2001 Ford Mustang - Page 9 - Answered Questions & Fixed issues
My car doesn't have a fuse diagram and my
just pull them all out one at a time till you find the blown one .but if all fuses all ok then change the hazard warning light switch as this is the most likely unit to fail and cause these problems
9/26/2011 7:47:10 PM •
2001 Ford...
•
Answered
on Sep 26, 2011
•
179 views
Getting p1504 error code for
Your code designates an Intake Air Control circuit malfunction. Without proper scanning tools, you will probably have to take it to a qualified mechanic. Sorry I can't help you more, but without the car, that's all the info I can give you.
9/22/2011 11:10:33 PM •
2001 Ford...
•
Answered
on Sep 22, 2011
•
529 views
2001 Mustang GT. Motor shut
Hello and welcome to FixYa!
You may just have system failure. As a first course of action, I
strongly suggest that you remove the positive battery connector and let
it sit for at least 5mins. before reconnecting it. This will reset the
system and can get your vehicle back to it's normal operation.
This thing really happens and reconnecting the positive battery
connector serves like a jumpstart to the vehicle's PCM (powertrain
control module).
Hope this helps and thank you for using FixYa! Have a good one!
9/18/2011 2:16:46 AM •
2001 Ford...
•
Answered
on Sep 18, 2011
•
293 views
Speed odometer quit working and
Sounds like a vehicle speed sensor..Which is mounted on the transmission..It contros your speedometer plus effects transmission shifting
9/8/2011 10:35:17 PM •
2001 Ford...
•
Answered
on Sep 08, 2011
•
307 views
Ford mustang tries to start
try spraying starting fuid into the throttle body and see if it runs then for a few seconds. If yes, check fuel pressure. It should be 34 psi with engine running, 40 psi key on engine off. More liley th pump in the fuel tank.
9/8/2011 1:43:12 AM •
2001 Ford...
•
Answered
on Sep 08, 2011
•
356 views
How do you remove a gas tank from a 2001 Mustang?
try to do this with 1/4 of a tank so the weight is not as heavy,disconnect the fuel lines and vacum lines,electrical connections when you have access to them,undo the filler neck to the tank and undo the gas tank straps with a jack under the tank to lower it slowly to remove.
9/4/2011 8:15:20 PM •
2001 Ford...
•
Answered
on Sep 04, 2011
•
402 views
I have a 2001 Ford Mustang V6, the ac is blowing
it's either low (in spite of your readings) or your a/c clutch is not working correctly or you have too big an air gap in the clutch.
First, just disconnect the 2 pin connector from the a/c pressure cycling swithc and jumper the 2 pins with a wire to force the clutch to stay engaged. See if it blows cold then, and stays engaged. You can run this way for about 15 minutes before you have to pull the plug.
report reulsts.
please don't forget to rate.
9/1/2011 7:43:12 PM •
2001 Ford...
•
Answered
on Sep 01, 2011
•
1,852 views
I have a 2001 ford mustang and i am trying to
The fuel safety switch is located in the trunk on the drivers side just forward of the tail light.
You'll have to remove the drivers side trunk carpet liner to gain full access to it.
9/1/2011 10:09:19 AM •
2001 Ford...
•
Answered
on Sep 01, 2011
•
631 views
I have a 2001 Ford
Rattles could be anywhere in a car. Most of the time it is a bolt that has loosened and allowing something to move back and forth. Suggest you try to localize the rattle to which area of the engine from sound and then push and pull on items and see which one moves in that area.
Most of the things that would rattle, are not things that would cause over-heating, so I wouldn't worry on that account.
8/29/2011 2:27:42 PM •
2001 Ford...
•
Answered
on Aug 29, 2011
•
170 views
2000 ford explorer p1504 code
P1504 Idle Air Control Circuit Malfunction
here are possible causes
IAC circuit open
VPWR to IAC solenoid open
IAC circuit short to PWR
IAC circuit short to GND
Damaged IAC valve
Damaged PCM
heres what I would check, This code means that there is a fault in your IAC valve located near the throttlebody.
8/27/2011 5:43:18 PM •
2001 Ford...
•
Answered
on Aug 27, 2011
•
1,793 views
There is condensation around the exhaust pipe is
Condensation on exhaust pipe is normal.
Gas cap light:..This may be caused by loose or leaking hoses, loose or broken fuel cap, a leak at the top of the fuel filler pipe neck, ect......
8/22/2011 7:06:36 PM •
2001 Ford...
•
Answered
on Aug 22, 2011
•
163 views
2001 mustang convertible. How
The seat bottom is held in with 2 release buttons located left and right of the center of the seat. (see photo) push with a screw driver and lift, then pull the seat bottom forward and remove.
The rear seat back is help in place by 2 self tapping bolts on the lower left and right of the seat back near the floor, if I remember correctly you'll need a 10mm socket. Remove the 2 bolt and lift up to remove the seat back. When re installing the seat back do not over tighten the bolts they have a tendency to strip.
8/18/2011 1:26:48 PM •
2001 Ford...
•
Answered
on Aug 18, 2011
•
833 views
I have a service engine
you have a sensor on the engine setting a trouble code. need to have the fault code pulled to see what is malfunctioning.
8/14/2011 3:30:15 AM •
2001 Ford...
•
Answered
on Aug 14, 2011
•
291 views
2001 mustang...6 cylinder. Car overheats
Check that the water pump drive belt is tight
Check that the cylinder head is not blowing.
Check the impleor on the water pump is not eroded
Check theair flow through the radiator is ok.
Check electric cooling fans operates if fitted.
Are you driving in to low a gear?
Are the brakes draging?
Check to see if you have some contaninated fuel
Check that the correct ignition time is ocurring at all engine speeds.
Best of luck Cliff UK
8/11/2011 7:51:12 AM •
2001 Ford...
•
Answered
on Aug 11, 2011
•
330 views
How do you replace a rear end differential
Hi, welcome to FixYa.com my name is Shawn and I will be answering your
question.
Remove the differential rear cover.
Remove the rear calipers and rotors.
Remove the 8mm bolt that holds the pin in and remove the differential pin.
Remove the ABS sensors push the axle in towards the center of the rear end.
Remove the c clip washers. You can now pull the axle out.
I hope my assistance helped you and resolved your
concern, if you need further assistance please ask.
8/8/2011 8:27:27 PM •
2001 Ford...
•
Answered
on Aug 08, 2011
•
208 views
Not finding what you are looking for?