20 Most Recent 2006 Mercury Milan Questions & Answers

0helpful
1answer

Where is transmission filter located on 2006 mercury milan

INSIDE THE TRANNY
8/26/2021 7:36:21 AM • 2006 Mercury... • Answered on Aug 26, 2021
0helpful
1answer

Does 2006 mercury milan have aux capability in the back of the radio?

Despite your car having an AUX button, you will be disappointed to know this menu is not operational as there is no AUX jack.
4/29/2020 12:02:14 AM • 2006 Mercury... • Answered on Apr 29, 2020
0helpful
1answer

Milan fuel pump relay location

I got a question Does Anyone know were the fuel relay switch is on a 2011 Mercury Milan

11/26/2019 8:24:25 PM • 2006 Mercury... • Answered on Nov 26, 2019
0helpful
3answers

2006 Mercury Milan key stuck in ignition.

There's a TSB published by ford for this condition. It's caused by a binding shifter button.


adobe.gif Printable View (73 KB) TSB
07-14-7
  • KEY STUCK IN IGNITION / SHIFTER BINDING CONDITION
Publication Date: July 6, 2007
FORD: 2006-2007 Fusion LINCOLN: 2006 Zephyr MERCURY: 2006-2007 Milan
This article supersedes TSB 07-2-1 to update the Part List. ISSUE: Some 2006-2007 Fusion, Milan and 2006 Zephyr vehicles built before 9/4/2006 may exhibit a customer concern of the ignition key getting trapped or a shifter slider binding condition. Most of the key trapped conditions are caused due to a binding shifter button which does not allow the pawl to contact the park detect switch.
ACTION: Follow the Service Procedure steps to correct the condition.
SERVICE PROCEDURE If the key will not release from the ignition cylinder lock follow the Key Trapped procedure. On vehicles with a hard-to-shift shift lever into park or slider bunching/binding then follow the Shifter Slider Binding procedure. Key Trapped:
  1. Actuate knob button 5-10 times, observe for binding or sticky condition.
  2. Replace knob assembly if the knob sticks following Workshop Manual (WSM), Section 307-05. NOTE: WHEN REPLACING THE SHIFT KNOB DO NOT REUSE THE SCREWS. REMOVE AND DISCARD THE SCREWS. INSTALL TWO NEW SCREWS AND TIGHTEN TO 18 LB-IN (2 N-m). DO NOT OVER TIGHTEN THE SCREWS OR DAMAGE MAY OCCUR.
Shifter Slider Binding:
  1. If shifter slider is bunched up or binding, replace bezel assembly following WSM, Section 307-05. NOTE: WHEN REPLACING THE BEZEL, CARE NEEDS TO BE TAKEN TO ENSURE THAT THE BRAKE SHIFT INTERLOCK OVERRIDE TAB IS PROPERLY ALIGNED INTO ITS GUIDE. REFER TO FIGURE 1.

    tb8706a.gif
    Figure 1 - Article 07-14-7

    NOTE: WHEN REINSTALLING THE SHIFT KNOB DO NOT REUSE THE SCREWS. REMOVE AND DISCARD THE SCREWS. INSTALL TWO NEW SCREWS AND TIGHTEN TO 18 LB-IN (2 N-m). DO NOT OVER TIGHTEN THE SCREWS OR DAMAGE MAY OCCUR. NOTE: IF OVERRIDE CAP IS DAMAGED DURING REPAIR, IT IS AVAILABLE SEPARATELY.

PART NUMBER PART NAME 6E5Z-7D443-B Bezel Asy-Black w/FNR5 Trans (Fusion-Milan) 6E5Z-7D443-C Bezel Asy-Black w/Aisin F21 Trans (Fusion-Milan) 6H6Z-7D443-A Bezel Asy-Satin Nickel (Zephyr) 6E5Z-7213-C Knob Asy-Black (Fusion-Milan) 6H6Z-7213-A Knob Asy-Charcoal (Zephyr) 6H6Z-7213-B Knob Asy-Charcoal-OD (Zephyr) 6E5Z-7A214-B Override Cap-Black (Fusion-Milan) 6H6Z-7A214-A Override Cap-Satin Nickel (Zephyr) W790088-S901 Screw (2 Req)
WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage
IMPORTANT: Warranty coverage limits/policies are not altered by a TSB. Warranty coverage limits are determined by the identified causal part.
OPERATION DESCRIPTION TIME 071407A 2006-2007 Fusion, Milan And 2006 Zephyr: Replace Knob Assembly, Includes Time To Diagnose And Verify Repair (Do Not Use With 04536A, 04536B, 7213A) 0.3 Hr. 071407B 2006-2007 Fusion, Milan and 2006 Zephyr: Replace Bezel Assembly Includes Time To Diagnose And Verify Repair (Do Not Use With 04536A, 04536B, 7213A) 0.4 Hr.
DEALER CODING BASIC PART NO. CONDITION CODE 7213 69

NOTE: The information in Technical Service Bulletins is intended for use by trained, professional technicians with the knowledge, tools, and equipment to do the job properly and safely. It informs these technicians of conditions that may occur on some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by "do-it-yourselfers". Do not assume that a condition described affects your car or truck. Contact a Ford, Lincoln, or Mercury dealership to determine whether the Bulletin applies to your vehicle. Warranty Policy and Extended Service Plan documentation determine Warranty and/or Extended Service Plan coverage unless stated otherwise in the TSB article. The information in this Technical Service Bulletin (TSB) was current at the time of printing. Ford Motor Company reserves the right to supercede this information with updates. The most recent information is available through Ford Motor Company's on-line technical resources.

Copyright © 2007 Ford Motor Company
2010&c18=non-tab%20view&c21=07-14-07&c35=tsb%2c07-14-07&s=1366x768&c=32&j=1.3&v=y&k=y&bw=778&bh=347&ct=lan&hp=n&[aqe]

2/13/2019 2:01:54 AM • 2006 Mercury... • Answered on Feb 13, 2019
0helpful
2answers

Key stuck in ignition in park. Check charging system comes on. Dealership says it might be a fuse.

Key Stuck in Ford Fusion (2006 model) - YouTube

? 1:21 https://www.youtube.com/watch?v=3LVQttFOzGA Jun 18, 2014 - Uploaded by Jessica East #Ford #Fusion #Key #ignition #Stuck #FordFusion2006. ... i have a 2006 mercury milan and my key got stuck in there last night,... it to park with a little bit of force. will see what happens next time. good video, nice to know.

Key Stuck in Ignition While in Park

www.2carpros.com/.../2007-ford-fusion-key-stuck-ignition-while-park Dec 16, 2012 - KEY STUCK IN IGNITION / SHIFTER BINDING CONDITION FORD:2006-2007 Fusion LINCOLN: 2006 Zephyr MERCURY: 2006-2007 Milan
11/20/2017 9:26:12 PM • 2006 Mercury... • Answered on Nov 20, 2017
0helpful
1answer

This morning I went to get gas the car started

run the fault codes indicates a EVAP system problem or problem injectors check that you put the right petrol in the tank and not diesel or the other way around
11/14/2017 10:28:42 AM • 2006 Mercury... • Answered on Nov 14, 2017
0helpful
1answer

Need turn signal flasher module

Has no flasher module , uses SJB - smart junction box . FORD'S BCM - body control module . The smart junction box (SJB) monitors the multifunction switch position by sending multiple voltage reference signals to the multifunction switch. When the multifunction switch is in the LH or RH TURN positions, or the hazard lamp switch is engaged, that input signal is routed to ground. When the SJB receives a request for a turn signal or hazard lamps, the SJB supplies voltage to the appropriate turn lamps. You could by a used one off ebay or a remanufactured one . lot less cost wise. But you would need ford , mercury dealer program it . Yes $600 bucks sounds right from the dealer . 0results for 06 mercury milan smart junction box Search results for smart junction box
8/23/2017 6:44:49 PM • 2006 Mercury... • Answered on Aug 23, 2017
0helpful
1answer

How do you remove the panel from below the steering wheel of a 2006 Milan so that I can access easier to remove and replace the malfunctioning brake switch

Just look at it. There could be a few screws to remove or plastic plugs. Some remove by pushing a tab. all are at the front of the panel. Front meaning the furthest from the firewall.
1/8/2017 9:23:30 PM • 2006 Mercury... • Answered on Jan 08, 2017
0helpful
1answer

Diagram for serpentine belt 2006 mercury milan replace

Google this "Dayco Serpentine belt routing diagrams" Click the link and a very large pdf catalog will start to download, give it time.
11/15/2016 7:32:44 PM • 2006 Mercury... • Answered on Nov 15, 2016
0helpful
1answer

Ineed belt routing detail for 2006 mercury milan

Found this for 6 cylinder. 26356753-hq1bpfy1ehnkcnmysdwcgxrp-4-0.jpg
11/15/2016 7:05:14 PM • 2006 Mercury... • Answered on Nov 15, 2016
0helpful
1answer

Where is the horn located on mercury milan 2006

Safely raise and support front of vehicle, The diagram shows the tire removed, right front. Remove 4 screws in splash shield, pull down on splash shield to reach horn. The horn is number 4. Just make sure the horn is the problem and not wiring circuit issue, somewhere. Any time your working under a vehicle there are safety issues, safety is your responsibility. horn-located-mercury-milan-2006-stsmmaneq2has1s1u4tq5yee-4-0.jpg
6/13/2016 10:16:52 PM • 2006 Mercury... • Answered on Jun 13, 2016
0helpful
1answer

My Mercury Milan 2006 driver side front blinker is staying, while the passenger front side is not working

Sounds like theres a wiring issue. Check to see if the wires are cut
4/18/2016 10:34:47 PM • 2006 Mercury... • Answered on Apr 18, 2016
0helpful
1answer

Front Turn signal. one stays on other blinks once then goes off.changed switch..same thing

change bulbs and flashers
4/16/2016 12:38:41 AM • 2006 Mercury... • Answered on Apr 16, 2016
Not finding what you are looking for?
2006 Mercury Milan Logo

353 questions posted

Ask a Question

Usually answered in minutes!

Top Mercury Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Milan Mercury

  • Milan Mercury

Most Popular Question

mercury milan 2006 driver side front

  • Cars & Trucks
Loading...