Need programming instructions for RKE for 2000 Mazda 626

everything will more than likely need to be reprogrammed at the same time. contact a local locksmith that does automotive work. lock smiths are much cheaper and do just as good a job.

You can purchase new Remote Keyless Entry (RKE) transmitters from the dealer or you can order them online at the web sites listed below or several others. Your vehicle provides for programming the RKE transmitters without the use of a scan tool. Follow the instructions below.

2000 PONTIAC GRAND AM RKE TRANSMITTER PROGRAMMING

WITHOUT A SCAN TOOL

1. Close all vehicle doors. Remove key from ignition lock cylinder

NOTE: STEPS 2 AND 3 MUST BE COMPLETED WITHIN 25 SECONDS OF PRESSING THE DOOR UNLOCK SWITCH
2. Press and hold door UNLOCK switch. While holding UNLOCK switch, insert and remove the key in the ignition lock cylinder twice. Do not rotate the lock cylinder.
3. Insert the key a third time, leaving the key in the lock cylinder. Keep the lock cylinder in the LOCK position for the remainder of the procedure. Release the door UNLOCK switch. The chime will sound 3 times to signal that the programming/diagnostic mode is active.
4. Press and hold LOCK and UNLOCK at the same time on the RKE transmitter for approximately 4 seconds. The chime will sound 2 times signaling that the transmitter has been programmed.
5. Repeat step 4 for each transmitter being programmed. (You can program up to 4 transmitters.)

6. To exit program mode, turn the key to the RUN position then back to the LOCK position and remove the key. Your transmitters should now work to lock and unlock your doors.

2000 Pontiac Grand Am Transponder (direct links)

- autotransponder.com

-keylessremotes.com

-ikeyless.com

The spare key is the valet key, You can call the dealer and have them cut you new keys for you car. You will need the VIN number and your registration for the car. If it doesn't have chip in it, they can make it for you in a couple of minutes. If it has the chip in it, they will have to order it. Without the chip, the key will cost between $20 and $30 dollars.

Go to online store reliable they have repair manuals I am sure you will get the solution. Here's the link
MAZDA 626 SERVICE REPAIR MANUAL 1997 1998 1999 2000 2001 2002 DOWNLOAD

Click on the following free, direct Link. It has all the Timing Belt Diagrams you will need, complete with Instructional and Directional Diagrams to set your Timing.

Let me know if this helped or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/2000/make/mazda/model/626/2000_mazda_626_timing_belt_diagram_marks.htm

1. Remove key from ignition.
2. Close all doors.
3. Open driver side door and leave open.
4. Insert key in ignition, Turn key to ON (as far as you can go without starting the engine) and OFF, Remove Key.
5. Repeat step 4 two more times, making sure you remove key each time.
6. Close and then open the driver’s door three times.
7. Buzz sound or chime should be heard at this point signaling that the vehicle is now in programming mode. If not,
wait 40 seconds and return to step 1.
8. All transmitters need to be programmed at this time, including the old ones. Push any button on a transmitter two
times. A buzz sound to chime should be heard at this point signaling that the vehicle has accepted the new
transmitter code. Repeat for next transmitter, up to a total of three remotes (including any old remotes).
9. After all remotes are programmed, wait 15 seconds or until you hear four chimes signaling successful
programming.

Good luck and this should work.

To program your vehicle's key fob you will need a scan tool. Select PROGRAM RKE on the scan tool and follow the instructions on the scan tool screen.

I had a similar problem with a second-hand Mazda2, was intermittent too so the seller kept telling me it was OK. Eventually turned out to be a loose connection with the fob, I bought another off eBay and billed the garage for it, found instructions for programming it online and it's worked ever since.

There is a way to program a remote if there is already a valid remote. Unfortunatly if you don't have a valid remote the only way to get one programmed is at the dealership with their scan tool.

I have pasted directions for programming a remote if there is already a valid transmiter.


CUSTOMER PROGRAMMING For a customer to be able to program RKE transmitters themselves, at least one RKE transmitter must be programmed already. This procedure is to add additional transmitters. If all transmitters are lost, the DRB III® scan tool must be used to program the new transmitters.

1. Insert the key into the ignition switch, and turn the ignition switch to the RUN position without starting the vehicle (allow chimes to stop).
2. Using the RKE transmitter programmed to the RKE module, press and continuously hold down the UNLOCK button for 4-10 seconds.
3. Within the 4-10 second time range, continue to hold the UNLOCK button and press the PANIC button. Both buttons may then be released. Upon the PANIC button being depressed, the message for customer programming mode will be transmitted to the RKE module.
4. A chime will be heard to verify that the customer programming mode has been entered (allow 3 seconds to hear chimes).
5. Press and release any button on each transmitter that is to be programmed to the RKE module, including any transmitters which were previously programmed to the RKE module (with a maximum of four possible). After each transmitter is successfully programmed, a chime will be heard to verify that successful programming of the transmitter has occurred.
6. After thirty seconds, or upon the ignition switch being turned OFF, the RKE module will exit programming mode.