I had the exact same issue with my 2007 Yaris. I took the radio out and checked all the connections- (all Good) then traced the wires through out untill I reached the trunk. I had a bunch of stuff in the trunk that had some how hit the speaker connections and bent the connections on one of the speakers. I removed all the stuff from the trunk and re-solder the connections. After that the speakers kicked back on for the entire car. Check the trunk - if you have it loaded with junk like I did, this may be the cause of your speaker failure. Good Luck!
Question edited for a lot more clarity.
Question moved to model category.
Could the wobbling pulley have destroyed the crankshaft position sensor? You need a good auto electrician.
It the other light in the cluster work, then the grounds are fine. Grounds are normally next to the light cluster screwed to a bracket on the chassis.
https://www.startmycar.com/ca/toyota/yaris/info/fusebox/2007
Fuse 35 covers them, but also covers other important things like the electric power steering. DRL are also a function of the Body Control Module. You need an Auto Electrician with a pro grade scan tool computer.
35
(ECU-IG) Daytime running light system, anti-lock brake system, electric power steering system, power windows, door lock system, theft deterrent system, electric cooling fan
If your keyless entry remote has never worked it either needs to be programmed to the vehicle or it is the incorrect remote part number for they vehicle. First step is to call your local dealership, ask for service, then verify your vehicle came equipped with the keyless entry option and verify the key fob part number. When calling the dealer have your vin# handy, they will need that. Once you have verified your vehicle has keyless entry option and you have the correct keyless entry remote part number then find a locksmith to program the remote to your vehicle. We suggest a locksmith because they are usually more affordable than the dealer and they come to you.
If your keyless entry remote has worked before and it just stopped working, here are a few tips to try to get it working again:
1) Change the battery
Batteries don't last forever, you'll be surprised how often it's just a dead battery! Search our YouTube channel on how to change a key fob battery for your specific year, make, and model!
2) Wipe the board
The board inside your remote can get a lot more filthy than you think! When the board is dirty it can prohibit the contact to the circuit board when you push down on the button. Simply wiping the circuit board off can make your key fob like new again!
3) Get it checked
Go to your local hardware store like AutoZone or Oreilly's. They usually have a RF frequency tester. This little gadget will let you know if your key fob is sending a signal. If it is, you may need to reprogram your key fob to your vehicle
4) The old car battery reset trick
I know this sounds absurd, but it works sometimes and is worth trying. If you exhausted all of the options above, disconnect both terminals on your car battery for 10 minutes. Then reconnect them and try your key fob. This has worked for many people and I have no idea why. If you do, please comment below to explain.
5) New fob!
It might be time for a new key fob! No need to dread over the expensive costs of a new key fob, at Keyless Entry Remote Fob Inc., you can get a refurbished one for a very affordable price! You won't even be able to tell the difference. Just search your vehicle make, model, and year to purchase a key fob or give us a call at 402-671-5100.
I reckon it can only be three things;
The door switch because it signals that the door is open. Does the interior light come on when you open the door?
The microswitch in the ignition lock that identifies there is a key in the lock.
Or it needs reprogramming by the dealership.
Mr.Shehandj, I juste read your question.
My Advice,if you have mechanical knowledge,just go by the air filter cover and on the one part of the cover which is tightened to the throttle body of your engine there is a small electronic sensor called Air Mass Sensor withe a wiring connector plug. Just unplugged it, remove the two little screws pull it out carefully and remove the "O " ring rubber seal. By using a carburrettor Cleaner (Master USA Carb Cleaner ) for me is the No1, spray into the hole where where you can see two little elements called hot wire. Surely there is a dust dirt covering them. Bu spray in you will remove the dirt. Is not themassive use of carb cleaner does the job,is the correct cleaning. Please!! Do not bang the sensor or hit it at all. Just let it dry by the air. Put the "O" ring rub sealer and screw everything back and connect it. Air filter properly back and give it a try. Best of Luck.
on either side of the boot interior, there are what look like air vents. these clip out from the top (with a flat screwdriver) you then unbolt the light unit, pull it out. the bulb holder then unclips easily.
First you must remove the plastic cover from on top of the engine to access the ignition coils. The next step is to remove the ignition coils. To do this you must carefully disconnect the plug by holding down the plastic tab while pulling the plug off the coil. Then you must remove the small bolts holding the coils to the valve cover. Pull the coils straight out. To remove the spark plugs you will need a torque wrench, long extension and a self holding spark plug socket. All these can be bought at your local auto parts store. The spark plugs are removed by unscrewing them from the cylinder head and pulling them straight out. Installation is the reverse of removal. The spark plugs are tightened to 25 foot pounds of torque and the small bolts for the ignition coils are tightened to 10 foot pounds of torque.
as a toyota technician, its probably the wrong fitted of the ring, once you replace the bearing they will removed the ring and in that ring there is a small hole that the sensor goes in. speedometer will not work not work if there is a malfunction in abs and it is speedometer,brake warning light are integrated with abs ecu.
get IT test from toyota motors@Rs 1000/-.Tey will tell u any one or both rear sensors faulty.Get the sensor along with hub from bilalganj lahore@Rs 4000/ and get it changed from mechanic.Any problem contact me at email [email protected]