20 Most Recent 2006 Lincoln Town Car - Page 6 Questions & Answers

The fan (blower motor) is located on the passengerside under the dash in heater box, remove and make sure there no trash or leaves hitting the plastic fan wheel.replmove bolts holding motor to heaterbox and then remove the fan motor.

35 years as a Ford tech and never heard of this, i get all the TSB's

there may be a few things causing this, first make sure there no open holes in floor, then check trunk seal and make sure its not coming from trunk, next would be the back window,take a water hose and spray diffrent areas and check for leaks inside,could be also rubber around the back door or rust holes in wheel wells of rear wheels,

advised to get a good panel beater

Here is the method for the 2004 model. I think the 2006 is the same.

Turn the ignition to the "ON" position. Press "SETUP" button. "PRESS RESET FOR SYSTEM CHECK" is displayed. Press "RESET" button.
"OIL LIFE % HOLD RESET NEW" is displayed. Press and hold "RESET" button until "IF NEW OIL HOLD RESET" is displayed. Press and hold
"RESET" button until "OIL LIFE RESET TO 100%" is displayed.

check the exit of the air conditioner. maybe is blocked. and instead of taking the sweet out of the car, is dripping inside. that is easy to do, and the exit of the air conditioner is usually visible on the engine side of the panel.

there is another bulb that is not working right.

open your hood locate the back of the light that you want to replace these are usually held in place by self locks turn the light counterclockwise until it unlocks pull it out of the opening be sure that you dont touch the tip of the new bulb with your finger or hand or youll blow it as soon as you turn it on (the oils in your skin) put the new one in and reverse the process to install.

acc or cigar

Check for stains in the valve cover gasket on the side of the oil filter, and in the engine block right above the filter. There is not much that can leak on that side, other than filter itself, and you already checked it. You HAVE to take the car to dealer for warranty inpection, and repair. The issue not only has to be covered by warranty, but by not doing so in time, it might void the warranty, for being careless about it.

The compressor will only inflate once or twice and only within a half hour of the ignition being turned off. If the bags deflate over night there is a leak in the bag and will probably need to be replaced. If you get under the car and take a look at them you will likely see deep cracks in them, specifically around where they fold.

how do i program a garage door opener on a 06 mercury mountaineer

u cant- should have air bag system check out by dealer or trained mech system can activate and cause serious injury

you may want to check the temperture sensor

check the obvious first, water level, check the fan is switching on at temp, by removing the wires for the thermo switch,( a large brass "nut" with 2 wires attatched, on either the thermostat housing or the radiator) and connecting them together with the ignition on. If the fan kicks in then you know the fan and other electics is ok. To replace the switch, simply unscrew and replace with a new one.They are quite cheap to buy.
If the fan doesn't kick in the check the fuse, wiring for loose wires/connections/breaks. check the relay and if it has a fuse on check that also.

You should fix it.

should tell you how to reset that in your hand book that came with the car

First thing to look for is a bulb that's not working. Most cars use this feature to let you know when a light is not working. Try this: While the left flasher is going fast, check to make sure ALL the lights are working as there may be more than two. Use the right signal as a reference to check how many there are that SHOULD be working.

If this problem comes and goes, there is most likely a bad connection between bulb and socket and if so, unplugging/replugging the bulb should fix it. There are two bulb types: push-in and push-twist-pull.

Feedback always welcome, and don't forget to vote!

1] Press the SETUP button to display PRESS SELECT TO BEGIN SYS. CHECK.
2] press the SELECT BUTTON to display OIL LIFE---PRESS RESET IF NEW OIL
3] press and hold the RESET button to displayOIL LIFE START VALUE SET TO XXX% is displayed. The oil life is now set to 100%