20 Most Recent
2000 Chevrolet Silverado 1500 - Page 3 Questions & Answers
Fuse box 2000 Chevy silverado
there are like 3 for a 2000 chevy silverado. 1 on left side of dash accessible only when door is open. 2 on right side of dash, not sure those fuses are applicable to you tho, and 3 under hood beneath a plastic cover that you snap off by pulling on.
Replaced o2 sensor bank 1 sensor 1, now reading "Circuit Low Voltage Bank 1 Sensor 1" and P0154 on Bank 2 Sensor 1. Live readouts on both show avg of .48V. What is wrong?
Lets examine your readings first.
Code 154 means the sensor is not switching from lean to rich enough in 60 seconds. And there is no such thing as average voltage.
The O2 sensors generate their own voltage by measuring oxygen in the exhaust. They also have heaters that get power from a relay.
But a problem with the heaters should be a different code.
When the engine is running, the computer varies "on" time for the injectors based on engine temp, throttle position, and unburned fuel in the exhaust. So when the O2 sensors send voltage higher than .5 to the computer, the computer calls that RICH and shortens on time for the injectors. Then when the O2 sensor drops voltage down below .5 it reads LEAN, and the computer lengthens on time for the injectors.
This back and forth switching should happen several times each minute. Like the tick tock of a clock.
If the sensor(s) are slow to switch, or they stay on lean or rich for more than 30 seconds, you get the code 154. Each sensor has a different code for the same issue.
It could be a sensor problem, or a fuel problem, or something else.
Too lean can be low fuel pressure, too rich can be not enough air flow coming into the intake.
Broken heater coil
If you mean the heater core is leaking. Here is how to change it:
Heater Core
Removal & Installation
Heater core removal
To Remove:
- Remove the HVAC assembly.
- Remove the heater core cover screws.
- Remove the heater core cover from the HVAC assembly.
- Remove the heater core gasket from the core.
- Remove the heater core from the HVAC module assembly.
To Install:
- Install the heater core to the HVAC module assembly.
- Install the heater core cowl gasket to the HVAC module assembly.
- Install the heater core cover and screws to the HVAC module assembly.
- Install the HVAC module assembly to the vehicle.
How do you "adjust" the doors on a 2001 chevrolet silverado
Both the hinge bolts and the latch bolts can be slackened off and the door position changed. It's a matter of determining where you want to have it, where it is now, and around what point it has to move to get the desired result.
Sometimes it helps to support the weight of the door on a small floor jack. Use a block of wood to prevent damage to the door.
WHAT YEAR MODEL DID THEY SWITCH OVER TO THE NEW FREON
I think around 1993 and some 1994 had r12 but if you look on top of the dryer, if it is the original it will tell you what type to use to recharge the system. or on the radiator support in the front there is a sticker with the type on it.
Air conditioner low side
The low side is the side with the dryer on it. If you are going to charge the system with a can you get at Auto zone or one of those auto parts store they will only fit on the low side as the Schrader valves are two different sizes on the low and high side.
Trying to adjust outer door handle rod. how to
Once you remove the door panel, you will see the linkage and rods. The rods are connected with these little "swing away" plastic fasteners. Basically, these fasteners have a hole on one end and a sort of channel which snaps onto the connecting rods. To remove them you just unsnap them from the connecting rods. I'm enclosing 2 pictures of typical awing away connectors. In the pictures, it's the square end which needs to be unsnapped. Hope this helps, if you need any further clarification, just post a comment.
Both rear calipers sticking closed
possibly
but I would be more interested in checking the hand brake action as they have a habit of sticking after being applied , especially if the correct procedure to get the clearance for the new pads was not followed
How do I install heater coil?
Basically, you have to remove about have of your underneath dashboard on the passenger side in order to get to your heater coil.
Plug gap setting for chev 5.3L
AC Type 41-932
(GAP 1.52 mm, 0.060 in)
AC Type 41-932
(GAP 1.52 mm, 0.060 in)
AC Type 41-932
(GAP 1.52 mm, 0.060 in)
AC Type 41-932
(GAP 1.52 mm, 0.060 in)
Not finding what you are looking for?