Can I repair a fuel line leak with tape or any sort of sealant so that I can drive it to a shop? 1993 Oldsmobile Ciera
not sealant But get small length of rubber hose,,, small ,as in just larger than metal line then get two small screw band clamps cut the leak spot with bolt cutters QUICKLY insert hose on two ends of line with CLAMPS ALREADY ON HOSE screw them tight stop at service dest inform them of gas leak so they can take precautions.
they will ask fix or replace say FIX so they don't chage you $120 an hour shop time to bend fuel line hose to replace entire line... NOT necessary..old school repair if fine replace line is $$$ and not neccessary very little pressure in fuel line mostly gravity flow you may even say its more practical
Posted on Jun 11, 2010
How do I adjust my headlights on a 1993 Olds Cutlass Ciera, the drivers side "low" beam is the worst, the high beam is a little better but not a whole lot; they are pointed way too low.
Please help.
AIMING
The head lamps should be aimed using a special alignment tool, however this procedure may be used for temporary adjustment. Local regulations may vary regarding head lamp aiming, consult with your local authorities.
Posted on May 22, 2009
hot to tell if my brake drums are going bad on rear tires
Going bad as in are they warped?? **Remember, safety first.....** If you have a working parking brake the easy way someone might check is to get going at a decent speed, clear of any traffic or obsticles and press down on the parking brake while ready at the release handle. If you feel the shake, it's probably warped rear drums
Posted on Dec 19, 2009
Need to replace the starter on a 1993 cutlass ciera and have no clue where it's located and what is needed to replace it.
According to Chilton's, and assuming you have the 3300 V-6, it won't be fun. The first instruction is to drain the air conditioning system, and remove the front manifold. The starter is between the engine and the radiator. The deal breaker for me is the A/C draining/refill. If anyone knows of a way to avoid the A/C drain, let me know. Otherwise, I may just preemptively replace mine before my buddy runs low on R-12.
Posted on Nov 13, 2008
how do I replace the drivers side front (4 door) power window motor on a 1993 cutlass ciera?
Disconnect the battery negative cable, carefully remove the door panel, make sure you remove all the visible hold down screws holding the arm rest and other things in place, be careful and observant, don't force anything. If you don't have the standard door panel removal tools, use a stiff putty knife or a wide screwdriver to remove the door panel, you will have to get the power window control switch and the lock control rods out of the way, take notes so you know how they go back together, Remove the plastic weather protection shield out of the way, try not to tear it because you will want to replace it using a good contact adhesive. Getting the motor and the lift mechanism out is the biggest challenge, There are two big rivets holding the motor and regulator assembly to the door, there are two more rivets closer to the rear of the door that holds the track and window guide in place. the rivets are difficult to drill out because it's not easy to center punch them. I used my 4 inch grinder to remove the rivet heads, be careful not to injure yourself or grind through the door metal. knock the rivets out. Remove the power supply wire from the motor. Use a 10 MM socket to untighten the two cap screws that hold the lift bracket to the bottom glass channel. Don't take the cap screws all the way out. Use a piece of wire to hold the window in the closed position. Loop the wire over one of the hold down cap screws and fasten the other end through one of the convenient holes near the top of the door. Now comes the good part. the motor and lift mechanism is all in one near rigid piece. The seat belt anchor blocks the door panel opening that would make it relatively easy to remove. Don't give up, the unit will come out with some thoughtful manipulation, the V shaped track guide will tolerate a small amount of flexing, don't overdo it. I finally got the assembly out by moving it as far to the back of the the door cavity as possible, use the angles of the assembly to your advantage to free it from the door. Once free, use a black marker to ensure you align your new motor in the correct postition. If you are replacing a complete assembly that looks the same a the part you removed, install by reversing the above directions. If you are replacing only the motor, drill out the two rivets that hold the motor to the lift assembly. this will be asy to do. fit your new motor in the exact same position, referring to the previous marks you made. If you are reusing the old lift mechanism, you should pull the perforated tape out of the guide, clean, inspect it, the guide and the tape, relubricate it, I used white grease, there is probably a better grease available. The motor assembly I received from an internet supplier came with rivets and machine screws to install the assembly, I used 1/2 quarter twenty nuts and bolts to replace the big rivets, I don't have a big enough rivet gun. If you go the quarter twenty way, use thread lock, install with bolt heads on the inside the door and flat washers and nuts to the car interior. Be observant, I left the plastic bracket that attaches the drive tape to the window bottom in an unsecure place, one of my dogs used it as a chew toy,so it was off to the junkyard one more time. Be sure to secure the tape properly at both ends. If it worn or frayed, several suppliers including rockauto supply them at reasonable cost. good luck.
Posted on Oct 10, 2008
fuse box diagram for 1993 oldsmobile cutlass ciera windows will not go down. where is the fuse and what fuse amp number is it
On this website, you find fuse box diagram and description for Oldsmobile Cutlass Supreme (1993)
http://www.autogenius.info/oldsmobile-cutlass-1993-fuse-box-diagram
Posted on Jul 29, 2017
what fuse goes to the torque converter solenoid?
the GAGES fuse. 10 amps.
Posted on Aug 30, 2011
removing harmonic balancer 1993 oldsmobile ciera 3.3
Air ratchet .
Posted on Aug 17, 2017
firing order for gm 2.8 V6
1993 GMC 2.8 liter V-6 VIN "R"
Additional details cpould be more helfull. Hope this helps. (remember rated and comment)
Posted on Sep 03, 2010
When I'm driving and the engine trys to shift from 2nd to 3rd gear it like slips or something and I push on the gas and it just revs the engine, and I'm still in drive. I can down shift to overdrive or "2" and it will continue driving. Is this my transmission going? Or something easier to fix and CHEAPER?
no you have a failed transmission on your hands, it is slipping.
Posted on Aug 13, 2009
796 questions posted
Usually answered in minutes!
540 Questions
492 Questions
476 Questions
412 Questions
332 Questions