20 Most Recent 1993 Ford Ranger SuperCab - Page 5 Questions & Answers


check the connection at the fan on the passenger side it could be loose. if it is reconnect it if it is not then check for power at the connecter . If you have power and connection is good, give the fan housing a good whack with a rubber hammer some times these old fellows just get tired and lazy.

1993 Ford Ranger... | Answered on Feb 10, 2013


There is a tool for it you can get at the auto parts stores.
1_26_2013_7_50_22_am.gif

1993 Ford Ranger... | Answered on Jan 26, 2013


bleed the system.....probly has air in system

1993 Ford Ranger... | Answered on Jan 25, 2013


Hi Monica,here's a link to the fuel pump relay,cost 14.99 to see,if not take back for refund.Here's another part to check.

1993 Ford Ranger... | Answered on Jan 20, 2013


It's common for a clutch's hydraulic system to get air inside. Mechanic's fix this by bleeding the lines briefly. Good Luck!-----------------------------------------------------------------------------
godiag key programmer

1993 Ford Ranger... | Answered on Nov 27, 2012


What i've been told or understand, is if your box behind the seat, which i believe is a 4x4 module of some sort, clicks then your actuator motor under the vehicle is stuck, broken or simply not engaging. Have someone pushing the button slowly while someone crawls under the car to tap the back end of the motor.

If this helps you are having an issue with the motor, its stuck and usually needs to be replaced.(the motor at a parts store is called a transfer case motor)(they have them at schucks).
c640e5d.jpg
If that doesn't help then you may be having the same problem i am.
I'm dealing with a similar problem the only difference is that my unit behind the driver seat doesn't click at all. The little led doesn't light up either. I don't think i'm getting power to that module. But finding a wiring schematic for the system is proving difficult.

1993 Ford Ranger... | Answered on Nov 22, 2012


if u took the bed off to change the fuel pump make sure u hook the ground back up to the frame the ground should be on the driver side behind the tank,u need to change the fuel pump relay when u change a fuel pump because it could be bad to cause the first pump to quit working. not the right amount of volts or to much volts,the relay is under the hood in the fuse box,

1993 Ford Ranger... | Answered on Oct 12, 2012


engine might need a seal.

1993 Ford Ranger... | Answered on Oct 12, 2012


Most are spot welded into place. The only way to do it is to cut them out, using a grinder to remove the spot welds as best as possible then removing the hinge with a dead blow hammer, or use a metal chisel to help dislodge it the rest of the way

1993 Ford Ranger... | Answered on Oct 12, 2012


For 1993 Ford Truck Ranger 4WD 3.0L MFI 6cyl the Control Module-Ignition is located under hood, center, rear engine area, mounted on distributor.

f2a2c92.jpg

Fig. 1: View of the remote mounted Ignition Control Module (ICM)

Hope this help (remember comment and rated this).

1993 Ford Ranger... | Answered on Oct 12, 2012


check battery/ positive connections and earth points

1993 Ford Ranger... | Answered on Oct 09, 2012

Not finding what you are looking for?
1993 Ford Ranger SuperCab Logo

621 questions posted

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Ranger Ford

  • Ranger Ford

Most Popular Question

truck check engine light when start bogs

  • Cars & Trucks
Loading...