20 Most Recent
2002 Ford Mustang - Page 7 Questions & Answers
Engine is "sputtering"
If engine light is on you can take it to auto zone or oreillys and they will put a code reader on it and look in the book for that code number and tell you why your engine light is on
1/11/2014 4:09:21 PM •
2002 Ford...
•
Answered
on Jan 11, 2014
Rpm fluctuation
There is an idle advance sensor, which increase the idle speed when the A/C is switched on, to stop the car stalling on tick over because of the load the A/C pump puts on the engine. The sensor may be giving wrong information to the ECU.
1/4/2014 1:03:25 AM •
2002 Ford...
•
Answered
on Jan 04, 2014
Cylinder 3 misfires
I would move no3 injector to another cylinder and see if the fault moved . If not the problem is in the injector wires or ECM plug If it moved I would consider a new injector .
12/29/2013 1:36:24 AM •
2002 Ford...
•
Answered
on Dec 29, 2013
Won't start, won't crank
have you crossed the solenoid terminals and checked the starter for operation? may have the battery cable burnt thru to ground by the exhaust side of the motor..it happens if the cable is up against the block..
12/26/2013 4:21:09 AM •
2002 Ford...
•
Answered
on Dec 26, 2013
White smoke...not missing but runs rough. No
WHITE SMOKE IS USUALLY COOLANT BEING BURNT UP
SMELL THE EXHAUST IF SWEET SMELL TO IT THAT IS IT
USUALLY HEAD GASKET FAILURE
PULL SPARK PLUG TO DETERMINE WITCH SIDE IS BURNING
THE PLUG WILL BE WITHISH DEPOSIT
MAY ALSO BE CAUSED BY INTAKE GASKET NOT INSTALLED PROPERLY
DOUBLE CHECK INTAKE FIRST MAKE SURE PORTS AND ORIENTATION IS CORRECT
BEFORE PULLING HEADS
11/12/2013 11:50:28 PM •
2002 Ford...
•
Answered
on Nov 12, 2013
My ignition is stuck in locked position and it
It sounds like the classic "switch needs replacing". You only need the tumbler replaced. Before installing the new tumbler take it and your door key to your local locksmith and they can key the new tumbler to work with the old key. This saves you from have to have two different keys.
11/2/2013 1:05:18 PM •
2002 Ford...
•
Answered
on Nov 02, 2013
How do I remove hub off of the end of the ball
You can buy a special tool for spreading ball joints. It looks a bit like a large tuning fork with beveled tines. Place the open end between the ball and the hub, and hit the other end with a heavy hammer. The joint will separate and you can then remove the hub.
10/12/2013 3:04:08 PM •
2002 Ford...
•
Answered
on Oct 12, 2013
How to change the a/c compressor clutch?
changing the clutch does not require flushing system. only time system is flushed is when compressor goes bad but you are doing just the clutch. how much more for compressor and are you sure compressor is good? why did clutch go bad? most clutches go bad due to bad compressor, they burn out ,unless it just shorted and wont engage.
6/29/2013 10:50:02 PM •
2002 Ford...
•
Answered
on Jun 29, 2013
Fuse box diagram
With a little work, the Autozone site will allow you to look at a diagram after you register your vehicle for free. At the bottom of their Webpage in the Help section you can sort between the pay site info and the free info.The fusebox diagrams may be part of the wiring category. They allow you to look up 12 vehicles for free and after that you must pay on their site.
6/9/2013 3:14:57 AM •
2002 Ford...
•
Answered
on Jun 09, 2013
Not finding what you are looking for?