20 Most Recent 2005 Jeep Wrangler - Page 8 Questions & Answers


when you say you had a defective rotor turned do you mean it was skimmed due to warping.if so, skimming is not any good for a warped rotor, replace both sides with new asap,or the vibration will cause bushes to fail at worst.
warped rotors are the bain of all modern cars as makers dont use ventilated types (too expensive)

2005 Jeep... | Answered on Aug 18, 2010


Hi. Issue could not be your AC. check the cooling system of your Jeep. Try putting a coolant first and observe. If same thing happens check the water pump. it might not running perfectly that causes the water not to circulate properly.

2005 Jeep... | Answered on Aug 12, 2010


You'l need to assign each dumper with a work order with specifics of procedures done each day to the vehicle, and expected maintenance for each day. Each vehicle will obviously have an assigned number to track and a worko procedure for each task and by whom. You can make a list in Excel for easy tracking.

2005 Jeep... | Answered on Aug 02, 2010


Check and/or replace the power motor power module located oon the blower housing.




5ba5a0f.gif

2005 Jeep... | Answered on Jul 21, 2010


Unscrew the old one and screw in the new one (make sure it has antiseize on threads. I think its 21 or 22mm. The light won't go out till you run it through a complete drive cycle (about 20 miles. Or you can clear the code with a scan tool.

2005 Jeep... | Answered on Jun 27, 2010


hello there:
you may need too cycle the on and off several time giving it about twenty seconds in between the cycles this should re-prime the fuel system listen for the fuel pump to stop pumping before cycling the key on and off this should solve the problem hope this helps you out thanks

2005 Jeep... | Answered on May 30, 2010


nothing serious just check the bulbs

2005 Jeep... | Answered on May 04, 2010


A p0057 code is related to the heater circuit voltage for the bank 2 sensor 2 Oxygen sensor. The PCM (computer) controls a heating element inside the O2 sensor that helps the sensor reach a high temp in order for the O2 to start working faster. It seems this circuit is not working, therefor the PCM alerts us by displaying a trouble code. In most cases, replacing the O2 repairs this code.

2005 Jeep... | Answered on May 04, 2010


The resistor pack is located behind the glove box. With the glove box out look to the bottom right there will be several harnesses down there, the one you are looking for is held in by 2 bolts (8mm i believe). Remove those two bolts, it will be tricky (there's not a lot of wiggle room). once removed slide the harness out and unplug the resistor pack. I found it helps to remove the harnesses close to the resistor to give yourself more room.

2005 Jeep... | Answered on Apr 24, 2010


I also say its a vacuum issue. Any vac leaks on the engine?

2005 Jeep... | Answered on Apr 23, 2010


be sure that you have indeed taken all the bolts out. There should be one way in the back as well. If you are absolutly sure they are all out then take a flat head screw driver or a chisel and along where the gasket would be gently set the point end of the tool you use on that gasket and tap with your palm or a hammer. The gaskets dry to the surface and it takes a bit to break it free. Let me know what happens. Don't worry about the gasket as you will need to replace it when the cover is off any way. The Raz

2005 Jeep... | Answered on Apr 17, 2010


HO2S Heater Control Circuit Low (Bank 2 Sensor 2)

2005 Jeep... | Answered on Apr 07, 2010


more Than Likely it Need's An Alignment.could be bad tires or a bent rim.

2005 Jeep... | Answered on Mar 31, 2010


get it jumped off or charge the battery

2005 Jeep... | Answered on Mar 28, 2010


Once you take the caliper bracket off, the rotor should just fall off. If the Jeep stops without any vibrations I would leave the rotors alone., unless they are scored badly from brake pads worn out and metal to metal.

2005 Jeep... | Answered on Mar 19, 2010


Disconnect battery, remove starter bolts and wiring from starter, remove starter, reverse for reinstall.

2005 Jeep... | Answered on Mar 17, 2010

Not finding what you are looking for?
2005 Jeep Wrangler Logo

342 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Wrangler Jeep

  • Wrangler Jeep

Most Popular Question

gear slip when putting into first third

  • Cars & Trucks
Loading...