2005 Jeep Wrangler - Answered Questions & Fixed issues

Thank you for taking the time to respond.

2005 Jeep... | Answered on May 02, 2019 | 196 views

You will get your solution and all info on service info, repair info, parts info, wiring/electrical/fuse diagrams, error/fault codes, torque specs, PCV,
owner's/service/repair/parts/maintenance manuals etc everything
this website www.reliable-store.com
it's a very good website for vehicle problems even as old as 1991 ford..

2005 Jeep... | Answered on Mar 19, 2018 | 395 views

Blower resistor is bad . Do you know what that is ?
Jeep Cherokee Blower Motor Resistor Replacement

2005 Jeep... | Answered on Nov 17, 2017 | 436 views

Have you checked the clutch master cylinder fluid level?

2005 Jeep... | Answered on Apr 04, 2017 | 377 views

its bad,the PDC
no country stated, no engine stated,? why?
the 2005 (answering for USA)
PDC hard short all fuses, all breakers all relay out
means what?
well power distribution2 below shows all that, every wire there.
ASD relay pulled? you never said relays, they can (weld closed inside contacts can)) and is unfused, this relay. fact
i read the 22 pages for you there,
its just fuses and relays, no magic until 2007 (TIPM electronics)
this car is easy fix,. due to 2005 year.

looking now , TJ unlimited it is.
see the manual yet, see how this all works 2003 to 2006 year.
chapter 8w shows wiring, and modules the rules.

8w, pdc 2, chapter see that here, its there, clear as day.'


2005 Jeep... | Answered on Mar 30, 2017 | 87 views

to check

maf or 02 sensors
plugs ,coil, timing
fuel delivery to injectors

2005 Jeep... | Answered on Mar 08, 2017 | 199 views


did you read manual yet.
open glove box, read pages in oper, guide on top yet>

2005 Jeep... | Answered on Jan 03, 2017 | 33 views

I have an 05 6 cylinder automatic TJ. The other morning I was getting trouble codes U0101 and P1603. For a few seconds the Jeep was shaking and for the entire 30min ride it wouldn't shift into the last gear, it would just continue to rev. The next day I drove it and it was fine. I also noticed a slight high pitch whine noise coming from the engine at low speeds. Any suggestions? Thanks!

2005 Jeep... | Answered on Dec 03, 2015 | 1,072 views

check adjustment on shifter arms under on transfercase

2005 Jeep... | Answered on Aug 07, 2015 | 115 views

Ask parts store to run the codes (usually for free).

2005 Jeep... | Answered on May 04, 2015 | 72 views

disconnect battery for ten min

2005 Jeep... | Answered on Apr 03, 2015 | 121 views

pull out spark plugs and see if they all look the same,could be dirty fuel injectors or a blocked fuel filter

2005 Jeep... | Answered on Apr 03, 2015 | 148 views

Sounds like the synchro mesh has worn out

2005 Jeep... | Answered on Apr 03, 2015 | 37 views

so its just the light bothering you, (i ignore mine) I can tell car is in 4wd or not, dont need no stinkn light, so....
is it in 4wd or not? we cant guess that. only you..
the light is hard wired to the transfer case switch
if the switch closes, you are in 4wd, or the switch is bad. end story on silly light. and fuse 10 is the power for that light.
on this car , there is no computer running this light,

im driving on what.? dirt, ice, dry pavement what?

my guess, wild. is car is in 4wd. and you are not on ice or dirt and its stuck, Part time 4wd is for dirt or ice only and will stick.

drive to dirt, or jack up 1 wheel
and shift in to 2H.
fixed now?
light out?

answering for PT 4wd . not
came new with NV231 or 241 and both are part time 4wd, now AWD.

ever read this.


dont do that, posted 100s of time here.

2005 Jeep... | Answered on Mar 17, 2015 | 244 views

Did you replace the O2 sensor after the catalytic converter? This code is set by the rear O2 sensor. It usually indicates early failure or restricted catalytic converter. May want to have an exhaust back pressure test performed.

2005 Jeep... | Answered on Mar 03, 2015 | 687 views

Clutch switch keeps it from cranking.
You can bypass the cluctch switch. Make double sure transmission is in neutral. On many jeeps, under the hood is fuse/relay box. One of the relays is the starter motor. Pull the relay. With a pair of pliers, take a paper clip and short the pins that go to starter. They wire can get hot. If the starter cranks, you might be right (see ignition switch and any interlocks - like clutch switch), if the starter doesn't crank, get a new starter.

2005 Jeep... | Answered on Feb 16, 2015 | 164 views

2095 ( a jeep factory code that is , jeep only)
reset. like all cars , you can reset any code, with any scan tool
but if the failure is real and present it will NOT.
that is its purpose to report real failures.
is this the 3.8Liter v6 , like mine is?
down means not the front sensor.
engine >>>>Up >>>>CAT >>>> down?>>>>> tail pipe end.
this is an air leak (crack) behind the cat converter
or the sensor is bad, (down stream.)
or wires fell off, (common) LOOK FIRST.see damage there?

2005 Jeep... | Answered on Feb 16, 2015 | 291 views

If the Clutch switch is bad it wont let it turn over at all.

2005 Jeep... | Answered on Sep 28, 2014 | 250 views

Could be starter soilinoid

If you need further help, reach me via phone at https://www.6ya.com/expert/scott_87482045335a4757

2005 Jeep... | Answered on Sep 06, 2014 | 155 views

Likely that the "clicking sound" behind the dashboard is the IGNITION RELAY. Start by replacing the ignition relay (inexpensive and easy to replace).

2005 Jeep... | Answered on Sep 06, 2014 | 221 views

Not finding what you are looking for?
2005 Jeep Wrangler Logo

342 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Jeep Experts


Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides