I need the bolt torque specs

Here are the torque specs for the flywheel and clutch plate on a 2003 Kia Spectra: Flywheel: 78 - 80 ft-lbs (106 - 112 Nm) Clutch plate: 19 - 21 ft-lbs (26 - 29 Nm) It is important to follow the torque specs carefully when installing the flywheel and clutch plate, as over-tightening or under-tightening can cause damage. Here are the steps on how to torque the flywheel and clutch plate on a 2003 Kia Spectra: Install the flywheel and clutch plate. Use a torque wrench to tighten the flywheel bolts to 78 - 80 ft-lbs (106 - 112 Nm). Use a torque wrench to tighten the clutch plate bolts to 19 - 21 ft-lbs (26 - 29 Nm). Reconnect the battery and start the engine. Check for leaks. If you are not comfortable tightening the flywheel and clutch plate yourself, you can take your Spectra to a qualified mechanic.

With the clutch plate centre tool in position, tighten the clutch pressure plate bolts to 15 to 24 ft/lbs, (21 to 32Nm), tightening in a criss-cross pattern. I would suggest setting to 19 ft/lbs, (26Nm) as this is a mid range setting.

I have been working on cars for over 40 years and ASE certified and have never used torque specs on a pressure plate or Torque convertor I will put a breaker bar and socket on the harmonic balancer bolt on the front of the engine resting it up against the frame you should also use blue Loctite on pressure plate bolts then tighten them up in a star pattern be sure to have alignment tool in in place so the clutch disc is aligned in the center pressure plate the specs for tightening bolts are PFT

you will need a replica flywheel and new bolts plus torque range and manfacturers specs.

Torque Specification - National Truck Spares ' Parts

www.nationaltruckspares.com.au/Parts.aspx?ProductTypeID=8...

1073, 4BC2 tq, Isuzu, Torque Specification, KT26 TLD57 NKR57 NPR57 ... 1075, 4HF1Tq, Isuzu, Torque Specification, NKR66 NPR66, 92 - 03, 4HF1, 4334

Small Block Chevrolet V8 Engine Specs ' Torque Specs ...

boxwrench.net/specs/chevy_sb.htm

Flywheel (Clutch). Thread Locker, 60 ft-lbs. Clutch Pressure Plate, Thread Locker, 35 ft-lbs. Centerbolt. (Harmonic Damper). Engine Oil, 60 ft-lbs. Bellhousin

If you are replaceing clutch, there may be instructions. If you purchaced new clutch from autoparts store, they should be able to give you specs.

I'm replacing the clutch and the cover for the clutch and all I need help is with the torque lbs for every bolts for the clutch and the cover that goes on the clutch and all this is for a Kia Sportage 2000 4 x 4

Clutch disc and pressure plate. The bolts should be tightened in 2 or 3 steps, gradually and evenly. Final bolt torque is 14 ft. lbs. (19 Nm).

You need to get a manual. Try the Haynes manual for your car. Try autozone; generally available for around $20. This is not the type of thing that can be covered here in enought detail to do you any good.
Basics are;
disconect the negative battery cable, set parking brake
locate the trans mounting bolts
get something to support the engine and something to support the trans
seperate the trans from the motor by removing the bolts. On transverse mounted engines you will probably have to pull the trans to get enough room to remove the clutch and you'll probably have to remove the 1/2 shaft axles (front wheel cars) or drive shaft (rear wheel drive cars)
If replacing the entire clutc assembly (pressure plate, flywheel, and clutch), loosen the pressure plate mounting bolts gradually working your way around the pressure plate. If only replacing the clutch then seperate the sperate the pressure plate from the flywheel and remobe. Align clutch with a clutch allignment tools and replace pressure plate. Torque bolts to spec. reconnect the trans to the motor. Few other things to think about. You should replace the throwout bearng when doing a clutch. Lube the clutch fork as directed without getting lub on the clutch face. Hopefully I have convinced yu to get a manual or you will be hating life if you take this on without it.

Remove drive shaft,remove crossmember under transmission.Remove transmission and diconnect linkage.Remove bell housing,and clutch berring assembely.Remove bolts on pressure plate.Once this is done.Remove fly wheel for machineing.you will need a pilot shaft to alighn clutch assemblely.Possible one will come with new clutch and pressure plate.Reverse assemblely in same order remember to torque all your bolts with torque wrench.Take your time.