The lock is broke, couldnt get key to turn the mechanism, used wd40 then the pins dropped, couldnt get key in lock, told to drill lock out, now I have no barrel and still cant see how to open bonnet. Any help please
Stuck lock, bonnet won’t open ,,,
You do not need to drill holes in the grill or pay ford £200+
DIY..How?
Look into the grill at the top you will find the bottom of 6 plastic revscrews, 4 you get two via the grill slots use a chisel and cut them off, Then one either end of the grill. Place the chisel between two plastic layers, gently lift , check and cut, one each end.
With a wiggle that’s the top loose, There are two clips holding the bottom in place Put your fingers through the bottom slot in the grill, push down clip and greatly pull the grill, do both sides, It won’t come right out but your aim to loosen it., The lock is held in place in a sleeve with a plastic clips each side, you have push the barrel with a suitable item, this is to push it out of the sleeve and out of its housing, It may need a tap!!
Gently wiggle and pull the grill off
Lock
The lock is a ‘lock barrel along a shaft to a white plastic coupling’ this fits in to the ‘bonnet lock’
The security is at the coupling to bonnet lock in the form of a cross shaped plastic key
The key is fitted and held in place in the coupling, and when installed it’s fitted in to the lock, and once it’s in the lock part it will not come out, so therefore any jolt, pull, movement dislodges the plastic key from the coupling side and due to its design it will not slot back in so the lock barrel just rotates
To open you have to apply pressure on the shaft towards the left and into the coupling and turn the key in the lock barrel at the same time in a aim to get the coupling to catch the plastic key (take a few minutes) but it opens in the end if this is the fault, (alternatively remove the two bolts that hold the bonnet catch to the bonnet)
Once bonnet open remove the bonnet lock mechanism, then with draw the lock barrel, shaft, coupling, By looking in side you will understand regarding the cross key
Anyway you need to remove one of the catches from the side of the plastic key This way it will fit back in to coupling.
Reassemble
This is a brief description But the cost to me was 45 minutes, £2 for a pack of plastic rivets / screws, and I cached my bumper with the chisel £5 for a touch up stick Total £7. Well worth the time and effort
Posted on Nov 01, 2009
I have a 2000 Ford Focus, when accelerating between 50 and 70 mph I get a lot of vibration from the front end but not much through the steering whell but you can feel it through the pedals mostly. I don't think it is balancing or shocks as it seems to go away post 70mp???
I am betting on a tire balance. I have had tires out that only vibrate at 60; they were pretty smooth at 75.
Posted on Aug 01, 2008
im trying to replace a clutch slave cylinder in a ford focus, does anyone have any pictures or information how to do this??
hi there to replace your clutch slave cylinder you will have to remove your gear box as it is bolted into gearbox.
Posted on May 04, 2009
my anti-theft system has lock my focus engine how do i unlock it
if the theft light is flashing fast, the PATS(passive anti-theft system) can only be reset with a ford scanner... you can try leaving the key in the on position for a little over an hour, sometimes it works.
Posted on Jun 22, 2009
need an digram of 2000 ford focus power steering pump
Item
Part Number
Description
1
-
Steering wheel
2
-
Steering column
3
-
Boot
4
-
Tie-rod
5
-
Tie-rod end
6
-
Steering gear
7
-
Steering gear to fluid cooler hose
8
-
Fluid cooler
9
-
Power steering pressure (PSP) switch
10
-
Power steering pump
11
-
Fluid supply hose
12
-
Fluid reservoir
13
-
Pump to steering gear pressure line
14
-
Steering gear pinion extension
Posted on Aug 09, 2009
i need a diagram of the serpentine for a ford focus 2002 z3
Hi
Thanks for using FixYa. You can look at this picture for serpentine belt for your 2002 Ford Focus Z3--
Ford Focus Z3 Serpentine belt Removal--
· Jack up the front of the vehicle and support it on jack stands. Use a wrench to remove two bolts and take off the drive belt lower cover.
· Note belt routing and make a sketch for your reference if you don't have a belt routing diagram from the manufacturer.
· Find the belt tensioner pulley. Use your wrench to rotate the tensioner pulley by pulling clockwise on a bolt in the center of the pulley. Slip the old belt off of the tensioner pulley.
· Release the belt tensioner. Slip the belt off of the pulleys and install the new belt according to your routing diagram.
· Rotate the tensioner again to allow the new belt to slip over the tensioner pulley. Release the tensioner again. Replace the drive belt lower cover and lower the vehicle.
Please do rate the solution and revert for further assistance.
Thanks
Rylee
Posted on Sep 06, 2009
looking for firing order diagram for 2002 ford focus se
2.0L SOHC
2.0L DOHC
Posted on Jul 31, 2010
looking for a pdf. of vaccuum hoses on a 2000 focus
SPI Vacuum Diagram
Zetec Vacuum Diagram
SPI Vacuum Diagram
Zetec Vacuum Diagram
Zetec Vacuum Diagram
If it's equipped with the 2.0L SPI engine (eighth digit of the VIN is 'P'), the most common place for a vacuum leak on these engines, is from the PCV hose that runs from the valve cover to the back of the throttle body. Where it usually rots through is the elbow at the back where it connects to the throttle body. Hope this helps.
The only place i could find any views is here.
vacuum hose diagram - Focus Fanatics
Posted on Oct 29, 2010
ford focus power door lock fuse location
I have a 2007 basic ford focus having problems pairing auto door unlock? Where is fuse. Thanks
Posted on Mar 07, 2020
3 door car no noise from pump when switching ignition fuses and relay fine
There should be a reset button on a part called an Inertia switch. This switch is located behind the front kick panels or in the trunk.
The Inertia switch is a safety switch used to prevent fires after a collision. But sometimes if the right Frequency is generated by closing a door, hood, or trunklid the switch will activate. Then power is cut off from the fuelpump.
Posted on Apr 12, 2013
5,166 questions posted
Usually answered in minutes!
2,612 Questions
2,055 Questions
1,226 Questions
897 Questions
840 Questions