate handle. The tailgate unlocks and opens. See Electronic Tailgate.
Smart Unlock
This feature helps to prevent you from locking your intelligent access key inside your vehicle's passenger compartment or rear cargo area.
If you leave your key in the ignition, when you open the driver door and lock your vehicle with the power door lock control, the doors lock then unlock.
You can still lock your vehicle with the key in the ignition by:
  • Using the manual lock on the inside of the door.
  • Locking the driver door with a key.
  • Using the keyless entry keypad.
  • Using the lock button on the remote control.
Smart Unlocks for Intelligent Access Keys
This feature helps to prevent you from locking your intelligent access key inside your vehicle's passenger compartment or rear cargo area.
When you lock your vehicle using the power door lock control (with the door open, vehicle in park and ignition off), your vehicle searches for an intelligent access key in the passenger compartment after you close the door. If your vehicle finds a key, all of the doors immediately unlock.
In order to override the smart unlock feature and intentionally lock the intelligent access key inside your vehicle, you can lock your vehicle after all doors are closed by using the keyless entry keypad, pressing the lock button on another intelligent access key or touching the locking area on the handle with another intelligent access key in your hand.
When you open one of the front doors and lock your vehicle using the power door lock control, all doors lock then unlock if the ignition is on.
Autolock
Autolock locks all the doors when:
  • All doors are closed.
  • The ignition is on.
  • You shift into any gear putting your vehicle in motion.
  • Your vehicle reaches a speed greater than 12 mph (20 km/h).
Autolock repeats when:
  • You open then close any door while the ignition is on and your vehicle speed is 9 mph (15 km/h) or lower.
  • Your vehicle reaches a speed greater than 12 mph (20 km/h).
Autounlock
Autounlock unlocks all the doors when:
  • The ignition is on, all the doors are closed, and your vehicle has been moving at a speed greater than 12 mph (20 km/h).
  • Your vehicle comes to a stop and you switch the ignition off or to the accessory position.
  • You open the driver door within 10 minutes of switching the ignition off or to accessory.
Note: The doors do not autounlock if you electronically lock your vehicle after you switch the ignition off and before you open the driver door.
Enabling or Disabling Autounlock
You can enable or disable the autounlock feature in the information display or an authorized dealer can do it for you. See General Information.
Illuminated Entry
The interior lamps and select exterior lamps illuminate when you unlock the doors with the remote entry system.
The illuminated entry system turns off the lights if:
  • The ignition is on.
  • You press the remote control lock button.
  • After 25 seconds of illumination.
The dome lamp does not turn on if the control is set to the off position.
The lights do not turn off if:
  • You switch them on with the dimmer control.
  • Any door is open.
Battery Saver
The battery saver turns off the interior lamps 30 minutes after you switch off the ignition if a door is open and the dome lamp switch is on. It turns off the interior lamps after 10 minutes if the dome lamp switch is off.
Accessory Mode Battery Saver for Intelligent Access Keys (If Equipped)
If you leave the ignition on after leaving your vehicle, it turns off 15 minutes after you close all of the doors.

Mar 27, 2018 | Ford Cars & Trucks

3 Answers

Back tailgate lock won't open


Central lock problem, rear door and trunk don´t open - Xoutpost.com

www.xoutpost.com > ... > BMW SAV Forums > X5 (E53) Forum

Aug 23, 2014 - 10 posts - ‎4 authors
I have a problem on my X5, the remote key can only open the front ... I´m in a distante country without any BMW representative, but I can ... Remote keys can only lock andunlock the front doors, the rear door locks does not respond. .... the front doors openit won't unlock or lock the rear doors and rear trunk. Door Won't Lock With Key
10 posts
Sep 26, 2013
Door Lock (passenger side) won't unlock with remote
10 posts
Jan 10, 2011
Upper Tailgate wont open from the outside
8 posts
Sep 2, 2009
More results from www.xoutpost.com

X5 Tailgate Diagnosis E53 - YouTube

? 3:12
https://www.youtube.com/watch?v=ZqBfkJzUQug
Nov 7, 2011 - Uploaded by AskTheCarExperts
Lower tailgate diagnosis including relay location and fuse location. ... BMW 3 Series E90 Car Key Memory and ...

BMW Electric Boot Release Fix - YouTube

? 10:02
https://www.youtube.com/watch?v=snOVnM7hyO4
Jan 23, 2011 - Uploaded by Cpt MishMash VonRandom
Thanks**This is a quick walk through to repair the boot or trunk release button on y. ... or other BMW of the ...

BMW X5 xDrive 30i automatic tailgate does not w





Dec 14, 2015 | BMW X5 Series Cars & Trucks

1 Answer

Replaced door lock fuse on 03 Suburban, doors still won't unlock.


You need to replace the Unlock Relay, it should be in the fuse panel on the passanger side.

Dec 03, 2012 | 2003 Chevrolet Suburban

1 Answer

I have a 08 chevy avalanche the driver side front and rear door locks won't work when I use my keyless entry button or on the inside driver panel. Could it be a fuse? Passenger side works fine I try...


Do the power windows work ? DDM - driver door module fuse 15 amp - location is the instrument panel fuse box , plus LT DR circuit breaker 25 amp. Circuit breakers rarely go bad . The power locks are controlled by electronic's .The passenger side has another power supply ,that's why they still work .
Door Lock System Components
The power door lock system consists of the following components:
• The driver door switch (DDS)
• The passenger door switch (PDS)
• The body control module (BCM)
• The driver information center (DIC)
• The rear door lock/unlock relay (LBEC)
• The reversible door lock actuators in each of the doors and liftgate

The front power door lock switches are integral components of the driver door module (DDS) and passenger door module (PDS). The switches are 2 position normally open rocker switches. When placed in either the lock or unlock positions, the switches provide a direct input to the DDS or PDS. The DDS or PDS monitors these inputs and sends a LAN message indicating a change in the switch's respective position. Modules which activate the power door lock motors receive the LAN message and activate the motor in the appropriate direction to lock or unlock the vehicle's doors and liftgate. The rear door lock switch provides a lock and unlock signal to the body control module (BCM). The BCM upon receipt of a lock or unlock signal will control the rear door lock/unlock relay and also send a LAN message to the DDS and PDS to perform the appropriate function.
The modules which activate the power lock motors are:
• The DDS (driver door lock actuator)
• The PDS (passenger front door lock actuator)
• The BCM (both rear door lock actuators and cargo door/liftgate)
The DDS and PDS are directly connected to the respective door lock actuator through the door lock motor lock and unlock circuits. Once a door lock or unlock request has been received, the module will supply battery voltage to one side of the actuator and ground the other causing the doors to lock or unlock.
The rear passenger and endgate doors are controlled by the BCM through the rear door lock/unlock relay which is incorporated onto the printed circuit board in the LH BEC. The BCM controls the unlock relay by providing ground to energize the coil and controls the lock relay by providing battery voltage to energize the relay coil. The energized the relay and allows voltage to be applied to either the door lock motor lock or unlock circuits. Since the other side of the door lock actuator is connected to the normally closed contacts of the opposing relay to ground, the doors lock or unlock.

It's possible you have broken wire or wires inside the flex boot from the body of the vehicle to the driver's door . This happens a lot .
Fuse Block - I/P instrument panel
Left of the I/P behind the side trim panel

Mar 04, 2018 | 2008 Chevrolet Avalanche

1 Answer

2002 Jeep Grand Cherokee electric door locks not operatin


the passenger door switch pack controls all door locks as this is the receiver from the remote you might want to try this and also check connections

Jun 07, 2009 | 2004 Jeep Grand Cherokee

1 Answer

Power door locks won't unlock + tailgate won't open


your issue involves the master control switch panel on the drivers side and or the passenger side as well some how the contact inside the switch assembly has either shorted out or no longer makes contact for the unlock side of the circuit. replace the drivers side panel switchs it's either a series of switc hs or mostimes one sigle board of switchs. you are better off going to an auto parts store rather than a GM dealership this will save you quite a bit on cash on the parts. now as to the rear tailgate. if it is electronic controled and there is an issue with the master switch you can,t manually unlock it because of a safty issue built in the system. you can manually unlock the passenger compartment doors for thew same reasons of safety but doesn't apply to the tailgate. just replace the parts and this will take care of the problem

Apr 18, 2009 | 2004 Chevrolet Suburban

2 Answers

1999 Ford Explorer Door Locks


Unfortunately, This is a very common problem with Ford Explorers! Ford replaces the locks when it encounters this issue. I managed to unseize my passanger door and tailgate lock, but the drivers door lock is broken beyond repair. You can purchase new remotes for your explorer and program them very easily. Just google ford key fobs...

Jan 03, 2009 | 1999 Ford Explorer

1 Answer

2004 tahoe


make sure than you have not split any fluids on the passenger front door most of the times is where the module to control the windows and doors is located, try by unpluging the batterie and the after a minute plug it back and see what happend but if any of your ft doors have been split with liquid or rain has gone inside then most likelly the module got moisture and not working

May 31, 2008 | 2003 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

583 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...