20 Most Recent 2005 Jeep Grand Cherokee Laredo Questions & Answers

Question edited for clarity. Question moved from Motorcycles category. Wow, as my old Dad used to say "they saw you coming", and you got properly ripped off. Get a man to drop the car off and to go back and pay (with your card) and pick it up. No, the O2 sensors are likely to be fine is there are no codes. If the mixture is running lean, it can cause overheating, but the catalytic converter is made to run hot. Try spraying the gas cap seal and the gas tap tube top with WD40, wait a minute and clean it off with a cloth. Spray it again and put the cap on. Also run a bottle of this through it to clean the Cat https://www.duralube.com/products/severe-catalytic-exhaust-treatment?_pos=1&_sid=622a1de88&_ss=r .And then when that has been used, run a bottle of this https://www.duralube.com/products/severe-fuel-system-cleaner ...

Check the owners manual. If you lost it then try this site. ManualsLib Makes it easy to find manuals online

check the speaker connection it might be loose

Well, yes and no! This will be a pretty big job, as you should have to take the rear door all apart to get at the broken parts inside the door. Often, the broken part may be nothing more than a plastic clip or bushing that has failed. You may discover the job to take all day. God bless your efforts.

Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem. Best Manuals

they are typically located in the air snorkel in between the air filter and the throttle body. It will have a 2 wire connector with a red lock tab. I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

2005 Jeep Grand Cherokee Service Repair Manual INSTANT DOWNLOAD You can easily download the pdf file

Could be bad plug wires, bag coil packs, bad injectors.

Carefully check your routing and make sure that all spark plug wires are attached to the correct spark plugs otherwise your firing order will be mixed up and cause the issue you are having. Also make sure that the wires are firmly seated on the coil packs or distributor, whichever is on your vehicle.

The tire pressure monitors are made in the valve stems. You will have to replace the valve stems then have the codes cleared at the shop. Most tire stores have the tool to reset the tire pressure monitors. It can be a little costly.

Whew! Tight spot. Here are some quick and some more involved things to check. Hopefully, another responder will pitch in. A good time to call AAA. Troubleshoot this issue step by step: Check for Spark: Crank the engine and check if there's a spark at the spark plugs or ignition coil. If you have a spark, the crankshaft position sensor (CPS) is likely not the problem. Fuel Pump Operation: When you turn the key to the "on" position (but not start), you should hear the fuel pump run for a couple of seconds. If you don't hear it, there might be an issue with the fuel pump or its relay. ASD Relay: The Automatic Shutdown (ASD) relay controls power to essential components like the ignition coils. If the ASD relay is faulty, you won't get spark. Check and replace it if necessary. Throttle Position Sensor (TPS) and Intake Air Temperature (IAT) Sensor: Ensure that these sensors are functioning correctly. They play a crucial role in engine performance. Check the Key: If everything else checks out, consider the key itself. The chip in the key has a unique identifier code. Some replacement keys may mimic this code, so make sure your key is genuin.. Bus Line and SKIM Module: Verify the PCI bus line between the PCM/data link connector and the SKIM module. If there's an issue with communication, it could prevent the engine from starting

It is a known issue.

The driver side power seat in my 2017 Jeep Grand Cherokee

JustAnswer https://www.justanswer.com > Jeep Questions Nov 28, 2023 - Every other part of the power seat works (lumbar, vertical adjustment etc) but for some reason it is not moving forward or backwards. I checked ... 1 answer · Top answer: Welcome to JustAnswer. Sorry to hear you have a frustrating experience. I'm glad to assist ... Missing: Overland. ‎' Show results with: Overland.

Driver seat is stuck rearward

Jeep Garage https://www.jeepgarage.org > threads > driver-seat-is-st... Aug 19, 2012 - I have 2004 Overland that automatically moves forward and rearward when unlocking and locking the vehicle. The seat is stuck all the way ... Easy exit seat not working Feb 18, 2018 Driver seat won't move forward Apr 4, 2016 Seat Memory, Easy Entry/Exit not working Aug 3, 2018 Memory Seat not working Feb 23, 2010 More results from www.jeepgarage.org

FIX: front seat stuck forward or seatback won't return to ...

JLwranglerforums.com https://www.jlwranglerforums.com > forum > threads Jan 8, 2022 - It's a known issue. There is one for each seat and it moves along the door-side track. The left and right sides specific and not switchable.

old fords have them and yours does tomine not. ,not my JK Nor wk. I have your real factory service manual here on screen 2. yes, replacing the alternator with the battery connected does blow a fuse. in 1 nano second fast. BOOM , let the smoke out. but saved by the link. OKAY you were right the liberty has that link you were right, it has links ! this is your actual car, wiringi have it all there. FSM PDF real.

So it really is only a jeep XJ body ,not a real jeepsure loved by all sure.jeep has 2003 avalanche LS5.3 ENGINE AND 4L60E TRANS WITH A 6" Lift (ouch) on 37" tires with 1979 Ford 3/4 ton rear ends.with NP231 transfer, np207 gone now with new NP231 transfer case from the '91 YJ ?, NO, from a CHEVYI bet now it is NP231C box, the C means Chevy box.with 2H, 4H, N, and 4L,, this is part time 4wd, not full and is not for the 4wheeling on pavement. only offroad or on ICE.ICE means, just that or snow or snow over ice. (sorry captain Obvious, just left the building,now)end ICE answersbegin, 6" lift extreme problemsthe real problem is the LIFT that high.3 "easy4 hard6 "extreme lifts.IT fails in 2wd mode too, that is because U-Joints have limits. (all do) and the lift span chart below.(angle) post.nothing else needs to known, but U-JOINT ANGLES are all WRONG.SOLVED,. the 6" lift done wrong. YJ is a very short Wrangler and very short rear prop shaft.that means Prop(rear) drive shaft angles are dead wrong. (solved the reason on 1 fact)DOne with no SYE kit. "slip Yoke Eliminator"'https://www.amazon.com/Heavy-Eliminator-52231-18676-60-Driveshaft/dp/B00FDWL7PMdone i bet with no shims for rear axle LEAF spring perches , to get angle right(they sell shim kits)the answer You need a double cardan or CV (same piece different name) at the TC case, this will require a new yolk. You will also need to shim the pinion angle to get the driveshaft and pinion within 2 degrees of each other.

First you will need to determine if there is a problem with the electrical system or fuel system. Connect a fuel pressure gauge to the fuel rail to see if you have pressure when the vehicle dies. It it maintains pressure and the vehicle dies, then check to see if there is a spark issue. Fuel issue could be bad/weak fuel pump, bad relay or restriction in fuel delivery system. No spark could be ignition coil, bad computer, bad electrical connection or relay. To check these systems you need special meters and scanners. Best to take to a repair center.

The most likely reason is a faulty switch or a faulty relay or problem with the Body Control Module computer. https://www.google.com/search?q=auto+electrician+near+me ..

1. Faulty Instrument Cluster: The instrument cluster itself may be defective or damaged. Over time, electronic components can degrade, leading to malfunctions.
2. Fuse: Check the fuse box for any blown fuses related to the instrument cluster. A blown fuse could disrupt power to the cluster, causing all the gauges to fail simultaneously.
3. Faulty Wiring: There could be a problem with the wiring harness or connectors that supply power and data to the instrument cluster. Loose connections or damaged wires can prevent the cluster from receiving the necessary signals.
4. Vehicle Speed Sensor: The vehicle speed sensor (VSS) is responsible for providing speed data to the instrument cluster. If the VSS malfunctions, it can cause the speedometer to stop working, and it may affect other gauges as well.
5. Engine Control Module (ECM): The ECM communicates with the instrument cluster to provide data for various gauges. A malfunctioning ECM could disrupt communication and cause all the gauges to fail.
6. Grounding Issues: Poor grounding can lead to electrical problems, including instrument cluster malfunctions. Ensure that all ground connections related to the instrument cluster are clean and secure.

Given the complexity of diagnosing electrical issues, it's advisable to have a qualified mechanic or automotive technician inspect your vehicle. They can use diagnostic tools to pinpoint the exact cause of the problem and recommend the necessary repairs. Additionally, if the issue is related to the instrument cluster itself, it may need to be repaired or replaced by a professional.