Top 20
2007 Ford Mustang GT California Special Convertible - Page 2 Questions & Answers
Hi!
i started my mustang 2010
I would imagine it is still under warrenty, I would take it to the dealer and let them fix it before messing with it myself. If you touch it first they may deny any warrenty repairs.
8/30/2011 12:13:32 AM •
2007 Ford...
•
157 views • 1 helpful votes
Need to find fuse panel to fix fuse for auto
The only thing i saw for the seats was located in the power distribution box located in the engine compartment. Below is a diagram of the layout for that fuse panel. It says number 14 is for the drivers seat and number 15 is for the passengers. Not sure if this is what you are needing. This should be in your owners manual if you have one. If you do not have an owners manual and would like a copy, you can email me at
[email protected] with your make, model and year and I will be happy to email you a copy. I hope this helps and good luck.
4/27/2011 3:11:56 AM •
2007 Ford...
•
206 views • 0 helpful votes
I just noticed lately when
If one of your rear bulbs is burnt out then the signals will react this way. 2007 is not very old of a car for a signal delay problem. It would be more likely a bulb.
3/1/2011 3:29:49 PM •
2007 Ford...
•
435 views • 0 helpful votes
2007 Ford mustang lights go
Could be several things. The battery or alternator can be tested at most of your local parts store. I would start with those probably battery first then alternator as batterys are less expensive and earier to install. What ever u decide to do i would make sure to get both checked to avoid burning up a new battery if it is the alternator as well as the battery.
2/4/2011 4:04:49 PM •
2007 Ford...
•
424 views • 0 helpful votes
I have read numerous threads regarding output of a
It all depends on the condition of your battery. The voltage will vary from about 13.2 to about 14.6. Thje voltage regulator increases the voltage with load and decreases the voltage when the battery is fully charged with no load. It is pretty safe to assume that if the voltage at the battery is 13.2 or above with the engine running and the headlamps on, that your charging system is working. If you leave your lights on for about 10 minutes with the engine off, then start your engine, the voltage will jump up near to the 14.6 mark, then gradually decrease as the battery recharges.
1/29/2011 3:38:36 AM •
2007 Ford...
•
233 views • 5 helpful votes
I'm a mother trying to
head lamp fuse is either under the hood close to battery or inside under driver side dash look at owner manual it will show you wich one cause some cars the sticker on plastic comes off
1/13/2011 7:34:45 PM •
2007 Ford...
•
202 views • 0 helpful votes
If the vehicle is in a serious accident at the
yes all vehicles have these type of engine mounts ,its part of the europeon homoglonation certificate ,now as for a black box well as far as i know only airplanes have this ,but yes some functions will throw a code up like the airbags and will need to be reset before a repaired vehicle can be passed for its annual technical inspection
11/12/2010 7:35:25 PM •
2007 Ford...
•
51 views • 0 helpful votes
2007 mustang gt. headlights come
Garvin,
It seems that the headlight wire is shorting intermittently with the power wire of the car. That is why when the ignition is on the wires short due to some bump or something. It does not have to be far off. Just close to the ignition switch. If you can locate it then wrap a tape around it and drive happily thereafter.
Happy motoring.
9/29/2010 5:27:07 AM •
2007 Ford...
•
86 views • 0 helpful votes
Po420 bank 1 and po430 bank 2 error codes
sounds like O2 sensors to me. I havent changed one on a mustang yet but I havent had any trouble with any others that I have done, they screw in like a spark plug but you will need a special tool, I hope this helps you.
5/13/2010 2:13:18 PM •
2007 Ford...
•
1,656 views • 1 helpful votes
Is there somthing in the vehical serial number
If you call a Ford dealer parts or service dept. and give them the VIN number they can tell you pretty much everything you want to know about what you have. Often they only need the last eight digits but I usually have all 17 handy just in case. More and more you'll find that you need the last 8 digits of any VIN to order the correct parts for many vehicles as it contains much of the information needed to sort out all the various options the vehicle may have come with. Hope this helps!
7/13/2010 2:33:55 PM •
2007 Ford...
•
67 views • 0 helpful votes
Idle it irregular on my 4.6 V8 mustang 2007
DIRTY AIR FILTER AND DIRTY FUEL INJECTORS.PARTIALLY CLOGGED FUEL FILTER.YOU COULD HAVE DIRTY THROTTLE PLATES ON THROTTLE BODY HAS A SLIGHT CARBON BUILT UP AROUND THE PLATES.
4/18/2010 4:22:24 PM •
2007 Ford...
•
433 views • 0 helpful votes
Need to know how to put the top down on 96 mustang dont have manu
First thing to do is put the car in park and then set the parking brake. Next, release the drivers and passenger side handles (located at the top, above your head when you are sitting in the car, where the part of the top meets the windshield) Both handles are black and you simply pull the lever to release the hooks. After both hooks are released, push the button located near the speedometer (should be underneath the speedometer) on the dash and the top motor will engage and begain to retract the top. Hold the button untill the top disapears behing the back seat
2/28/2010 7:28:04 AM •
2007 Ford...
•
1,416 views • 0 helpful votes
Once in awhile the head and tail lights come on
where does the vehicle sit when this happens is it a residential area or near a radio station or someones garage or even there cb beam what im trying to say is there maybe some bleed over from something that puts out strong signal ive played around myself with my cb and had a kicker/booster that would come across peoples tv and through pa systems like hardees drive up they where not happy with me anyway you see what i am saying.
2/22/2010 6:43:56 AM •
2007 Ford...
•
178 views • 1 helpful votes
I need to know how to install a serpentine belt on
put a socket wrench on the tensioner pulley and act like you are tightening it when you do that it will take tension off of the belt and then take it off and put the new one on in the same direction and repeat the process on the tensioner and you will be able to install it no issues
1/9/2010 6:51:59 AM •
2007 Ford...
•
269 views • 0 helpful votes
Not finding what you are looking for?