20 Most Recent 2005 Dodge Ram 1500 Questions & Answers

Question edited for clarity and spelling of 'module'. Question moved to model category. No reason given for wanting to know where it is.

What's the ram 1500 bcm location?

Vehicle History https://www.vehiclehistory.com > questions > whats-th... 6 answers For the 2015 Ram 1500, the BCM (body control module) can be found on the driver's side of the car. It is located in the fuse box. If for any reason the BCM . More here https://www.ramforumz.com/threads/body-control-module.277957/ https://www.youtube.com/watch?v=RcjBUdL1ZoA

Check the sensors and the connections on each wheel.

Mr. Blake, no engine told. not what fire means, ? he means RUN not FIRE! gee if it can NOT crank then it can not start (will mine can by push started or gravity started) 6speed M/T (grin) on all modern trucks, like we do this. 1: fuses all good 2::no crank we jumper cable jump crank it, first as all tow truck driver do. (as seen by AAA autoclub, tow service) watch them. 3: battery not dead.,charge it or have the shop load test it. or the lugs are loose and green with rust, clean them. 4: alternator not dead, well jump start it and runs but battery voltage is not 11v to 15vdc running so the ALT is dead or its HUGE 100amp fuse blown. 5:PRNDL dead, shift to N and cranking ,if good, P switch is bad. the users manual shows how to crank it in Neutral using the brake pedal (keyon, step on brake, shift to N) top fail is corroded battery lugs for 100 years. counting. or left on head lamps even tie.

It should be inside of the fuel tank. The pump, sending unit, pressure regulator, and filter are all in one unit.

Question edited for clarity. Question moved to model category. In the link https://www.google.com/search?q=2005+Dodge+Ram+4.6+litre+truck.+Location+of+the+fuel+filter ..

Which manifold? Out of the exhaust pipe is normal at this time of year. We have had 6 questions in the last week and it happens every year as the weather turns cold. Your gasoline contains water are molecular level. The heat of combustion turns it to steam and it condenses in the cold exhaust and drips as water. Lots of questions about 'white smoke' coming from exhausts. That is called 'steam' :>D

Alternators have different outputs for dodges.. get the higher amp output alternator. Especially if you run a few accessories in your cab.

Check the bulbs. DAYTIME Running Lights are controlled by the Body Control Module. You need an auto electrician for that. No fuse covering them. https://fuse-box.info/dodge/dodge-ram-1500-2500-2002-2008-fuses ..

Question edited for full year make model. Question moved to sub category. The videos and articles may help https://www.google.com/search?q=05+3500+diesel%2C+fuel+line+check+valve ..

Hi: I would use the NGK Plugs Myself:
Spark Plug is a NGK-Laser-Platinum
(NGK PART # 4997) You Know Theres 2 Plugs Per Hole. I Think you'll Be Very Saisfied with These Plugs.

See the videos https://www.google.com/search?q=2005+dodge+1500+hemi+replace+lower+idler+pulley ..

THIS ENGINE HAS ELECTRONIC THROTTLE CONTROL..THERE ARE 2 THROTTLE POSITION SENSORS LOCATED IN THE THROTTLE BODY,COMPLETE ASSEMBLY MUST BE REPLACED IF DEFECTIVE..IT ALSO HAS SENSORS IN THROTTLE PEDAL ASSEMBLY AS WELL..WHAT TROUBLE ARE YOU HAVING?

there is help in the link. https://www.google.com/search?q=2005+Dodge+Ram+1500+Hemi%2C+no+communication+with+PCM ..

When the fuel pump was replaced was the fuel level sending unit replaced also ? Or was it part of the new fuel pump module ? If the sending unit was also replaced an the gauge still isn't working you have a faulty gauge or wiring problem , maybe . Your best bet mite be to have a qualified repair shop check it.

I don't think there is a flasher unit on Dodges newer than 2004. It's all electronically controlled through the TIPM (totally integrated power module) on the left front fender based on selections from the multifunction switch (turn signal lever and hazard switch). The clicking sound is generated by "an electromechanical relay soldered onto the instrument cluster electronic circuit board that will produce a clicking sound to emulate a conventional turn signal flasher."

With the correct tools, not too bad at all. In a driveway laying on the ground with jack stands, it can be a bit of a challenge, but doable.

You should go to www.reliable-store.com they have got books on every vehicle and also how to service/repair it, parts info, fuse box, gear box, torque specs,coiling, wiring diagrams, electrical diagrams, fuse diagrams, error codes, etc everything

Go to www.reliable-store.com you will get all info and solutions there definitely

indicates no brake pads take it to a professional brake shop for a proper diagnosis

How was the heater core verified ?