20 Most Recent 2012 Buick Enclave Base 4dr SUV 3.6L V6 6-speed Automatic Questions & Answers

It's not that simple, the factory amp is monitored by, and fed data and signals from the Body Control Module. It is used for chimes and warnings and sounds like your indicator 'clicking'. https://www.google.com/search?q=2012+buick+enclave+stereo+wiring ..

Question edited for a lot more clarity! Question moved from Watches Category. All here, with videos as well David. https://www.google.com/search?q=2012+Buick+Enclave.+Where+can+I+find+the+bank+2%2C+sensor+1 ..

Question edited for clarity. Question moved to sub category. It's up under the dash next to the steering column. It has a bunch of various colored connectors all in a row. You have to remove the trim panel above the pedals to access it.

Body Control Module???? Where is it?? ' EnclaveForum.net

Pretty pictures too https://www.google.com/search?q=2012+Buick+Enclave.+Location+of+body+control+module ..

That is not any code that I have ever seen. OBD2 codes look like this example of a lean O2 sensor fault code: P0171

That is in the owner's manual. If you do not have it go to the GM owner's site and download the owner's manual it is free.

Dear Renee, I hope I am not wrong, but I think you have only turned on the light in the radio. With the new technology since about 1990, the radio has 2 circuits, one is the light, the other is the radio itself. This is also hooked in to the "anti-burglar:" protection, which is some cases prevents theft of the car. You may likely need a new radio, or to have yours repaired. I have used some places on the computer to have mine fixed. Type in "car radio repair" into your search engine. God bless your efforts

see page 2-21 in this document for reprogramming power windows. https://www.buick.com/content/dam/Buick/north_america/usa/nscwebsite/en/home/owners/vehicle_manuals/2012/02_pdf/2012-enclave-owner-manual.pdf

Three possible reasons for this are 1. You have a vacuum leak 2. The throttle position sensor (TPS) has gone bad 3. The idle air control valve is bad or blocked up.

Need to use a scanner to see if there are any codes pertaining to the transmission. https://www.acadiaforum.net/threads/2010-wont-shift-out-of-first-at-cold-start.13432/

Checked code's where ? Full system scan or just OBD2 . What type scan tool ? Or is it just code reader ?

Hello. It seems either your a/c control panel is defective/malfunctioning and/or a freon condition; either too much or too little. Good luck and keep me informed; if you want to.

You can do it yourself. Apparently it is called a Power Window Reset and the instructions are in the manual. https://www.enclaveforum.net/threads/auto-up-windows.8058/ videos here as well https://www.google.com/search?q=buick+enclave+power+window+motor+programming ..

Yes,you should be able to move the blend door with your fingers

Yes there is a air temperature control door and that is moved by a small electric that can hold its position according to the temperature setting you desired.

Actually, a new rear wiper module/motor is probably needed. The logic controller is on the motor so the entire motor has to be replaced. I believe the switch is on the center console and I think you will need to remove the outer trim to get at the switch. It may be a switch that just snaps in, so I would get a look at a new one before digging into the job.

What year ? The relay's are located in the under hood fuse box . With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER relay, the WIPER HI relay and the WSH relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics. Which wipers are you talking about ? Front or rear . Rear wiper fuse is in the I/P instrument panel fuse box . Fuse Block - I/P Under the lower right side of the instrument panel