20 Most Recent
2003 Cadillac Escalade Questions & Answers
Vehicle experiencing front end 'shimmy' at all
You need to have the front end checked out at an alignment shop. Possible causes are worn tire rod ends or control arm bushings, failing drive axle CV joint, loose stabilizer bar, etc.
Service Stability, ABS and Traction control light will come on if i go over a hill and stay on. i know it's all connected. can it be fixed? i read on internet on another blog that GMC told a clien
Having a qualified repair shop check it out would be your best bet . These light;s being on means DTC'S - dignostic trouble codes are stored .
SERVICE STABILITY SYSTEM
Refer to ABS Description and Operation in Antilock Brake Systems
Vehicles with RPO JL4 are equipped with an EBC 430EV ABS/DRP/TCS/VSES module.
This module provides the following vehicle performance enhancement systems.
• Antilock Brake System (ABS)
• Dynamic Rear Proportioning (DRP)
• Traction Control System (TCS)
• Vehicle Stability Enhancement System (VSES)
The following components are involved in the operation of the above systems.
• Electronic brake control module (EBCM) - The EBCM controls the system functions and detects failures.
The EBCM contains the following components.
- System relay - The system relay is internal to the EBCM. The system relay is energized when the ignition is ON. The system relay supplies battery positive voltage to the valve solenoids and to the ABS pump motor. This voltage is referred to as system voltage.
- Solenoids - The solenoids are commanded ON and OFF by the EBCM to operate the appropriate valves in the brake pressure modulator valve (BPMV).
- Longitudinal Accelerometer - The EBCM uses the longitudinal accelerometer to determine the actual straight-line acceleration of the vehicle.
• Brake pressure modulator valve (BPMV) - The BPMV uses a 4-circuit configuration to control hydraulic pressure to each wheel independently.
The BPMV contains the following components.
- ABS pump motor and pump
- Four isolation valves
- Four dump valves
- Two TC isolation valves
- Two TC supply valves
- A master cylinder pressure sensor
- A front low-pressure accumulator
- A rear low-pressure accumulator
• Wheel speed sensors (WSS) - As the wheels spin, toothed rings interrupt magnetic fields in the wheel speed sensors. This causes each wheel speed sensor to generate an AC signal. The EBCM uses these AC signals to calculate the wheel speed. Any imperfections in the toothed ring, such as a missing or damaged tooth, can cause an inaccurate WSS signal.
• Traction control switch - VSES and the engine torque reduction function of TCS are manually disabled or enabled by pressing the traction control switch.
• Lateral accelerometer - The EBCM uses the lateral accelerometer to determine the sideways acceleration of the vehicle. The lateral accelerometer is packaged with the yaw rate sensor as a single component.
• Master cylinder pressure sensor - The master cylinder pressure sensor is located within the BPMV. The master cylinder pressure sensor uses a 5-volt reference and generates an output signal proportionate to the hydraulic fluid pressure which is present in the front brake circuit at the master cylinder.
• Yaw rate sensor - The EBCM uses the yaw rate sensor to determine the rate of rotation along the vehicle's vertical axis. The yaw rate sensor is packaged with the lateral accelerometer as a single component.
• Steering wheel position sensor - The electronic brake control module (EBCM) receives several inputs from the steering wheel position sensor. 3 digital square wave signal inputs are wired directly to the EBCM harness connector, however, only signals A and B are used or monitored. The failure of the index pulse signal does not effect VSES function. The body control module (BCM), which receives an analog steering position sensor input, transmits steering position data on the serial data line. The EBCM monitors the serial data information as an added failsafe for the steering position sensor circuitry. Battery voltage is supplied to the digital portion of the steering wheel position sensor from the cruise control fuse. The analog portion of the steering wheel position sensor is supplied a 5-volt reference from the BCM. This circuit is also used for a lamp dimming function.
• Precharge pump motor and pump - The precharge pump assembly is used to assist the ABS pump in rapidly building hydraulic pressure needed during certain TCS or VSES events
Do you know what DTC'S are ? The ABS , traction control can set a bunch .
DTC C0035 or C0040
DTC C0045 or C0050
DTC C0110
DTC C0131
DTC C0161
DTC C0186
DTC C0196
DTC C0201
DTC C0220
DTC C0221-C0227 or C021 (W/O JL4)
DTC C0221-C0227 or C021 (W/JL4)
DTC C0228
DTC C0229 or C029 (W/O JL4)
DTC C0229 or C029 (W/JL4)
DTC C0235-C0237 or P0609
DTC C0238 or C038
DTC C0240
DTC C0241-C0243
DTC C0244 (W/O JL4)
DTC C0244 (W/JL4)
DTC C0245 (W/JL4)
DTC C0245 (W/O JL4)
DTC C0246-C0254
DTC C0265 or C0266 and C065 or C066
DTC C0267 or C0268 and C067 or C068
DTC C0269 or C0274 and C069 or C074
DTC C0271-C0273, C0284
DTC C0279 (W/O JL4)
DTC C0279 (W/JL4)
DTC C0281 or C081
DTC C0283 (W/O JL4)
DTC C0283 (W/JL4)
DTC C0287, P1644, or P1689
DTC C0290 or C0292 (W/O JL4)
DTC C0290 or C0292 (W/JL4)
DTC C0291
DTC C0297
DTC C0298 or P1571
DTC C0455
DTC C0472 or C0473
DTC C0550
DTC C0558
I want to rebuild my transmission for a 2003
Automatic transmission rebuilding on newer cars is an astronomical undertaking. Tons of special tools. One minor mistake and you have to do it all over again.
Buy a GM reman that's been tested on a stand and has a 3yr/50,000 mile warranty that is honored nationwide at any GM dealer.
Just keep your paperwork.
The front seats for our 2003 Escalade will not move forward or backward and the heat control for the front seats will not work.
Does your Escalade have memory seats ?
There are 2 options of power seat systems available in full size trucks. The 6 way driver and passenger power seats, and 8 way driver and passenger power seats with driver memory. For the driver memory seat operation refer to
Memory Seats Description and Operation . Power seats without memory are completely controlled through the power seat switch. Battery voltage is supplied to the power seat switch through the power seat circuit breaker. While the seat adjuster switches are in an inactive state the switch contacts are closed to the power seat switch ground circuit. When a power seat switch is pressed to an active state the switch contact is closed to the battery voltage supply circuit. Each seat adjuster motor is controlled by the power seat switch through 2 motor control circuits. The seat adjuster motors are bidirectional and the direction of adjuster motor rotation is determined by which of the adjuster motor control circuits is switched to battery voltage while the other remains grounded.
Not finding what you are looking for?