2000 Ford Focus - Page 4 - Answered Questions & Fixed issues
Were is the fuel bleeder at?
When you first turn the key on, no crank, if you listen close to gas tank, can you hear the fuel pump run for a few seconds? If not, check proper voltage and ground at the fuel pump connector, engine cranking.
I have to ask, how long since a tune-up?
Are there any applicable trouble codes?
Anything else missing? engine cranking do you have spark at the spark plugs and fuel injector pulse?
5/6/2016 8:38:39 PM •
2000 Ford Focus
•
Answered
on May 06, 2016
•
86 views
2010 dodge journey electric door locks not working
They are known to have broken wiring in the drivers door jam the wires break from the door being open and closing ,I think there s recall for the harnesses for the front doors I could be wrong but check the harnesses on the drivers door the wires break at the connector just pull back the rubber around the harness?
3/19/2016 10:45:24 PM •
2000 Ford Focus
•
Answered
on Mar 19, 2016
•
2,272 views
Ford focus fuel pump
remove the rear seat cusion, thare should be a cover under the cusion with 4 screws take these out and under should be the fuel pump.
3/9/2016 8:35:57 AM •
2000 Ford Focus
•
Answered
on Mar 09, 2016
•
795 views
What do I do if I can not see timing marks on the camgears of a 2000 Ford focus Dohc anyone
according to autodata belt replacement guide , there are no timing ,marks on the cam gears
it require special tools and a good knowledge of mechanics to do the job so I strongly recommend that you get a workshop manual before starting on the job
I could type it all for you but with only two fingers , I would be here until next week as the directions are involved and you will need diagrams to full understand the procedure
that is why I suggest a workshop manual
the procedure is not as you would expect as on other engine makes and need to carefully followed
2/7/2016 8:40:40 AM •
2000 Ford Focus
•
Answered
on Feb 07, 2016
•
230 views
5-speed. How do I replace clutch and pressure plate?
remove transmission .do research find out what all tools needed.and type of fluid. make sure to have car stable and safe while under.might have to remove more than just the trans depends on car.make sure to place throw out bearing correctly seated in place are you would have done it all for nothing. cheak and make sure you have fluid in the container .break fluid will work just might be out of fluid.youtube has alot of vids
12/27/2015 5:56:35 AM •
2000 Ford Focus
•
Answered
on Dec 27, 2015
•
207 views
Loss of power engine hunting when stationary
Hi there,
cars are all electrical these days,
buy a cheap code reader off of eBay ( item no. 361240488837 )
plug it into your diognaustic plug and it will give you a problem code so you know what's wrong with the car,
a booklet comes with the code reader with the codes in it, sometimes it will throw up a code which isn't in the booklet so then you have to google the code, hope this helps :)
12/13/2015 9:18:07 PM •
2000 Ford Focus
•
Answered
on Dec 13, 2015
•
209 views
What are the probable causes of DTCs B1600, P0113, and P0179?
B1600
At some time since last clear the ignition was switched on without any key code being read.
P0113
Intake Air Temperature Sensor 1 Circuit High Bank 1
P0179
Fuel Composition Sensor Circuit High
In the back of the trunk of these cars are a box on the left hand side looking in the truck under the cosmetics of the floor, lift all that up and you will see a small box that you can reset, that goes out and you can not start the car, that goes to your fuel pump. Try, hope that is all that it is, because the codes do not reflect the starting problems you are having. Good Luck!
12/1/2015 1:12:13 AM •
2000 Ford Focus
•
Answered
on Dec 01, 2015
•
248 views
Not finding what you are looking for?